Tactical TPS24-3DC-B, TPS24-3DC-MED10, TPS24-3DC-ME, TPS24-3DC-MED20, TPS24-6DC Installation Manual
...
24Vdc 3A & 6APower Series
MODELS :
TPS24-3DC
TPS24-3DC-B
TPS24-3DC-ME
TPS24-3DC-MED10
TPS24-3DC-MED20
TPS24-6DC
TPS24-6DC-B
TPS24-6DC-ME
TPS24-6DC-MED10
TPS24-6DC-MED20
© 2012 The contents of
this manual are copyright
and may not be reproduced
without the written
permission of Tactical
Power Producst Pty Ltd.
Installation Manual
DESIGNED & MANUFACTURED
CAUTION
Dangerous internal voltages exceeding
400 Volts - DO NOT REMOVE COVERS !
Dangerous Voltages Inside !
Equipment must be installed & serviced
Do not remove covers
by suitably qualied service personnel in
DANGER
HIGH VOLTAGE
a restricted access area.
No user serviceable parts inside
General
These power supplies are designed for indoor use only.
TPS24-DC Series models are high performance, extremely low noise, Dual Channel Switch Mode power supplies offering 24Vdc at 3A or
24Vdc 6A (model dependant).
When operating from mains, these models provide an output of 24Vdc ( to power connected equipment) and are configured with a
separate 27.6Vdc battery charging channel. Available battery charge current is 700ma @ 27.6Vdc (approx) for TPS24-3DC Models (total
output 3.7A) & 1.4A @ 27.6Vdc (approx) for TPS24-6DC Models (total output 7.4A) In the event of mains failure, battery voltage is clamped
to 24Vdc and instantaneously powers the load. When the mains voltage is restored, batteries are disconnected from the load and
recharging commences automatically.
Output short-circuit and overload protection are provided . Removal of the fault / short circuit condition will return the power supply
to normal operation ( Auto-Reset ).
Model Variants
TPS24-3DC Single 3A Output - Supply only - no cabinet (273L x 145W x 80H )
TPS24-3DC-B Single 3A Output - Medium steel enclosure ( 340W x 436H x 145D mm )
TPS24-3DC-ME Single 3A Output - Large steel enclosure ( 482W x 470H x 185D mm )
TPS24-3DC-MED10 10 x 300mA Outputs - Large steel enclosure ( 482W x 470H x 185D mm )
TPS24-3DC-MED20 20 x 150mA Outputs - Large steel enclosure ( 482W x 470H x 185D mm )
TPS24-6DC Single 6A Output - Supply only - no cabinet (273L x 145W x 80H )
TPS24-6DC-B Single 6A Output - Medium steel enclosure ( 340W x 436H x 145D mm )
TPS24-6DC-ME Single 6A Output - Large steel enclosure ( 482W x 470H x 185D mm )
TPS24-6DC-MED10 10 x 600mA Outputs - Large steel enclosure ( 482W x 470H x 185D mm )
TPS24-6DC-MED20 20 x 300mA Outputs - Large steel enclosure ( 482W x 470H x 185D mm )
Connection
Single Output Models Multiple Output Models
10-way removable terminal block provides the following:
( See over the page for a layout )
* 24Vdc Output
* 27.6Vdc Output for SLA (Sealed Lead Acid) Batteries
* Battery Test load (not used on this model)
* AC OK Relay Output ( SPST )
* Battery Fault/Low Battery Relay Output ( SPST )
24Vdc Output is via individually fused outputs ( 10 or 20 )
10-way removable terminal block provides the following:
( See over the page for a layout )
* 27.6Vdc Output for SLA (Sealed Lead Acid) Batteries
* Battery Test load (not used on this model)
* AC OK Relay Output ( SPST )
* Battery Fault/Low Battery Relay Output ( SPST )
Caution when handling batteries:
Before connecting two 12V SLA batteries in series to this power supply, ensure both are fully charged to 13.8V, this will ensure the batteries are charged
evenly via the 27.6v charging circuit. Excercise care when terminating and connecting batteries. Mishandling or short circuit of SLA batteries can cause
severe damage, burns and fire.
TPS24-DCSeries_Rev K.pdf
www.tacpower..com.au
LAYOUT
Multi-Output Models TPS24-6DC Module Face
( e.g. TPS24-6DC-MED10 )
A
B
C
D
E F G H I
J K L
Output Terminals ( Multi Output models only )
A
Individual Circuit Status LEDs ( Multi Output Models )
C
AC Mains OK Output ( COM / NC )
E
Not used in this model
G
- Output 24Vdc + ( Connect to load or PDM )
I
Battery Test Fail LED ( Red ON = Fail )
K
AC Mains OK LED ( Green ON = OK )
M
240V IEC Mains Socket
O
M N
PDM Input ( Multi Output models only ) - “ I ” below
B
Individual Circuit Fuses ( Multi Output models only )
D
Battery Low / Fault Output ( COM / NC )
F
- Battery + (Connect Sealed Lead Acid Batteries)
H
Not used in this model
J
Battery Fuse Fail LED ( Red ON = Fail )
L
Reverse Battery LED ( Red ON = Fail )
N
Compliance / Date of Manufacture Label
P
DESIGNED & MANUFACTURED
TPS24-DCSeries_Rev K.pdf
Rear View
P
O
www.tacpower.com.au
Specications : ( In the interests of product improvement, Tactical reserves the right to change specifications without notice)
24Vdc
3A & 6A Series
3DC 3DC-B 3DC-ME
Full Model Number
Output Voltage 24Vdc
Output Current 3A 6A
Output Channels 1 10 20 1 10 20
Output per Channel 3A 300mA 150mA 6A 600mA 300mA
Input Voltage 240 V ac ( 215V - 255V ) 50Hz
Input Current 0.8A at full load 1.6A at full load
Input In-Rush <20A ( 25˚ C cold start up )
Battery Charger 27.6Vdc / 0.7A 27.6Vdc / 1.4A
Low Battery Indicator 1 x SPST Relay & Red LED
AC OK Indicator 1 x SPST Relay & Green LED
Weight < 2Kg < 5Kg < 12Kg < 2Kg < 5Kg < 12Kg
Dimensions (mm)
TPS24-3DC
273L x 145W
x 80H
TPS24-
3DC-B
340W x 436H
x 145D
TPS24-3DC-METPS24-3DC-
482W x 470H x 185D
3DC-
MED10
MED10
3DC-
MED20
TPS24-3DC-
MED20
6DC 6DC-B 6DC-ME
TPS24-6DC
273L x 145W
x 80H
TPS24-
6DC-B
340W x 436H
x 145D
TPS24-6DC-METPS24-6DC-
6DC-
MED10
MED10
482W x 470H x 185D
MED20
TPS24-6DC-
6DC-
MED20
Efficiency 80% Typical
Overload Protection Constant current limiting, short circuit shutdown, auto recovery
Load Regulation < 1% from open to full load
Line Regulation < 0.2%
Output Ripple <50 mVp-p @ full load
Working Temperature 0 - 45 ˚ C
Revision K
Safety Standards AS NZS 60950.1:2003
EMC Standards AS / NZS CISPR 11:2004 Class B (Conducted & Radiated)
www.tacpower.com.
Securing Your Power Needs
®
Now and into the Future . . .
Tel: 1300-822-769 PO Box 90 Kurrajong NSW 2758 sales@tacpower.com.au
Designed & Manufactured
Loading...