Tactical Power Products TPS13-10DC-BD20, TPS13-10DC-B, 13.5Vdc 10A Power, TPS13-10DC, TPS13-10DC-BD10 Installation Manual

13.5Vdc 10A Power Series

MODELS :

TPS13-10DC
TPS13-10DC-B
TPS13-10DC-BD10
TPS13-10DC-BD20
TPS13-10DC-ME
TPS13-10DC-MED10
TPS13-10DC-MED20
TPS13-10DC-MED40

© 2016 The contents of

this manual are copyright
and may not be reproduced
without the written
permission

of Tactical

Power Products Pty Ltd.

Engineered for ACCESS

Installation Manual

DESIGNED & MANUFACTURED

CAUTION

Dangerous internal voltages exceeding

400 Volts - DO NOT REMOVE COVERS !

Dangerous Voltages Inside !

Equipment must be installed & serviced

Do not remove covers

by suitably qualied service personnel in

DANGER
HIGH VOLTAGE

a restricted access area.

No user serviceable parts inside

General

These power supplies are designed for indoor use only.

TPS13-10DC models are high performance, extremely low noise, Dual Channel Switch Mode power supplies offering 13.5Vdc at 10A
continuous.

When operating from mains, these models provide an output of 13.5Vdc ( to power connected equipment) and are configured with a
separate 13.8Vdc battery charging channel. Available battery charge current is 1.4A @ 13.8Vdc (total supply output current 11.4A )

In the event of mains failure, battery voltage is clamped to 13.5Vdc and instantaneously powers the load - this is particularly useful for
powering voltage sensitive loads such as CCTV cameras.. When the mains voltage is restored, batteries are disconnected from the load
and recharging commences automatically.

Output short-circuit and overload protection are provided . Removal of the fault / short circuit condition will return the power supply
to normal operation ( Auto-Reset ).

Model Variants

TPS13-10DC Single 10A Output - Supply only - no cabinet (273L x 145W x 80H )
TPS13-10DC-B Single 10A Output - Medium steel enclosure ( 340W x 436H x 145D mm )

TPS13-10DC-BD10 10 x 1A Outputs - Medium steel enclosure ( 340W x 436H x 145D mm )
TPS13-10DC-BD20 20 x 500mA Outputs - Medium steel enclosure ( 340W x 436H x 145D mm )

TPS13-10DC-ME Single 10A Output - Large steel enclosure ( 482W x 470H x 185D mm )
TPS13-10DC-MED10 10 x 1A Outputs - Large steel enclosure ( 482W x 470H x 185D mm )

TPS13-10DC-MED20 20 x 500mA Outputs - Large steel enclosure ( 482W x 470H x 185D mm )
TPS13-10DC-MED40 40 x 250mA Outputs - Large steel enclosure ( 482W x 470H x 185D mm )

Connection

Single Output Models Multiple Output Models

10-way removable terminal block provides the following:
( See over the page for a layout )

* 13.5Vdc Output
* 13.8Vdc Output for SLA (Sealed Lead Acid) Batteries
* Battery Test load (not used on this model)
* AC OK Relay Output ( SPST )
* Battery Fault/Low Battery Relay Output ( SPST )

13.5Vdc Output is via individually fused outputs ( 10, 20 or 40 )

10-way removable terminal block provides the following:
( See over the page for a layout )
* 13.8Vdc Output for SLA (Sealed Lead Acid) Batteries
* Battery Test load (not used on this model)
* AC OK Relay Output ( SPST )
* Battery Fault/Low Battery Relay Output ( SPST )

Caution when handling batteries:

TPS13-10DC_Rev B.pdf

www.tacpower.com.au

LAYOUT

Multi-Output Models TPS13-10DC Module Face
( e.g. TPS13-10DC-BD10 )

A

B

C

D

E F G H I

J K L

M N

Output Terminals ( Multi Output models only )

A

Individual Circuit Status LEDs ( Multi Output Models )

C

AC Mains OK Output ( COM / NC )

E

Not used in this model

G

- Output 13.5Vdc + ( Connect to load or PDM )

I

Battery Test Fail LED ( Red ON = Fail )

K

AC Mains OK LED ( Green ON = OK )

M

240V IEC Mains Socket

O

DESIGNED & MANUFACTURED

O

PDM Input ( Multi Output models only ) - “ I ” below

B

Individual Circuit Fuses ( Multi Output models only )

D

Battery Low / Fault Output ( COM / NC )

F

- Battery + (Connect Sealed Lead Acid Battery)

H

Not used in this model

J

Battery Fuse Fail LED ( Red ON = Fail )

L

Reverse Battery LED ( Red ON = Fail )

N

Compliance / Date of Manufacture Label

P

Rear View

P

TPS13-10DC_Rev B.pdf

www.tacpower.com.au

13.5Vdc
10A Series

®

Specications : ( In the interests of product improvement, Tactical reserves the right to change specifications without notice)

10DC 10DC-B 10DC-BD10 10DC-BD20 10DC-ME 10DC-MED10 10DC-MED20 10DC-MED40

Output Voltage 13.5 Vdc

Output Current 10A Continuous

Output Channels 1 1 10 20 1 10 20 40

Output per Channel 10A 10A 1A 500mA 10A 1A 500mA 250mA

Input Voltage 240 V ac ( +6% / -10% ) 50Hz

Input Current 1.4A @ full load

Input In-Rush Current <20A ( 250 C cold start up )

Battery Charger 13.8Vdc / 1.4A

Low Battery Indicator 1 x SPST relay & Red LED

AC Input Indicator 1 x SPST Relay & Green LED

Weight <2Kg <5Kg <5Kg <5Kg <12Kg <12Kg <12Kg <12Kg

Dimensions

Efficiency 83% at rated load

Overload Protection Constant current limiting, short circuit shutdown, auto recovery

Load Regulation < 1% from open to full load

Line Regulation < 0.2%

Output Ripple 25mV p-p @ full load

Working Temperature 0 - 500 C

273L x 145W

x 80H

340W x 436H x 145D mm 482W x 470H x 185D mm

Revision B

Safety Standards AS NZS 60950:2011

EMC Standards AS/NZS CISPR 11:2004 ( Class B Conducted and Radiated )

www.tacpower.com.

Securing Your Power Needs

®

Now and into the Future . . .

Tel: [phone] PO Box 90 Kurrajong NSW 2758 [e-mail]

Designed & Manufactured