tactio INEO-SU2402G User Manual

INEO-SU2402G
Switch 24- Port 10/100TX with
2-Slot MGBIC or 2-Port 1000TE
User’s Manual
FCC Warning
This device has been tested and found to comply with limits for a Class A digital device, pursuant to Part 2 and 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates and radiates radio frequency energy and, if not installed and used in accordance with the user’s manual, it may cause interference in which case users will be required to correct interference at their own expenses.
CE Warning
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
Introduction
The Switch provides 24 10/100Mbps NWAY RJ-45 ports and can support 2 Combo Gigabit Copper/SFP to uplink. It is designed for easy installation and high performance in an environment where traffic on the network and the number of user increase continuously. With the newest Gigabit chip set, 19” Gigabit Ethernet switch can fully support the highest speed without hanging on problem even when Full-Duplex is fully loaded.
The switch also provides automatic crossover detection functionality on each port. It is simple and friendly up-link to another switch without any crossover cable.
The rack-mount size is specifically designed for medium to large workgroups. The Switch can be installed where space is limited; moreover it provides a smooth network migration and easy upgrade a network capacity. The 19” size can be rack-mount into 19” cabinet.
Key Features
Complies with the IEEE802.3 Ethernet,
IEEE802.3u Fast Ethernet and IEEE
802.3ab/z Gigabit Ethernet Standards
Provides 24-port 10/100Mbps + 2 Combo
Gigabit SFP/UTP
19” rack-mount size Non-blocking & Non-head-of-line blocking
full wire speed forwarding
Store-and-forward operation support Embedded 2.75 Mb packet buffer Provides 4K MAC address entry Supports broadcast storm filtering All ports provide Auto-Negotiation and Auto
-MDI/ MDI-X functions
Supports flow control: back pressure for
Half-duplex and IEEE 802.3x for Full-duplex mode
Smart plug & play
Package Contents
Before you start to install this Switch, please verify that your package contains the following items:
One Switch Rack-mount Kit for Rack Installation One AC Power Cord
Note: If any of these items is missing or damaged, please contact your local supplier for a replacement.
Front Panel (LEDs)
LED Indicators of 24-Port 10/100M + 2
Combo Gigabit SFP/UTP Ethernet Switch
LED Status Description No. Of
LED
Power On Power on Power
10/100M On Link 10/100Mbps 24 (1~24)
1000M On Link 1000Mbps 2 (25~26)
off Link 10/100Mbps
Link/ ACT On Link 26 (1~26)
Flashing Data activating 26 (1~26)
Connections
Switch/Hub to this 24-Port 10/100M + 2 Combo Gigabit SFP/UTP Ethernet Switch
This switch provides automatic crossover detection functionality for any port. It is simple and friendly up-link to another switch without any crossover cable.
PC/Other devices to this Ethernet Switch
Via a twisted pair cable straight through, this switch can be connected to PCs, servers and other network devices.
Rear Panel (Power)
AC input (100~240V/AC, 50~60Hz)
Technical Specifications
Standards
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.3ab 1000Bas eT
IEEE 802.3z 1000BaseX
IEEE 802.3x Flow control
Features
Number of Ports:
10/100BaseTX with RJ-45
Connectors: 24
10/100/1000BaseT with RJ-45
Connectors: 2
Combo SFP Open Slots: 2
MAC Address: 4K
Buffer Memory: 2.75 Mb
Method: Store and Forward
Filtering/ Forwarding Rates
1000Mbps port – 1,488,000pps
100Mbps port – 148,800pps
10Mbps – 14,880pps
Transmission Media
10BaseT Cat. 3, 4, 5 UTP/STP
100BaseTX Cat. 5 UTP/STP
1000BaseT Cat. 5E UTP/STP
LED Indicators
Per Port: LINK/ACT
Per Unit: Power
Power Requirement
100~240V/AC, 50~60Hz
Power Consumption
20 Watts (Max)
Dimensions
440 × 220 × 44 mm
(L x W x H)
Weight
3.1 kg
Operating Temperature
0 to 45
Storage Temperature
-20 to 90
Humidity
10 to 90% RH
(non-condensing)
Certifications
FCC Class A, CE
Loading...