Tait T02-00009-0201, T02-00009-0202, T02-00009-0203, T02-00009-0204 Installation Instructions Manual

T02-00009-0201/0202/0203/0204
Hand-Held Control Head Extension Kits
Installation Instructions

The T02-00009-0201/0202/0203/0204 kits can be used to extend the distance between a
hand-held control head and the radio body or a remote interface box. Cables are provided in
lengths of 5ft/1.6m (T02-00009-0201), 10ft/3m (T02-00009-0202), 20ft/6 m (T02-00009-

0203), or 30ft/9 m (T02-00009-0204). A housing unit and gasket encloses the extension
cable socket, and provides additional strain relief and some protection from water and dust
ingress.

Notice Up to ten cables can be con­nected in series, to achieve a maxi­mum distance of 100ft/30 m.
If distances greater than this (up to
200ft/60m) are required, allowances
must be made for the remote speaker
extension. For example, a thicker
speaker cable to reduce audio losses.

extension
cable

gasket

housing
unit

The mounting screws provided for the
housing unit are general purpose, and
may not be suitable for all installa-

self tapping
screws x4
(No. 6 x 0.31in.
(19mm))

tions. It is your responsibility to
choose the most appropriate screw type and length for the mounting location. The max­imum screw diameter you can use with this housing is 0.16in/4.2mm (No. 8 or M4).

Caution When drilling holes in a vehicle, check that drilling at the selected
points (and subsequent fitted screws) will not damage vehicle systems, for
example, existing wiring, petrol tanks, fuel lines, brake pipes or battery cables.

For detailed instructions on how to install grommets and the mounting clip, and for operation
and programming, refer to the instructions provided with the hand-held control head.

1 Determine the best route for the extension cable and mounting position for the housing

unit.

2 Install the extension cable.

a Route the extension cable between the mounting position for the housing unit and

the radio body or remote interface box.

b Drill any holes required for the cable and install suitable grommets or bushings in

the holes.

c Make sure the radio is turned off, then plug the extension cable connector into either

of the RJ45 sockets on the remote blanking control head, or the HHCH port of the
remote interface box.

d Install the extension cable grommet.

© Tait Limited September 2013
www.taitradio.com
402-00095-00

b

c

e

f

d

3 Slide the extension cable socket c into the housing unit.

The socket can slot in the opposite orientation
tion for the connector release clip

4 (Optional) Install the gasket.

a Peel the adhesive backing off one side of the gasket

b Fit that side of the gasket to the housing unit so the screw holes line up.

c Apply pressure until the adhesive holds.

5 Mount the housing unit.

Use one or both of the following mounting methods:

■ If the gasket is installed (step 4), peel the adhesive backing off, place the housing unit

on the mounting surface at the required location, and apply pressure until the adhesive
holds.

The adhesive is optional. If you choose not to use adhesive for mounting, leave the adhe­sive backing on and screw the housing unit and gasket as described below.

f.

b, depending on the most accessible loca-

d.

g

■ Use the four screws provided e, or screws of maximum diameter 0.165 in/4.2mm

(No. 8 or M4), to mount the housing unit. Pre-drill pilot holes of the appropriate
diameter for the screw type and mounting surface before inserting and fastening the
screws.

6 Install the hand-held control head curly cord.

a Slide the hand-held control head connector

unit until the release clip fastens.

b Install the hand-held control head grommet

More Information

Refer to your radio provider for more information about this product.

2 T02-00009-0201/0202/0203/0204 Hand-Held Control Head Extension Kits

f into the connector hole of the housing

g into the housing unit.

© Tait Limited September 2013