SZ DJI TECHNOLOGY RE7001402 User Manual

Download

Page 1

Compliance Version: The PHANTOM 2 VISION+ remote controlleris compliant with CE and FCC (see the

Operating Mode

Mo de 1

Mo de 2 : The right stick is mapped to throttle channel.

The range extender and mobile device holder is already mounted on the remote controller. Twist mobile

device holder to face outwards and fix in position to prepare for mobile device installation.

It is recommended not to use oversized mobile devices (e.g. iPad), which cannot be placed into the

Mobile Device Holder.

[1]

[2]

[4]

[3]

[8] [9]

[11]

[6]

[7]

[5]

[10]

[1]

[11]

Antenna

Battery Compartment (On the back)

1. Install the four AA Batteries into the battery compartment on the back of the remote controller

2. Set the S1 and S2 switches to the upper most position and all sticks at mid-point.

5Preparing the Remote Controller

The PHANTOM 2 VISION+ remote controlleris a wireless communication device that uses the 5.8GHz frequency

band. The link between the remote controller and aircraft isalready established before delivery.

The remote controller default is set to Mode 2 and CE compliance before del iv er y. Both the operating mode and

compliance version can be configuredin PHANTOM RC Assistant Software. Please referto <PHANTOM

RCAssistant> and <ComplianceConfiguration> for details.

FCC ID) regulations.

: The remote controller is div i ded to Mode 1 and Mode 2 according to different channel

mappings.

: The left stick is mapped to throttle channel.

5.1The Remote Controller

[2]

Carrying Handle

[3]

SwitchS1

[4]

Switch S2 (Reserved)

[5]

Joystick(J1: Roll [left&right], J2: Pitch [front&back])

[6]

Joystick(J3: Throttle [up&down], J 4: Ya w [rotation])

[7]

5.2 Power on the Remote Controller

according to the negative andpositive po les .

Neck Strap Attachment

[8]

Power Switch

[9]

Power Indicator

[10]

RC Assistant Port(Micro-USB Port)

Page 2

3. Toggle the power switch to right end to switch on the power.

4. There is a power on indicator beep. If the remote controller is set to be CE compliant, then there will be

indicating the remote controller and receiver are binding. Once binding is completed, the power

indicator will change to a solid green.

If the low voltage warning alert sounds(refer to the <Remote Controller Power Indicator Status

Dispose the depleted batteries safely.

Power indicator

Sound

Remote Controller Sta te

None

Functioning normally.

None

Establishing a link between the remote controller and the receiver.

B-B-B……

Low voltage (at 3.9V-4.5V), should replace the batteries immediately.

BBBB

Low voltage (lower than 3.9V). The remote controller will automatically

power off. Replace the batteries immediately.

B-B-B……

The remote controllerwill give a visual indication of an alarm after 15

operating of the remote controller.

The remote controllerwill blink the LED and sound an alert when the voltage drops below3.9V and

voltage warning(3.9V-4.5V) occurs.

one beep while the FCCcompliant version will emit 2 beeps. The power indicator blinks greenquickly

（1）

Information>), please replace batteries as soon as possible.

（2） For long term storage, be sure to remove the batteries from the remote controller.

（3）

5.3 Remote Controller Power Indicator Status Information

minutesof non-operation. The alarm status will go awayonce you start

automatically power off after 3 seconds. This process will repeat even if you power cycle the remote

controller. If this low voltage warning occurs during flight, the remote controllerwill automatically

power off causing the aircraft to enter Failsafe mode which cannot be interrupted (refer to <Failsafe

Function> section for details). It is strongly recommended to replace batteries immediatelyif the low

Page 3

5.4 AntennaOrientation

Try to keep the antenna pointingskyward, perpendicular to the ground, in order to achieve the maximum

communication range during flight.

The rem ote controller’s antenna should be pointing skyw ard w ith no obstacles in the w ay. O therwise, the F a ils a fe fu n c t io n m a y in it ia liz e prem aturely during flight. The M obile D evice and Range Extender should not block the antenna.

Stick Neutral/ mid point:Control sticks of theremote controller are placedatthe central position.

Move the Stick:The stick of remote controller is pushed away from the central position.

Remote Con tr o lle r

(Mode 2 )

Aircraft

nose direction）

Operation deta ils

The throttle stickcontrolsthe aircraft elevation.

that you push the throttle stickgently to prevent the

aircraft from sudden and unexpectedelevation.

5.5 Remote Controller Operation

The remote controller default is set to Mode 2 before delivery, follow descriptions takes Mode 2 for example.

（

Push the stickup and the aircraft will ascend.

Pullthe stickdown and the aircraft will descend.

The aircraft will automatically hover and hold i ts

height when bothsticksare centered.

Push the throttle stickupward beyondthe centered

(neutral) position to take off the aircraft. We suggest

Page 4

The yaw stickcontrols the ai rc ra ft rudde r.

Push the stickleft and the aircraft will ro tat e counter

command stick results in fasteraircraft ro tat ion

ve lo ci ty.

The pitchstickcontrols the aircraft’sfront & back

pitch.

result in a largerpitch angle (maximum is 35˚) and

faster flight velocity.

The rollstick controls the aircraft le ft &rightpitch.

Push the stickleft and the aircraft will pitchand fly

result in a largerpitch angle (maximum is 35˚) and

faster flight velocity.

S1 is for compass calibration. Toggle the S1 from

In Naza-M mode, the S1 switch is used to switch

control mode and compass calibration.

S2 is used to record Home point manually. After a

Home point is automatically recorded, quickly

home point of PHANTOM 2 VISION+.

InNaza-M m ode , S2 is involved in IOC function.

(1) For ‘ Ready to Fly’ the aircraft will hover (hold a stable horizontal position) when all sticks are

released.

clock-wise.

Push the stickright and the aircraft willro tat e

clock-wise.If the stick is centered, the aircraft will

always fly in the same direction.

The command stick controls the rotating angular

velocity of the aircraft. Increasing movement of the

Push the stick up and the aircraft willpitchand fly

forward.

Pullthe stickdown and the aircraft willpitchand

flybackward.The aircraft will ke e p le v e l and straight

if the stick is centered.

Increasing movement of the command stick will

le f t.Pushthe stick right and the aircraft willpitch and

flyright.The aircraft will keep level and straight if the

stick is centered.

Increasing movement of the command stick will

position-1 to position-3 and back to position-1

about 6 to 10 times which will force the aircraft to

enter into compass calibration mode.

flipping the S2 switch of the remote controller from

upper most to lower most positions 5 times or more

will reset the current aircraft position as a new

Position-1 Positi on-2 Position-3

Page 5

(2)

For ‘Ready to Fly (non-GPS)’ the aircraft will keep the aircraft level without horizontal

positioning when all sticks are released.

L in k B u tto n & L in k In d ic a t o r

Power off the remote controller, power on the aircraft.You will see the link indicator blinking red.

been successfully established.

Link Indicator

Description

Next Operation

No signal received.

Switch on the remote controller or perform a link procedure.

In link status.

Switch on the remote controller.

5.6 Link between the Remote Controller and Receiver

A5.8G receiver is built-in PHANTOM 2 VISION+, i ts link button and indicator lo c at edo n the bottom of the aircraft as

illustrated in the following diagram.

The link between the remote controller andreceiver isalready established before delivery. Only re-establish the link

when you try to replace the old remote controller or receiver with a new one.

Link Procedures

Press the linkbutton with a thin object and hold until the link indicator blinks yellow.Release the

linkbutton.

Power on the remote controller and the link indicator shouldswitch off. This indicates that the link has

Link Indicator

5.7 Compliance Version Configuration

The compliance version can be reconfigured by twisting the potentiometer knob (See the following diagram) on

the back of the remote controller using a flathead screwdriver. For CE compliance, set the remote controller to CE

compliance by carefullyturning the potentiometer knob to the full counter clock-wise position.For FCC compliance,

set the remote controllerto FCC compliance by carefully turning the potentiometer knob to the full clock-wise

Page 6

position. Users should follow their lo c al regulations accordingly.

FCCCE

When adjusting the potentiometer knob to i ts limit position, be very careful to prevent

Pay attention to and follow local laws and regulations.

The remote controller comes set for CE compliance up delivery as the default setting.

There is another potentiometer reserved.

（1）

damaging the potentiometer knob. Do not apply too much force during this adjustment. Also be

sure to use the correct sized screwdriver.

（2） CE compliant devices have an effective communication range of 300 meters in open spaces due

to power limitations. Be sure to watch your fight distance as the PHANTOM 2 VISION+will

enter Failsafe mode (auto-landing or go home and land) if it fliesbeyond this range.

（3） FCC compliant devices have an effective range of 500 meters in open spaces. Be sure to watch

your fight distance as the PHANTOM 2 VISION+will enter Failsafe mode (auto-landing or go

home and land) if it fliesbeyond this range.

（4）

（1）

（2） It is recommended to use a flathead screwdriver of Φ2.4mm for adjustment.

（3）

Page 7

[1]

[2]

[3 ]

[7 ]

[6 ]

[5 ]

[4 ]

Front View Right View

[1]

[7]

SYSTEM Indicator

Mounting Bracket

SYSTEM Indicator

Description

The Wi-Finetwork is functioning normally.

Off

The Wi-Fi network is functioning abnormally.

POWER Indicator

Description

The range extender is working normally or completely charged.

Low voltage alert, a re-charge is required.

The range extender is charging

6Preparing the Range Extender

The PHANTOM 2 VISION+ range extender is a wireless communication device that operates within the 2.4 GHz

frequency band and is used for extending the effective range of communication between a mobile device

(Smartphone) and the PHANTOM 2 VISION+. In an open unobstructed area, the transmission distance can reach

up to 500 meters, but is usually affected by the surrounding environment, such as trees, buildings and other

sources of the same frequency. Before every flight, it is suggested that you ensure the range extender functions

properly. Otherwise you may experience a communication issue with the mobile device and the PHANTOM 2

VISION+.

Each range extender has a unique MAC address and network name (SSID), details of which are printed on the label

as ‘Phantom_XXXXXX’. The ‘XXXXXX’ represents the last 6 letters or numbers of the MAC address for the range

extender, users can rename the “XXXXXX” part in DJI VISION App.

6.1 The Range Extender

[2]

POWER Indicator

[3]

Lock-screw

[4]

Reset Button

[5]

Power Switch

[6]

Charging Port(Micro-USB port)

SYSTEM Indicator

Tells you the Wi-Fistatus of range extender.

Power Indicator (POWER)

Tells you the power status of range extender.

Page 8

If the power indicator is a solid red light, the ranger extender may stop working at any

moment.Recharge it as soon as possible.

Charging the range extender by connecting the charging port of it to a power supply device (such as PC and

for the first time. It takes 3~4 hours (depending on USB power output) to be fully charged.

Make sure the range extender has enough power battery before each use.

1. Toggle the power switch of range extender to ON position.

3. Keep the range extender facing the aircraft during flight for the best communication link.

It is advised that you power off the range extender after every flight to avoid discharging the battery.

Reset Button

Every time press the reset button once will reset the range extender, and the range extender will restart. Users

have to bind the range extender with a PHANTOM 2 VISON+ again to rebuild a W i-Fi network; otherwise the DJI

VISION App will be failed to connect.

6.2 Usage

Charging the Range Extender

Micro-USB charger) via a Micro-USB cable. Make sure to charge the range extender completely before using it

Powering on the Range Extender

2. Wait for approximately 30 seconds. The Wi-Fi signal indicator should blink green indicatingthe range

extender is communicating properly.

Battery capacity level display

In the main page of DJI VISION App, a progress bar will display the battery capacity level and SSID of current

connecting range extender. The percentage of the progress indicates the percentage of current capacity level. The

progress bar is green when the percentage is no less than 30%, and it’s red when the percentage is less than

30%.When the progress bar turns red, please charge the range extender as soon as possible.

Page 9

1. Tap “Rename SSID of Range Extender” in the Settings page. Enter a new name SSID name (e.g. Phantom_2

,and users will be asked to enter the last six numbers of MAC address on range extender to confirm

Select and connect the renamed network, DJI VISION App can be used.

Low battery capacity warning

During flight, when the range extender is low battery capacity, a warning will appear in the camera page of DJI

VISION App.

6.3Rename SSID of Range Extender

For easier acknowledge the SSID of your range extender, users can rename SSID of range extender.

VISION+) in the textbox.

2. Tap

the modification.

3. Tap“OK” to confirm and the range extendershould automatically restart. Approximately 30 seconds later,

the network named of Phantom_2 VISION PLUS can be searched in theWi-Fi list of your mobile device.

6.4 Binding theCamera &Range Extender

If the connection of PHANTOM 2 VISION+ and range extender is lost, or one of them needs to be repaired or

replaced, a camera and range extender binding will need to be performed via the DJI VISIONApp.

Page 10

Reset

B u tto n

1. Power on the camera and range extender.

procedure is now co mp let ed.

二维码

示例

DO NOT push the reset button of the range extender unless you are ready to rebind the range

extender and the camera! This will unbind your camera and you must follow the steps above to

rebind.

If both the PHANTOM 2 VISION+ aircraft and range extender are powered on and working normally,

you will be able to find the SSID on the Wi-Fi list of the mobile device.

The QR code is located on the packaging of the PHANTOM 2 VISION+. If you cannot find the QR

2. Approximately 30 seconds later, press the resetbutton on the range extender with a thin object until the

SYSTEM Indicator turn off.The range extenderwill then restart automatically.

3. Approximately 30 seconds later, the SYSTEM Indicator should start to blink green, which indicates the

range extender is now ready to be bound.

4. (Fig.1)Run the DJI VISION App->Settings->General->Binding. (Fig.2) Select’Scan the QR Code’ to scan the

camera QR c ode on the product packaging. (Fig.3) Get the camera SSID (E.g. FC200_0xxxxx) and the MAC

address. Users can also skip the scan and enter the camera MAC address directly (Fig.4, Fig.5), the MAC

address can be found on the la be l on camera.

5. Select the tick on the top right corner. The range extendershould automatically restart. The binding

（1）

Page 11

code, please contact DJI customer service to receive the QR code related to your camera’sserial

s suggested to capture the QR code and reserved the picture in your mobile device or PC, in

case of lost the QR code on the package.

number which is printed on the label of camera.

（2） It’

Page 12

Download and install approaches

Scan the QR code to get the download link. Download and install the DJI VISION App

’ as well

ason the packaging of the PHANTOM 2 VISION+.

Approach 2

iOS user

Search “DJI VISION” from App Store, download and install on your mobile device.

An droid user

Search “DJI VISION” from Google Play, download and install on your mobile device.

Supported mobile devices

iOS (iOS6.1 or above)

Recommended: iPhone4s, iPhone5, iPhone5s, iPhone5c, iPod Touch4, iPod

Tou ch5; Available but not recommended:iPad3, iPad4, iPad mini, iPad Air.

An droid (System 4.0 or above)

SamsungGalaxy S3, S4, Note2, Note3 or mobile devices of similar configuration.

DJI continues to support many mobile devices and any information from users are welcome. Please

send any questions or queries to the following mailbox: phantom2vision@dji.com.

Be aware that the DJI website regularly updates so make sure you visit often as well as theApp Store

or Google Play i n o rde r to download the latest version of the DJI VISION App.

Access the Internet to register and login.

[1]

[2]

7Downloading and Installingthe DJI VISION App

7.1 Download and Install

Approach1

7.2 Register & Login

on your mobile device. You can find the QR code on the‘Quick Start Guide

[1] Register

Select ‘Register’ to enter the registratio n page. Fill in your Email and Password information and then ta p

Page 13

to create a new account.

A DJI account is available for all DJI assistant software and app.

You should login to your account the first time you use the DJI VISIONApp.

If you do have an account, but forgot the password, se le ctthe “Forgot password”to retrieve it.

Enable “Tutorial” switch in Settings page, the usage tips will display as the first time you login the App,

[3]

[2] Login

Select ‘Login’ to enter the login page. Fill in your registered Email and Passwordand then ta p to login.

[3] Usage tips

Useful tips will display when you enter the welcome page.Tap the screen to display the next useful tip.

which can help you quickly acquire the usage of DJI VISION App.

Page 14

Page 15

8Connecting the Camera

1. Power on the remote controller and the range extender.

everything is now functioning.

Wi-Fi Connection

Indicator

Enable the Wi-Fi

Select Phantom_XXXXXX

It’s important to using the mobile device connect the Wi-Fi network built by range extender and Wi-Fi module, the

users can use DJI VISION App connect the camera and establish a live camera preview.

8.1 Connecting Procedures

Please carry out the following procedures to connect a mobile device to thecamera of PHANTOM 2 VISION+.

2. Turn on the power of PHANTOM 2 VISION+.

3. (Fig.1)Enable the Wi-Fi on your mobile device; wait for about 30 seconds, and then s ele c t

“Phantom_XXXXXX”from theWi-Fi network list.

4. (Fig.2)Run the DJI VISION App on your mobile device, current Wi-Fi connection status will be indicated

on the main menu. The Wi-Fi connection indicatorturnssolid greenthatmeans the connection is good.

5. Tap the “CAMERA” icon and the DJI VISION Appwill establish a live camera preview (Fig.3). This means

Fig.3

Page 16

Wi-Fi Connection Indicator Description

Icon

Description

Solid green

Wi-Fi is now connected to the PHANTOM 2 VISION+.

Solid blue

Wi-Fi is connected to another Wi-Fi network and NOT to the PHANTOM 2 VISION+.

Off

No Wi-Fi connection.

The SSID is unique for each PHANTOM 2 VISION+which should appear in your Wi-Fi list as

device directly.

（1）

Phantom_XXXXXX.

（2） Android users can tap the SSID button on the main page to enter Wi-Fi settings of the mobile

Page 17

Do not use the aircraft in the severe weather conditions, which include gale force winds (wind speed

Keep your aircraft away from any obstacles, crowds, high voltage power lines, trees or the surface of the

electromagneticinterferences to the remote controller, ensure that your aircraft is not

operating in the complex electromagnetic environment (such as staying close the base station or radio

Do not flight the aircraft in the no-fly zone specified by the local laws or regulations.

(1)

DO NOT calibrate your compass where there is a possibility for the existence of strong magnetic

phones

Flight

After the installation is completed,it’s recommended to take flight trainings refer to PHANTOM PILOT TRAINING

GUIDE to enhance your flight skills or take adequate flight trainingsessions (such as running simulation or

coaching by the experienced user) before you use the aircraft for the first time. Ensure that you have selected a

proper location and environment for your flight.

Flight Environment Requirement

（1）

exceeds category 4), snowy, rainy and smog day.

（2） Chose an open filed as the flight field, where no high building may block the flight route. Also the building

with significant amount of steel structures may affect the accuracy of the compass on the aircraft.

（3）

water at all time when your aircraft is in the air.

（4） To eliminate the

transmitting tower).

（5） The aircraft cannot operate within the polar cycles.

（6）

1 Calibrating the Compass

IMPORTANT: Make sure to perform the Compass Calibration procedures prior to the first flight.The compass is very

sensitive to electromagnetic interferencewhich causes abnormal compass dataand leads topoorflight performance

or even flight failure. Regular calibration of the compass enables the compass to perform at its optimal lev el.

interference such as magnetite, parking structures, and steel reinforcement underground.

(2)

DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular

1.1 Calibration Procedures

Choose an open space to carry out the following procedures. Please watch the quick start video of the PHANTOM 2

VISION+for more details on the compass calibration.

Page 18

N o r m a l L E D

Q u ic k ly flip t h e s w it c h S1

360o R o tate th e airc ra ft

h o r iz o n t a lly

360

R o tate th e airc ra ft

v e rtic a lly (N ose dow nw ard)

P o s itio n -1

S tart h o rizo n ta l ca lib ra tion

S tart v e rtic a l c alib ra tio n

Succeed

F a il

P o s itio n -1

P o s itio n -3->P o s itio n -1

F lip 5 t im e s or above

S tart

c a li

L E D F lig h t In d ic a t o r

P o s itio n -1->P o s itio n -3->P o s itio n -1

F lip once

P o s itio n -3

L E D F lig h t In d ic a t o r

L E D F lig h t

In d ic a to r

Re-calibrate

P o s itio n -1

P o s itio n -3

1.2 Recalibration Scenarios

When CompassData is abnormal,the LED flight indicator will blink alternating between red and yellow.

Severe drifting occurs in flight, i.e. the aircraft does not fly in straight lines.

（1）

（2） Last compass calibration was performed at a completely different flying field/location.

（3） The mechanical str uctu re o f the aircraft has changed, i.e. changed mounting position of the compass.

（4）

Page 19

You SHOULD NOTexecute the CSC during normal flight! This will stop the motors and cause the aircraft

to descend rapidly and drop without any type of control.

1. Place the PHANTOM 2 VISION+ on an o pe n flat ground with battery indicators are facingtowards you.

which will automatically stop the motors.

2 Starting the Motors

A Combination Stick Command (CSC) is used to start the motors instead of simply pushing the throttle stick up.

Push both sticks to their bottom corners as indicated in the diagram below to start the motors. Once the motors

have spun up, release both sticks simultaneously.

There are two methods to stop motors.

Method 1: Conduct CSC again and motors will stop immediately.

Method 2: When the aircraft has descended to the ground, push the throttle stick to its lowest position and hold,

motors will stop 3 seconds later.

3Takeoff/Landing Procedures

2. Power on the remote controller and the range extender, then the intelligent battery.

3. Launch the DJI VISION APP and start the bindingprocess between the mobile device and the PHANTOM 2

VISION+. After the binding is completed, enter the camera preview page.

4. Wait until the LED flight indicator starts to slowly blink green/yellow. This means the aircraft is initializing

and entering the “Ready to Fly”/“Ready to Fly (non-GPS).” s tat e. Then proceed to execute the CSC

command to start motors.

5. Push the throttle stick up slo w l y t o lift the aircraft off the ground. Refer to <Remote Controller Operation

M o de> for more details.

6. Enjoy your flight while capturing and recording with the DJI VISION App. Refer to the<DJI VISION App

Usage> for more details.

7. Be sure you are hovering over a level surface. Pull down on the throttle stick gently to de scend and land.

8. After landing the aircraft on the ground, keep the throttle stick at i ts lowest position for about 3 to 5 seconds

which will automatically stop the motors.

9. After landing the aircraft on the ground, keep the throttle stick at its lowest position for about 3seconds

Page 20

(1)

When the LED flight indicator blinks yellow rapidly during flight, the aircraft has entered into

information:www.dji.com/phantom2visionplus/training.

Home Point:When the aircraft enters into the “Ready to Fly” statusfrom the“Ready to Fly statu s

Home point coordinates will be used to calculate the horizontally distance of the aircraft

the aircraft.

The remote controller is powered off.

remote controller and the aircraft, essentially

There is interferencecausing a signal problem with the remote controller.

The flight control system will try to keep the aircraft level during descent and landing. Note that the aircraft

may be drifting during descent and landing process.

Failsafe mo de , refer to <Failsafe Function>for details.

(2)

A low battery capacity warning is indicated by the LED flight indicator blinking red slowly or

rapidly during flight. Refer to the<Low Battery Capacity Warning Function> for details.

(3)

Watch the quick start video about flight for more flight

4 Failsafe Function

The aircraft will enter Failsafe m o dewhen the connection from the remote controller is lost. The flight control

system will automatically control the aircraft toreturn to home and lan d to redu ce injuries or damage.

(non-GPS)”, the aircraft will record the current GPS coordinates as the home point.

1) When remote controller signal is lost, PHANTOM 2 VISION will use the recorded the home

point coordinates as the home point for landing.

(shown as “D” on the GUI of the DJI VISION app).

3) After successfully record the home point, you can see a fast blink of LED flight indicators on

4.1 Possible Failsafe Scenario

（1）

（2） The aircraft has flown out of the effective communication range of the remote controller.

（3） There is an obstacle obstructing the signal between the

reducing thedistance the signal can travel.

（4）

4.2Fails af e Procedure

Initiating the Failsafe mode from different flying statuses will results in the different landing process. There are two

types flying status that may affect the Failsafe landing process, one is “Ready to Fly” status and the other is “Ready

to Fly (non-GPS)” status. The differences between these two statuses are shown as below:

Ready to Fly(non-GPS) ----Automatic landing

Ready to Fly ----Automatic go home and land

SZ DJI TECHNOLOGY RE7001402 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual