T02-00004-0101/T02-00004-0102 Handset
Installation Instructions
Introduction
The T02-00004-0101/T02-00004-0102 handsets improve
the audio quality in noisy environments, and provide the
user with privacy (Private Handset Mode programmed).
The T02-00004-0101 has a 10ft (3m) handset-to-radio
cable, and the T02-00004-0102 has a 20ft (6m) cable. The
locking
cradle
mounting
plate
handset
pushbutton
kits are otherwise identical.
When your radio receives a call and the handset is mounted
in its locking cradle, you can hear the call from your radio’s
internal speaker, and also from any connected remote
speaker.
If you remove the handset from its cradle when you receive
handset-toradio cord
grommet
a call, you can hear the call from your radio’s internal
speaker, from any connected remote speaker, and from the
handset earpiece.
If private handset mode is programmed, the radio’s internal
and external speakers are muted, and the call can only be heard from the handset earpiece.
The handset uses an electret microphone, and comes with the handset-to-radio cord prewired to the handset mounting plate.
If fitting the handset to a TM8200 remote installation that uses components from kit
TMAA03-16, the existing head and body remote interfaces don’t support audio feed to
the microphone socket and therefore can’t be used with the handset. If fitted on the radio,
the TMAA03-16 kit can be identified by radio body interface, which doesn’t have a connector fitted on the right-hand port. For correct operation, the installation should be
upgraded to one of the enhanced remote kits such as TMAA03-19.
Handset Installation
1 Press the push-button and remove the handset from the locking cradle.
2 Disassemble the locking cradle by removing the four locking cradle screws.
3 Drill a hole for the handset-to-radio cord in the chosen mounting surface, and pass the
cord through the hole. The hole must be large enough for the grommet to fit through.
If a smaller hole is required, remove the handset-to-radio cord from the handset PCB
connector, and drill a hole in the mounting surface just large enough to fit the handset to
radio cord.
© Tait Limited December 2013
www.taitradio.com
402-00082-02
Pass the cord through the hole, then reconnect the cord to the handset PCB connector
using the wiring instructions in the diagram “Handset PCB connector wiring”, on
page 2.
4 Screw the handset mounting plate to the required mounting surface. Note that mount-
ing screws are not provided in this kit.
5 Clamp the top part of the locking cradle onto the mounting plate, and secure it with the
four locking cradle screws.
Connecting the Handset to the Radio
Notice The microphone-socket grommet must be installed whenever the handset-to-
radio cord is plugged into the microphone socket. When installed, the grommet has two
functions:
■ to prevent damage to the microphone socket when there is movement of the
handset-to-radio cord, and
■ to ensure that the control head is sealed against water, dust and other
environmental hazards.
1 Plug the handset-to-radio cord into the microphone socket on the radio control head.
2 Slide the grommet along the cord and push two adjacent corners of the grommet into
the microphone socket cavity.
3 Squeeze the grommet and push the remaining corners into position.
4 Check that the grommet is seated correctly in the cavity, as shown in the following dia-
gram.
Correct microphone-socket grommet seating
grommet
control head
Handset PCB connector wiring
Handset PCB
Connector
2violet
3blue
Color Reference
b
c
bc
2 T02-00004-0101/T02-00004-0102 Handset
d e f
8brown
9yellow
10 green
© Tait Limited December 2013
d
e
f
Loading...