TA.JINlA O-RM01-E User Manual

O-RM01-E
(9911)
USIR'S
MANUAL
PARTS
LAME
ATTACHMIN1
LIST
/J/J/J
TA.JINlA
[Y[Y[Y
FOREWORD
FOREWORD
This User's Manual and Parts List describes the using and setting methods for the lame attachment.
Please read through this manual setting the attachment.
of
The contents
[IMPORTANT SAFETY INSTRUCTIONS] [SETTING [EMBROIDERY USING LAME FILM] [PARTS LIST]
Always keep this manual at hand whenever you need. If
you do not use the lame attachment, keep this manual for future use.
This manual may contain discrepancies in detailed information when compared with actual product ued research and improvements
If TAJIMA
due
any question about the unit
distributor.
this manual are largely divided into the following sections.
THE LAME ATTACHMENT]
to differences
carefully and understand the contents before operating
in
machine models for which the product is used and also contin-
of
the product.
or
contents
of
this manual arises, please consult your local
or
(CG11)
IMPORT ANT
SAFETY
INSTRUCTIONS
IMPORTANT
Correct work is required for safe handling (using and setting) Please read the IMPORTANT SAFETY INSTRUCTIONS
carefully items written under
which require your special attention on the using
Items specified to ensure safety during using and setting the attachment.
Signal word definition is given below.
Indicates a potentially hazardous situation which, or
moderate injury (*1) or property damage.
*1:
{S)
SAFETY
and do not attempt operation
following the warning symbol and signal word. These items must be strictly observed
INSTRUCTIONS
in
of
the machine before you thoroughly understand the
IMPORTANT SAFETY INSTRUCTIONS.
and
of
the lame attachment.
this instruction manual and parts list
setting
of
the lame attachment are
A CAUTION
if
not avoided, may result in minor
An
injury that does not necessitate hospitalization or visit
Prohibited
items
to
a hospital over a
long
period.
0 : Items
The information which gives
NOTE.
that
must
details
be
followed
carefully
or
supplements the explanation appears under the title
to
ensure safe operation.
A CAUTION
Before carrying
power switch OFF. If
you attempt an operation with the power switch ON, the machine could
operate unexpectedly and
out
operation described in this manual, make sure turn the o
could cause injuries.
A CAUTION
Oily chips When cleaning the ATH device, make sure to completely remove lame film chips.
Thread
of
lame film may adhere
will not
be
trimmed correctly
to
the ATH knife
if
lame film chips remain on the ATH knife.
or
the rotary hook. o
ii
(CG11)
CONTENTS
CONTENTS
FOREWORD ................................................................................................................................................ i
IMPORTANT SAFETY INSTRUCTIONS ....................................................................................................
SETIING
1.
2.
"ll
t.l.
THE
LAME ATIACHMENT ....................................................................................................... 1
FUNCTIONS
OF
LAME ATIACHMENT ........................................................................................... 1
PARTS ............................................................................................................................................... 1
ILI~"T"AI
11'1\:> I 1"\L.LII'I"-.:'
I
1._11"'
TU~
Inc
I
Al.tr=
1\.TTAr"-UI.aL~IT
LI"\IVIt;:.
/"'\I
I
1"'\VniVI~I't
I
······································•••·········••·•·•••·•••·••••·····••••••···••••••••-.
3-1. Attaching the Positioning Thread Plate ................................................................................... 2
3-2. Attaching the Tension Release Set.. ....................................................................................... 3
· Attaching the Tension Release Set A ..................................................................................... 3
4.
SETIING LAME FILM ....................................................................................................................... 5
5.
ADJUSTING LAME FILM TENSION ................................................................................................. 7
&
EiviBROIDERY
1.
DESIGN DATA .................................................................................................................................. 8
· Attaching the Tension Release Sets
3-3.
Attaching the Roller-type Middle Thread Guide Set ................................................................ 4
4-1. Tension Release 4-2. Tension Release
USING
SetA Sets
LAiviE
............................................................................................................ 6
C, D and
FILrvi
.......................................................................................................... 8
C,
D and E .................................................................... 4
E ........................................................................................... 7
ii
.,
2.
LAME
FILM
AND 3-D EMBROIDERY ............................................................................................... 8
PARTS LIST .........................................................................................................................
End
of Volume
iii
(CG11)
II
NOTICE FOR CHANGE OF CONTENTS
IN
USER'S MANUAL (2000.01) I
We have improved the middle thread guide embroidery, threfore it is now not neccessary to use special middle thread guide, etc., for exclu­sive use. Following the above-mentioned improvement,
of
tents
lame embroidery.
tt
the user's manual as shown below. Please also refer to this notice when you execute
Page
1 Section 2
As
it is unneccessary to use roller-type middle thread guide set and top cover, component
parts
of
lame attachment are shown below.
~PARTS~
Thread stand shaft
of
the embroidery machine to be also used for lame
we
have partially changed the con-
Positioning thread plate
Thread guide A
~Base
\~:7~on
:lease
Tension release
set~
\_Hexagon
M4x6
socket head set screw
Tension release
y
~
*One
type of tension release set
cable tension release type for the individual machine model
Tension release
Tension release Tension release
Tension release
4t
Page
4 Section 3-3
This procedure is unneccessary. (Please proceed to next steps.)
~
is
supplied according to
TMFD, TMFD-C,
set
A
Up
to 12-needle machines TMCE mixed type, TMFN and TMLH mixed type and 15-needle machines
set
C
With
TMEX-C
set
D
TMEX-C
set E TMEX-C
9- and
~Attaching
TME-DC,
TMLG
!5-need!e machine, only machines manufactured
(machines manufatured in August 1999
12-need1e
TMFXII, TMFXII-C
ofTMFXIII,
mixed type, TLFDII,
machines manufactured
the
Roller-type
TMFXIII-C and
Tension release
setE
the
machine model. Appli-
is
shown
below.
TMFXIV
TMEG
in
July 1999 or
or
later)
in
July
1999
or before
Middle Thread
before
Guide
Set"
Loading...
+ 11 hidden pages