Tacony TRUVOX MW340/PUMP/B User Manual

TM
TRUVOX
INTERNATIONAL
--- A TACO NY COMPANY ---
I
ORIGINAL INSTRUCTIONS
CAUTION - READ THESE INSTRUCTIONS BEFOREUSING
Battery Multiwash 340/Pump
MVV340/PUMP/B
I
-------
USERMANUAL EN MANUEL D'UTILISATION FR GEBRAUCHSANLEITUNG DE
03-8324-0000 Issue3 02-15
IMPORTANT
BEFORE USE READ THESE INSTRUCTIONS AND RETAIN FOR FUTURE REFERENCE
Introduction The following instructions contain important information about the machine and safety advice for the operator. Equipment must be operated, serviced and maintained in accordance with the manufacturer's instructions. If in doubt contact the supplier of your machine.
Read all instructions before using
the machine
Product information The Multiwash floor cleaning machines are designed for use on smooth, even floors in indoor areas. They can be used on most floor surfaces including short-pile carpet, wood, PVC, rubber and stone. They should not be used on rough uneven surfaces. This machine is for indoor use only. The machine is intended for commercial use, for example in hotels, schools, hospitals, factories, shops, offices, rental businesses and otherthan normal housekeeping purposes.
Technical Specifications
Model Multiwash Charging Voltage AC (-)/
Frequency
Battery voltage V 24 Motor Power W 300 Continuous runtime mins 50
Productivity rate Solution tank capacity litres 4
Brush/cleaningwidth cm 34
Brushspeed rpm 400
Brush pressure Sound pressure level dB(A) 66
Dimensions (L x W x H) with handle
Weight kg 22 Warranty 1 year
Noise levels measured at a machine and 1.6 metres above floor, when washing a hard floor. Measurements recorded using a hand held meter.
Handle vibration does not exceed 2.5 m/s2,when operating on a smooth hard surface.
Above dimensions are approx. Since the company's policy is to continuously improve the product, there could be chanqes without prior notice.
EC DECLARATION OF CONFORMITY Machine Type: Floor Cleaning Machine Model: MW340/Pump/B... This machine is in conformity with the following EU directives:
Machinery Directive: 2006/42/EC
The EMC Directive: 2004/108/EC Applied harmonised standards:
EN60335-1, EN60335-2-72, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3, EN62233
V/ Hz
m2/h
g/cm2
cm
distance of 1 meter from
Battery
340/Pump
100-240/ 50 - 60
930
88
37.8 x 44 x 111.4
Waste Electrical&Electronic Equipment (WEEE)
)t
Do not dispose of this device with unsorted waste. Improper disposal may be harmful to the environment and human health. Please refer to your local waste authority for information on return and collection systems in your area.
-
IMPORTANT SAFETY ADVICE The safety information described in this manual provides basic precautions and supplements standards in force in the country where the machine is used.
~ shock or fire.
1. This machine must only be used for the manufacturer's
2. The machine must be unpacked and assembled in
3. Operators must be fully trained in the use of the machine
4. Operators should be physically capable to manoeuvre,
5. Operators should be able to recognise unusual
6. Only genuine accessories and spare parts provided with
7. Do not use without filters in place.
8. Do not modify the machine from its original design.
9. Only use the machine on firm level surfaces. DO NOT
10. DO NOT use on rough uneven surfaces e.g. industrial or
11. DO NOT use outdoors e.g. on patios, decks or rough
12. WARNING Do not fill machines with water hotter than
13. DO NOT use diesel/petrol or corrosive detergents to
14. This machine is not intended for use by persons
15. Keep children and unauthorised persons away from the
16. The machine must be kept clean and in good condition
This symbol warns the operator of hazards and unsafe practices which could result in severe
personal injury or death.
I.\!_
WARNING - to reduce the risk of injury, electric
approved application as described in this manual. accordance with these instructions before connecting to
the electrical supply. in accordance with these instructions, able to perform
regular user maintenance and the correct selection of accessories.
transport and operate the machines. operation of the machine and report any problems. the machine or those approved by the manufacturer
should be used. All repairs must be performed by a qualified service agent.
use on a gradient or more than 2% slopes. coarse concrete surfaces. surface. 40QC wash floors, even if diluted. (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the machine by a person
responsible for their safety. machinewhen in use. Do not use as a toy. with regular inspections of the battery charging lead and
plug for signs of any damage. If any parts are damaged they shall only be replaced by an approved part by the manufacturer, its service agent or a similar qualified person in order to avoid a hazard.
ELECTRICAL HAZARD
Truvox International Limited Unit C (East), Hamilton Business Park, I'-"\.· Manaton Way, Botley Road, Malcolm Eneas Hedge End, Southampton, Operations Manager S030 2JR, UK Southampton,26/03/2014
l ).~.
2
17. CAUTION - This machine is for dry indoor use only and should not be used or stored outdoors in wet conditions.
18. DO NOT usewhere hazardous dust is present.
19. DO NOT use in an explosive atmosphere.
20. DO NOT pick up or use near flammable or combustible fluids, hazardous dusts or vapours.
21. CAUTION - If it is suspected that there is hazardous dust
or flammable materials stop cleaning the area immediately and consult your superior.
22. DO NOT use to clean up any burning or lighted materials such as cigarettes, matches, ashes or other combustible objects.
23. Take care when using a machine near the top of stairs to avoid overbalancing.
24. DO NOT put any object into openings. DO NOT use with any opening blocked; keep free of dust, debris and anything that may reduce airflow.
25. DO NOT cover the machine when in use.
26. Keep hair, loose clothing, hands, feet and all other parts of the body away from openings and moving parts.
27. Do not operate the machine when connected to the mains electrical supply.
28. DO NOT use if it has been damaged, left outdoors or dropped in water.
29. DO NOT run the machine dry, as this could damage the floor surface or the machine itself.
30. Never use excessive foaming or highly corrosive cleaning solutions.
31. WARNING Unless you are charging the machine; always removethe plug from the socket outlet.
32. Do not charge the machine with a damaged battery charging lead or plug, or after the machine malfunctions or is damaged in any way. Contact an authorised Service Agent for repair or adjustment.
33. Only replace the supply cord with the type specified in the instruction manual.
34. This machine should always be connected to a fully earthed power supply of the right voltage and frequency.
35. DO NOT leave machine running unattended.
36. When unplugging, pull the plug, not the charger supply cord.
37. Unless charging, the plug of the charger supply cord must be removed from the socket-outlet when not in use and before commencing cleaning of the machine or undertaking maintenance operations.
38. DO NOT pull or carry by the charger supply cord. DO NOT use cord as a handle, close door on cord or pull cord around sharp edges or corners.
39. WARNING: Keep the charger supply cord clear of moving parts.
40. DO NOT kink or twist the charger supply cord and keep cord away from heated surfaces.
41. DO NOT operate switches or touch the mains plug with wet hands as this may cause electric shock.
Safe Disposal of Batteries
The batteries must be neutralised through an approved secondary treatment facility prior to disposal as waste. The battery can be recycled at an authorised facility, through a licensed waste carrier.
CONTROLS ON THE MACHINE
The operating controls are located on the handle (1) and on the side of the machine. Please refer to
Solution discharqe handle
1.
2. Solution tank 6. Pedal
3. Recovery tank 7. Transport/working mode
4. Nozzle
Transporting the machine
Incorrect lifting techniques may result in personal injury. We advise that the manual handling regulations are followed. Carefully wrap the charger supply cord and store in dry indoor location. Do not expose the machine to rain or moisture.
When transporting the machine ensure that all components, tanks and removable parts are securely fastened, and that the supply cord and plug are not trailing.
paqa
5. Main brush
8. Brush pressure
1.
When transporting the machine the handle should be locked in the upright position.
Take extreme care when moving the machine up or down steps or stairs.
Brush Identification
Red, Blue, White and Yellow brush buttons are packed with the machine. Simply plug the buttons into the hole in the brush as shown. Clear identification, by colour coding, helps prevent cross contamination.
Storage
Always switch off, empty, wipe down and dry the machine after use.
Both the solution and recovery tanks should be emptied and flushed out with clean water to ensure the seals and
pumps are free from any cleaning detergents.
Store the machine in a dry indoor area only.
Maintenance
Lh
IMPORTANT - All other servicing and repairs should only be performed by a Truvox engineer or Authorised Service Agent. IMPORTANT - Should the machine fail to operate please refer to the fault diagnosis section in the back of this instruction manual. If the problem / remedy is not listed please contact Truvox Customer Service Department for rapid attention.
The machine requires minimum maintenance apart from the following checks by the operator prior to use:
DO NOT use aggressive detergents, acid, lye etc. during cleaning and washing and take particular care with electrical parts.
Supply cord - Regularly inspect sheath, plug and cord anchorage for damage or loose connection. Only replace the supply cord with the type specified in these
Brushes - For maximum life, wash the brushes regularly.
the brush so that the bent bristles are automatically straightened.
Wiper Blade - After years of use the wiper blade may wear. If this occurs the water collection performance will decrease. It should be replaced by an authorised service agent.
Solution feed filter (Pump) - The filter prevents clogging of the spray nozzle and should be periodically cleaned.
Nozzle maintenance (Pump) - If the spray of the nozzle
UK Model only
The charger cord is equipped with a 13 amp fuse. If replacing fuse, use a 13 amp fuse confirming to BS1362. Do not usethe machine if fuse cover is missing.
After sales service
Truvox machines are high quality machines that have been
tested for safety by authorised technicians. It is always
apparent that after longer working periods, electrical and mechanical components will show signs of wear and tear or ageing. To maintain operational safety and reliability the following service interval has been defined: Every year or after 250 hours. Under extreme or specialised conditions and/or insufficient maintenance, shorter maintenance
WARNING - Before undertaking maintenance
1
operations or adjustments switch off machine
and unplug from the electricity supply.
instructions. Ensure machine is in Transport mode when not in use.
Store additional brushes in a vertical position to avoid bending of bristles. Check for permanent bending of bristles in a particular direction. This may occur if the machine is operated for several days without removing the brushes, which is not recommended. If this occurs, reverse
Use pressurised air/water for cleaning. becomes blocked, slide the nozzle cover off and remove
nozzlewash in clean water and clean using a pin and refit.
3
intervals are necessary. Use only original Truvox spare parts. Use of other spare parts will invalidate all warranty and liability claims. Should you require after sales service please contact the supplier from whom you purchased the machine, who will arrange service. Repairs and servicing of Truvox products should only be performed by trained staff. Improper repairs can cause considerable danger to the user.
Guarantee
Your product is guaranteed for one year from the date of original purchase, or hire purchase, against defects in materials or workmanship during manufacture. Within the guarantee period we undertake at our discretion, to repair or replace free of charge to the purchaser, any part found to be defective, subject to the following conditions:
CONDITIONS
1. Claims made under the terms of the guarantee must be supported by the original invoice/bill of sale issued at the time of sale, or the machine Serial No.
2. For claims under this guarantee contact the supplier from whom you purchased the product who will arrange the appropriate action. Do not initially return the product as this could result in transit damage.
Recommended Spares&Accessories
Part No. Item
90-0130-0000
90-0131-0000
90-0132-0000 90-0089-0000 90-0090-0000 05-3395-0500 90-0556-0000 90-0588-0000 90-0585-0000 90-0586-0000
Standard brushes - black (2 required)
Soft brush - grey (2 required) rubber, vinyl, PVC (Maintenance cleaning); short pile carpet,
Side brush - black (1 required) For up-to-the-edge cleaning Hard brush - blue (2 required) To suit individual floor conditions, smooth concrete Escalator brush - blue (2 required) For use on escalators Trolley Foreasier transport Battery Pack Charger only Charger cable EU Charger cable UK
3. Neither Truvox nor its distributor shall be liable for any incidental or consequential loss.
4. This guarantee is governed by the laws of England.
5. This guarantee does not cover any of the following:
Periodic maintenance, and repair or replacement of parts due to normal wear and tear.
Damage caused by accident, misuse or neglect, or the fitting of other than genuine Truvox parts.
Defects in other than genuine Truvox parts, or repairs, modifications or adjustments performed by other than a Truvox service engineer or authorised service agent.
Costs and risks of transport relating directly or indirectly to the guarantee of this product.
Consumable items such as, brushes, drive discs, filters and vacuum skirts.
This guarantee does not affect your statutory rights, or your rights against the supplier arising from their sales or
purchase contract. Truvox International Limited policy is
one of continual product development and we reserve the
right to alter specifications without prior notice
Usage
All natural stone floors, ceramic, mosaic, wood, profiled rubber, vinyl, PVC (First time cleaning); smooth concrete All natural stone floors, ceramic, mosaic, wood, profiled
marble qranite
Battery Status
Machine Operation
LED Status Discharging
GREEN Fully charged AMBER Battery approaching low charge AMBER FLASHING Battery approaching cut off limit
RED
Lowcharge / cut off Motortemperature exceeds limits
RED FLASHING Batterycut off limit reached
4
Fault diagnosis The following simple checks may be performed by the operator:
Trouble Display Reason Remedy
Machine fails to start
-no power
Brushes not rotating
Machine fails to pick up water from the floor
Machine fails to spray solution onto the floor
Machine only sprays NA when handle in upright position
Drum is rotating, but
brushes are not
Drum not rotating
Motor makes a humming noise but does not turn
No LED Display
LED flashes in
RED
NA
NA
NA
NA
NA
Transport working knob is in Change to operating position bottom position
Mains switch on battery is Switch to on position on off position
Motor overload protector has tripped move allowing brushes to touch the floor, if
Micro switches are faulty open circuit
Battery low voltage Charge the battery
Motor overheated Wait 20 minutes and restart
Worn brushes
Damaged lip on recovery tank
Broken lugs on recovery tank
Drum not revolving
Bridge fitted wrong way on machine or springs broken
Blocked jet
Blocked inline filter
Faulty pump
Blocked filter or faulty valve in solution tank
Faulty pump micro switches
Damaged or broken pump on/off cord
Loose lower handle bolts Tighten lower handle bolts
If one or both brushes are not turning, stripped gears in gear box
Plastic gear inside rim of drum sheared
Drum sprocket bearing seized
Build up of dirty hair etc. around bridge springs and build up
Plastic gears in gear box stripped
Drum rubber sleeve loose on drum
Motor seized up
Faulty motor windings
When handle is lowered transport wheels
transport wheels don't move when handle is lowered remove wheels and shafts and clean.
Replace brush, lip, lugs or springs
Fit bridge the correct way
Clean jet or inline filter
Check cord
Clean drum and bearings and remove dirt
Contact service agent
* If the fuse blows several times, the machine should be checked by an authorises Service Agent
5
AVERTISSEMENT - LlSEZ ATENTIVEMENT CETTE NOTICE AVANT O'UTILISER LA MACHINE
ET CONSERVEZ-LA POUR VOUS Y REFERER ULTERIEUREMENT
Informations generales Ce manuel contient des informations importantes sur la machine et des avis de sscurite pour l'opsrateur. l.'equipernent doit fonctionner, etre en service et entretenu contormernent aux instructions du fabricant. En cas de doute, contactez votre fournisseur.
Lire attentivement toutes les
instructions avant toute utilisation.
Informations sur Ie produit Les machinesalaver les sols Multiwash sont concuss pour etre utilissesal'interieur, sur des sols lisses et homoqsnes. Elles peuvent etre utilisses sur la plupart des revetements de sols, y compris les moquettesapoils ras, les planchers en bois, Ie PVC, Ie caoutchouc et la pierre. Elles ne doivent pas etre utilisees sur des surfaces rugueuses irrequlieres, Cette appareil n'est reserve qu'a une utilisation en interieur.. Cette machine est dsstinee a I'utilisation commerciale, par exemples hotels, eccles, hopitaux, usines, magasins, bureaux, societes de location ou utilisation domestique.
Specifications techniques Model
Voltage de rechargement AC
H
I Frequence
Voltage d.c V 24 Puissance Moteur W 300 Utilisation ininterrompue mins 50 Productivite rnvh 930
Capacite du reservoir de solution
Largeur de brosse cm 34 Vitesse de brosse Pression de brosse Niveau sonore dB(A) 66
Dimensions (L x W x H) with handle
Poids kg 22 Garantie 1 year
Les niveaux sonores sont rnasurasaune distance d'1 metre par rapportala machine et de 1,6 metres au-dessus du sol pendant Ie lavage d'un revetement duroLes mesures sont enregistrees par un appareil portatif.
La vibration du manche ne depassepas 2,5 rn/s>lors d'une utilisation sur une surface dure et lisse.
Les dimensions ci-dessus sont approximatives. Truvox poursuivant une politique d'arnelioration continue, des changements peuvent etre apportss sans avis prealable,
EC DECLARATION OF CONFORMITY Machine Type: Floor Cleaning Machine Model: MW340/Pump/B... This machine is in conformity with the following EU directives:
Machinery Directive:
The EMC Directive:
Applied harmonised standards:
EN60335-1, EN60335-2-72, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3, EN62233
Truvox International Limited H ~
Unit C (East), Hamilton Business Park,' Manaton Way, Botley Road, Malcolm Eneas Hedge End, Southampton, Operations Manager S030 2JR, UK Southampton, 26/03/2014
VI Hz
litres 4
trs/mn
g/cm2
cm
Battery Multiwash
340/Pump
100-240 I 50 - 60
400
88
37.8 x 44 x 111.4
2006/42/EC 2004/108/EC
Dechets
(DEEE)
:a
_ dechets pour obtenir des informations sur les
systsrnes de retour et de collecte dans votre secteur. IMPORTANTES CONSIGNES DESECURITE
Les consignes de sscurite dscritas dans ce manuel proviennent des consignes de sscurita standards en vigueur dans Ie paysou I'appareil est utiliss.
1. Cet appareil dans les conditions et destinations
2. Toutes les pieces doivent etre positionnees
3. Afin de pouvoir procederaune utilisation de la machine
4. Les opsrateurs doivent etre physiquement capables de
5. Operators should be able to recognise unusual operation
6. Seuls les accessoires et pieces detachees d'origine
7. Ne pas utiliser sans filtres
8. Ne pas modifier I'appareil de sa configuration initiale
9. Utilisez la machine sur des surfaces planes et stables
10. N'UTILISEZ PAS la machine sur des surfaces
11. N'UTILISEZ PAS la machine en sxterieur, par exemple
12.AVERTISSEMENT - Ne remplissez pas la machine
13. N'UTILISEZ PAS de diesel/d'essence ou de detergents
14. Cet appareil n'est pas concu pour etre utilisa par des
15. Tenir les enfants et toutes les personnes non autorisees
16. La machine doit etre nettoyea regulierement et qardea
d'Equipements Electriques et Electroniques Ne pas jeter cet appareil avec les dechets non
recyclables. Toute elimination inappropriee peut
etre nocive pour I'environnement et la sante
humaine. S'adresser aux agences locales de traitement des
Ce symbole alerte I'utilisateur sur les dangers eventuels et les pratiques imprudentes pouvant entraTnerdes blessures graves voire la mort. ATTENTION - Afin de redulre Ie risque d'incendie, electrocution ou de blessure:
preconisess par la fabricant comme decrites dans ce manuel.
contormernent aux instructions avant utilisation de la machine.
conformeaces instructions, les opsrateurs doivent avoir suivis une formation complete, etre capables de realissr les operations d'entretien ainsi que de proceder au choix correct des accessoires.
manceuvrer,detransporter et de faire fonctionner les machines.
of the machine and report any problems. prsvus pour cette machine ou approuvss par Iefabricant
doivent etre utilises, Toute reparation doit etre effectuee par un agent agree par Iefabricant.
uniquement. N'UTILISEZ PAS la machine sur une pente dont I'inclinaison est supsrieurea2
rugueuses irrequlieras telles que des sols en bston industriel.
dans une cour, sur un pont ou des surfaces irrequlieres, avec de I'eauaplus de 400C. corrosifs pour nettoyer les sols. personnes (et notamment des enfants)acapacitss
motrices, sensorielles ou intellectuelles reduites, ou manquant d'experiencs et de connaissances, excepts s'ils sont supervises ou formesaI'utilisation de I'appareil par une personne responsable de leur sscurite.
a
distance de la machine quand celle-ci est en fonctionnement. Ne pas laisser I'appareil etre utilisa comme un jouet.
dans les meilleurs conditions de fonctionnement par une inspection reguliere du cable d'alimentation et d'interrupteur. Toute piece defectueuse doit etre rernplacee par une piece d'origine agreee par la fabricant, Ie reparateur agree ou toute personne habilitea
a
intervenir sur I'appareil.
RISQUE ELECTRIQUE
%.
6
Loading...
+ 14 hidden pages