SZ DJI TECHNOLOGY M200V21811 User Manual

Download

Page 1

MATRICE 200 SERIES

M210/M210 RTK

Quick Start Guide V1.0

Page 2

19 20 21

18 22

Matrice 210 V2 / Matrice 210 RTK V2

The DJI class agility and speed, redundant barometers and IMUs for maximum reliability, and smart flight features that make capturing complex shots easy. The aircraft’s visual sensors* enable enhanced hovering precision even when flying indoors or in environments where GNSS is unavailable. The built-in AirSense makes you aware of your surrounding airspace to ensure flight safety. Its airframe design gives it an IP43 Ingress Protection Rating, in accordance with the global IEC 60529 standard. The mechanical design, along with quick-release landing gears and mounted folding arms, makes it easy to transport, store, and prepare for flight. The safety beacons on both the top and the bottom of the aircraft allow the aircraft to be identified at night or in low light conditions.

The M210 V2/M210 RTK V2 is compatible with many of DJI’s DGC2.0 connector gimbals, supporting a single upward g imbal or dual downward gimbals.* It is equipped with many expansion ports to broaden its applications. The M210 RTK V2 has a built- in DJI D-RTKTM, which provides more accurate heading data for positioning.** An advanced power management system along with dual batteries ensures power supply and enhances flight safety. Without a payload, the M210 V2 has a flight time of up to 38 minutes with standard batteries (TB55), while the M210 RTK V2 has up to 32 minutes of flight time.*

This manual uses the M210 RTK V2 and ZENMUSE

MATRICE

210 V2/Matrice 210 RTK V2 (M210 V2/M210 RTK V2) is a powerful industrial-grade flight platform with world-

Z30 and X5S gimbals as an example to demonstrate setup.

* The Vision and Infrared Sensing Systems are affected by surrounding conditions. Read the Disclaimer and Safety Guidelines to learn more.

Gimbals can be purchased separately from the official DJI website. When using a single upward gimbal with the M210 V2, an external GPS module connected through the expansion port is required. Please refer to the user manual for more details about expansion ports, upward gimbals, and downward gimbals. Please note that maximum flight times are measured in ideal flight conditions. Actual flight times may vary depending on your environment. DO NOT disassemble the aircraft shell, otherwise it will not be covered under warranty.

**Please note that this list of items applies to the M210 RTK V2. Although similar, the M210 V2 aircraft does not include the D-RTK antennas and mounting bracket.

When using the M210 RTK V2, more accurate positioning data can be achieved when using a Network RTK service or a DJI D-RTK 2 High-Precision GNSS Mobile Station for Matrice (purchased separately). If the data transmission signal between the aircraft and the Network RTK server or mobile station is weak, it is recommended to use post-processed kinematic (PPK) technology.

Folded

1. FPV Camera

2. Forward Vision System

3. DJI Gimbal Connector v2.0 (DGC2.0) I

4. DJI Gimbal Connector v2.0 (DGC2.0) II

5. Gimbal Detachment Button

6. Frame Arms

7. Motors

8. Propellers

9. ESC LEDs

10. Transmission Antennas

11. Landing Gears

12. Upward Gimbal Mounting Position

Night flight indicator

13.

14. Upward Infrared Sensor

15. Aircraft Status Indicators

16. D-RTK Mounting Bracket**

17. D-RTK Antennas**

18. Extended Power Port (XT30)

19. USB Mode Switch

20. USB Port

21. Linking Button and Indicator

22. Expansion Ports

23. Battery Removal Button

24. Intelligent Flight Batteries

25. Battery Level Indicators

26. Power Button

27. Downward Vision System

28. microSD Card Slot

Page 3

Cendence S Remote Controller

2 3 6

17 18

39 40 41

35 45

The Cendence mi (7 km).* Equipped with a DJI CrystalSky app, providing a precise and responsive flying experience. Dual frequency* support makes the HD video downlink more stable. In Dual Remote Controller Mode, two remote controllers control the aircraft and camera separately, even when they are up to 656 feet (200 m) apart.

The remote controller works with a WB37 Intelligent Battery, which can be fully charged via the charging port in about 2 hours and 24 minutes with the standard charger, or with the Intelligent Battery Charging Hub in about 1 hour and 11 minutes. The maximum run time of the remote controller is approximately 4 hours without supplying power to a monitor and with Dual Remote Controller mode disabled.*

S remote controller features DJI’s OCUSYNC

7.85 inch ultra-bright monitor, it displays a live HD view directly via the built-in DJI Pilot

33. Left Lever

34. Left Dial (Gimbal Pitch)

35. Flight Mode Switch

36. Handle Bar

37. USB Port (for Mobile Device Connection)

38. HDMI A Port (for Video Output)

39. CAN Bus Port (Extension Port)

40. Micro USB Port

41. SDI Port (for Video Output)

42. Right Lever

43. Right Dial (Gimbal Pan)

44. AF Button (Autofocus)

45. Record Button

46. Shutter Button

47. Customizable Buttons (C1-C4)

* The remote controller can reach its maximum transmission distance (FCC) in an unobstructed area with no electro-magnetic interference at an altitude of about

400 feet (120 meters). The actual maximum transmission distance may be less than the distance mentioned above due to interference in the operating environment, and the actual value will fluctuate according to the strength of interference. To comply with local regulations, the 5.8 GHz frequency is not available in some countries and regions. For more information about Dual Remote Controller mode, please refer to the user manual. Maximum run time is estimated in a lab environment without supplying power to a smart device or monitor, for reference only.

2.0 technology for a maximum transmission distance of up to 4.3

1. HDMI Port

2. USB Port

3. Micro SD Card Slot

4. Micro USB Port

5. Headphone Jack

6. Light-Sensitive Port

7. Power Button

8. Customizable Button (F1)

9. Setting Button

10. Customizable Button (F2)

11. Back Button

12. Battery Release Button

13. WB37 Intelligent Battery

14. Antennas

15. Monitor Mounting Bracket

16. USB Port (Reserved Port)

17. Control Sticks

18. Strap Hook

19. Focal Adjustment Knob

20. Return-to-Home (RTH) Button

21. Power Port

22. EV Setting Button

23. Shutter Setting Button

24. Aperture Setting Button

25. ISO Setting Button

26. Pause Button

27. Power Button

28. Remote Control Display

29. Camera Settings Dial

30. Customizable Button Setting Menu

31. Customizable Buttons (BA-BH)

32. Support Rig

Page 4

Using Matrice 210/Matrice 210 RTK

1. Downloading the DJI Pilot App

Users can access the DJI Pilot app that is built-in to the remote controller’s CrystalSky monitor. Users can also search for DJI Pilot in Google Play Store or scan the QR code below to download the app onto your mobile device, and then connect the mobile device to the remote controller.

First-time activation requires your DJI account and an internet connection.

Internet

DJI Pilot supports Android 4.4 or later.

2. Charging the Batteries

Press the release button and open the corresponding charging port cover. Insert the Intelligent Flight Battery into the charging port to begin charging. Be sure to press the release button when removing fully charged batteries.

Using the IN2CH Charging Hub, charging time is approximately. TB55: 2 hours and 33 min (two batteries)*

When charging is complete, the LED lights on the Intelligent Flight Battery will turn off, and the LED on the Charging Hub will turn solid green. When charging is complete, the display on the remote controller will show 100%. The Charging Hub will sound an alert when the battery has been fully charged. The alert can be turned on or off by toggling the switch under the hub. Connect the Intelligent Flight Batteries to the aircraft and power them on. If battery temperature is lower than 15° C, the system will auto heat the batteries to maintain a temperature between 15° and 20° C. Ensure two Intelligent Flight Batteries are charged and discharged simultaneously to prolong their service life and for a better flight experience.

Charging Time: 2 hours and 24 min*

Using the WCH2 Charging Hub, charging time is approximately 1 hour and 11 min (one battery)*

3. Preparing the Remote Controller

Mounting Monitor and Remote Controller Batteries

CrystalSky monitors and the Cendence S remote controller use the same batteries.

Put the battery into the Battery Slot, then slide it to the end until you hear a click.

Press the Battery Release Button before removing the battery. Press the Battery Level Button once to check the battery level.

Mounting the Monitor to the Remote Controller

Ensure that Part B is unlocked. Connect Part B to Part A.

Lock the Mounting Bracket.

Use a coin or the screwdriver included to adjust the tightness of the tilt axis.

DJI Pilot App

Power Outlet 100~240 V (50Hz/60Hz)

*Provided charger

Low

High

Page 5

Left Right

2 1

Using the Remote Controller

The Stick Mode is set to Mode 2 by default. In Mode 2, the left stick controls the aircraft’s elevation and heading, and the right stick controls the aircraft’s forward, backward, and lateral movements. To adjust the FPV camera, press and hold the C2

Button and rotate the left dial.

Left Stick Right Stick FPV Camera

Forward

Turn Left

For more information about how to connect and use the remote controller, please refer to the user manual. You can change the stick mode and customize the C1-C4 and BA-BH buttons’ functi ons in the DJI Pilot app.

Down

Turn Right

Backward

4. Preparing the Aircraft

Unfolding the D-RTK Antennas (for M210 RTK V2 only)

Unfold the D-RTK antennas and then turn the knob tightly in the direction indicated by the lock icon .

For the aircraft to take off, the D-RTK antennas must be fully unfolded and securely locked.

Installing the Landing Gears Unfolding the Aircraft

Unfold the frame arm, slide the arm lock to the end of the frame arm, then rotate it about 90° until the silver line lies within the range of the icon.

Page 6

1 2 3

Mounting the Propellers

Mounting the Gimbal and Camera

Propellers without silver rings should be installed on unmarked motors.

Press the propeller down onto the mounting plate and rotate it in the direction indicated by the lock icon until secure.

Propellers with silver rings should be installed on motors with the same color marks.

Check that the propellers are secure before each flight.

Press the Gimbal Detachment button to remove the cover.

Make sure to press down the gimbal detachment button when rotating the gimbal lock to remove the gimbal and camera. The gimba l lock should be fully rotated when removing the gimbal for the next installation.

Mounting the Intelligent Flight Batteries

Insert a pair of batteries. Press once to check the battery level. Press again and hold until the batteries turn on or off.

Only use battery slot B when using one battery to supply power. In this case, the aircraft can only be powered on, but cannot take off. If for any reason only one battery is available during flight, land the aircraft immediately and replace the batteries as soon as possible. Make sure to press the Battery Removal button when removing the battery. Make sure to use the included TB55 batteries. TB50 batteries are not recommended as they may reduce the flight performance.

Configuring the RTK Module (for M210 RTK V2 only)

The M210 RTK V2 aircraft includes D-RTK antennas. Highly accurate positioning data can be obtained when using the M210 RTK V2 with the DJI D-RTK 2 High-Precision GNSS Mobile Station for Matrice or Network RTK service.

1. In the Camera View in the DJI Pilot app, tap on the upper right corner, and then tap RTK. Enable aircraft RTK and select a service type in settings.

2. If D-RTK 2 is selected, refer to the D-RTK 2 Mobile Station for Matrice user guide for information on configuration. Contact a DJI authorized dealer for details on the use of Network RTK.

Align the white and red dots and insert the gimbal.

Rotate the gimbal lock to the locked position.

Gimbal Connector II Gimbal Connector I

Zenmuse XT ZenmuseX4S/X5S/X7/XT2/Z30

Zenmuse Z30 Zenmuse X4S/X5S/X7/XT/XT2

High

Low

Page 7

Ready to Go (GPS)

DJI Pilot

App

5. Flight

Toggle the Flight Mode switch to

P-mode, the safest flight mode.

Power on the remote controller, monitor, and aircraft. Pilot app.

After the monitor is powered on, wait for a pop-up window that asks for a s election of USB device use, and then select “DJI Pilot”. Otherwise, the app c annot be connected to the remote controller. Always set an appropriate RTH altitude before takeoff. Please refer to the Disclaimer and Safety Guidelines for more details.

Manual Takeoff

Combination Stick Command to start/stop the motors Left stick up

Return-to-Home

Rotating propellers can be dangerous. DO NOT start the motors in narrow

spaces or when there are people nearby. Always keep your hands on the remote controller so long as the motor is still spinning. After landing, power off the aircraft before turning off the remote controller.

Press and hold to initiate the RTH procedure. Press again to cancel.

It is important to understand basic flight guidelines for the safety of both you and those around you. Refer to the Disclaimer and Safety Guidelines for more information.

Launch the DJI

(slowly) to take off

Before taking off, ensure that the Aircraft Status Bar in the

DJI Pilot app reads ‘Ready to Go (GPS)’ or ‘Ready t o Go (Vision)’ if flying indoors.

Manual Landing

Pull left stick down (slowly) until you touch the ground. Hold for a few seconds to stop the motors.

To stop the motors mid-flight, press

the RTH button while simultaneously pulling the left stick to the bottom inner corner. Stop motors midflight will cause the aircraft to crash. The motor can only be stopped mid-flight when the flight controller detects critical error.

GEO Zones

Learn more: http://flysafe.dji.com/no-fly

Page 8

Specifications

Aircraft (M210 V2 / M210 RTK V2)

Dimensions M210 V2: Unfolded, propellers and landing gears included, 883×886×398 mm

Diagonal Wheelbase 643 mm Max Takeoff Weight 6.14 kg Operating Frequency 2.4000-2.4835 GHz; 5.725-5.850 GHz

Hovering Accuracy (P-mode with GPS) Vertical: ±1.64 feet (0.5 m) or ±0.33 feet (0.1 m, Downward Vision System enabled) Hovering Accuracy (D-RTK) Vertical: ±0.33 feet (0.1 m); Horizontal: ±0.33 feet (0.1 m)

Max Angular Velocity Pitch: 300°/s, Yaw: 150°/s Max Pitch Angle (Dual Downward Gimbal/Single Upward Gimbal) S-mode: 30°, P-mode A-mode: 25° Max Pitch Angle (Single Downward Gimbal) S-mode: 35°; P-mode: 30° (Forward Vision System enabled: 25°); A-mode: 30° Max Ascent Speed 16.4 ft/s (5 m/s) Max Descent Speed (vertical) 9.8 ft/s (3 m/s) Max Speed (Dual Downward Gimbal/Single Upward Gimbal) S-mode: 75.6 kph (47 mph); P-mode/A-mode: 61.2 kph (38 mph) Max Speed (Single Downward Gimbal) S-mode/A-mode: 82.8 kph (51.4 mph); P-mode: 61.2 kph (38 mph) Max Service Ceiling Above Sea Level 9842 feet (3000 m, with 1760S propellers) Max Wind Resistance 39.4 ft/s (12 m/s) Max Flight Time (with TB55 batteries) M210 V2: 38 min (no payload), 24 min (takeoff weight: 6.14 kg)

Supported DJI Gimbals Zenmuse X4S/X5S/X7/XT/XT2/Z30 Supported Gimbal Configurations Single Downward Gimbal, Dual Downward Gimbals, Single Upward Gimbal Ingress Protection Rating IP43 GNSS M210 V2: GPS+GLONASS; M210 RTK V2: GPS+GLONASS+BeiDou+Galileo Operating Temperature -4° to 122° F (-20° to 50° C) Operating Frequency 2.4000-2.4835 GHz; 5.725-5.850 GHz

Remote Controller (GL900A)

Max Transmitting Distance (unobstructed, free of interference)

Power Supply Extended Intelligent Battery (Model: WB37-4920mAh-7.6V) Output Power 13 W (Without supplying power to monitor) USB Power Supply iOS: 1 A 5.2 V (max); Android: 1.5A 5.2 V (max) CrystalSky Monitor DJI CrystalSky 7.85inch, Resolution: 2048×1536;

Operating Temperature -4° to 122° F (-20° to 50° C)

Downward Vision System

Velocity Range <32.8 ft/s (10 m/s) at the height of 6.56 feet (2 m) Altitude Range <32.8 feet (10 m) Operating Range <32.8 feet (10 m) Operating Environment Surfaces with clear patterns and adequate lighting (>15 lux) Ultrasonic Sensor Operating Range 0.33-16.4 feet (0.1-5 m) Ultrasonic Sensor Operating Environment Non-absorbing material, rigid surfaces (thick indoor carpeting will adversely affect performance)

Forward Vision System

Obstacle Sensing Range 2.3-98.4 feet (0.7-30 m) FOV Horizontal: 60°; Vertical: 54° Operating Environment Surfaces with clear patterns and adequate lighting (> 15 lux)

Upward Infrared Sensing System

Obstacle Sensing Range 0-16.4 feet (0-5 m) FOV ±5° Operating Environment Large, diffuse, and reflective obstacles (reflectivity >10%)

Intelligent Flight Battery (TB55-7660mAh-22.8V)

Capacity 7660 mAh Voltage 22.8 V Battery Type LiPo 6S Energy 174.6 Wh Net Weight (Single One) Approx. 885 g Operating Temperature -4° to 122° F (-20° to 50° C) Charging Temperature 41° to 104° F (5° to 40° C) Max Charging Power 180 W

Charger (Model: IN2C180)

Voltage 26.1 V Rated Power 180 W

Charging Hub (Model: IN2CH)

Input Voltage 26.1 V Input Current 6.9 A

Download the latest version from

http://www.dji.com/matrice-200-series-v2

※ This content is subject to change without prior notice.

Folded, propellers and landing gears excluded, 722×282×242 mm M210 RTK V2: Unfolded, propellers and landing gears included, 883×886×427 mm Folded, propellers and landing gears excluded, 722×282×242 mm

Horizontal: ±4.92 feet (1.5 m) or ±0.98 feet (0.3 m, Downward Vision System enabled)

M210 RTK V2: 32 min (no payload), 24 min (takeoff weight: 6.14 kg)

FCC: 5 mi (8 km); CE/MIC: 3.1 mi (5 km); SRRC: 3.1 mi (5 km)

Brightness: 2000 cd/m2; Operating System: Android 5.1; Storage: ROM 64GB

DJI incorporates HDMI The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

technology.

MATRICE and DJI are trademarks of DJI.

Printed in China.

Page 9

FCC/ISEDC ComplianceNotice

This device complies with Part 15 of the FCC Rules and ISEDC licence-exempt RSS standard (s). Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operatio n. Any Changes expressly or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment.

Cet appareil est conforme à la section 15 des règles de la FCC et aux normes RSS exemptes de licence ISEDC. Son fonctionnement est soumis aux deux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles et (2) cet appareil doit accepter toutes les interférences reçues, y compris celles pouvant entraîner un fonctionnement non souhaité. Toute modification expresse ou non approuvée par la partie responsable de la conformité peut annuler l'autorité de l'utilisateur à utiliser l'équipement.

Note: This equipment has been tested and found to comply with the li mits for a Class B digi tal device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications . Howev er, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determ ined by turni ng th e e quipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information

Aircraft complies with FCC/ ISEDC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC/ ISEDC radio frequency exposure limits, human

Page 10

proximity to the antenna shall not be less than 20cm during normal operation. For Remote Controller (model GL900A),SAR tests are conducted using standard operating positions accepted by the FCC/ ISEDC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model is a available for sale to the public, it must be tested and certified to the FCC/ ISEDC that it does not exceed the exposure limit established by the FCC/ ISEDC, Tests for each product are performed in positions and locations as required by the FCC/ ISEDC. For Handheld operation, this device has been tested and meets the FCC/ ISEDC RF exposure guidelines when used with an accessory designated for this product or when used with an acces sory that contains no metal. For body worn operation, Remote Controller (model GL900A) has been tested and meets the FCC/ ISEDC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that Contains no metal and that positions the handset a minimum of 10 mm from the body. Non-compliance with the above restrictions may result in violation of RF exposure guidelines.

ISEDC Radiation Exposure Statement: L’aéronef est conforme aux limites d’exposition aux rayonnements de la FCC/ ISEDC établies pour un environnement non contrôlé. Afin d'éviter tout risque de dépassement des limites d'exposition aux fréquences radioélectriques imposées par la FCC/ ISEDC, la proximité humaine de l'antenne ne doit pas être inférieure à 20 cm en fonctionnement normal. Pour le contrôleur à distance (modèle GL900A), les tests SAR sont effectués à l'aide de positions de fonctionnement standard acceptées par la FCC/ ISEDC, l'appareil transmettant à son niveau de puissance certifié le plus élevé dans toutes les bandes de fréquences testées, bien que le SAR soit déterminé au niveau de puissance certifié Le niveau de DAS de l'appareil en cours d'utilisation peut être bien inférieur à la valeur maximale. Avant qu'un nouveau modèle ne soit disponible à la vente au public, il doit être testé et certifié par la FCC/ ISEDC qu'il ne dépasse pas la limite d'exposition fixée par la ISEDC. Les tests de chaque produit sont effectués à des emplacements et à des emplacements requis par la ISEDC. . Pour le fonctionnement en mode portable, cet appareil a été testé et respecte les directives d'exposition RF de la FCC/ ISEDC lorsqu'il est utilisé avec un accessoire conçu pour ce produit ou avec un accessoire ne contenant pas de métal. Pour une utilisation sur le corps, la télécommande (modèle GL900A) a été testée et répond aux

Page 11

directives d'exposition RF de la FCC/ ISEDC lorsqu'elle est utilisée avec un accessoire conçu pour ce produit ou avec un accessoire ne contenant pas de métal et positionnant le combiné à 10 mm minimum. du corps. Le non-respect des restrictions ci-dessus peut entraîner une violation des consignes d'exposition aux RF.

KCC W arning Message “해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다.” “해당 무선설비는 운용 중 전파혼신 가능성이 있음” NCC W arni ng Message

低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應

改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Page 12

Hay disponible online una copia de la Declaración de conformidad UE en www.dji.com/eurocompliance

Dirección de contacto de la UE: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

EU-verklaring van overeenstemming: SZ DJI TECHNOLOGY CO., LTD. verklaart hierbij dat dit apparaat voldoet aan de essentiële vereisten en andere relevante bepalingen van Richtlijn 2014/53/EU. De EU-verklaring van overeenstemming is online beschikbaar op www.dji.com/euro-compliance

Contactadres EU: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

Declaração de conformidade da UE: A SZ DJI TECHNOLOGY CO., LTD. declara, através deste documento, que este dispositivo está em conformidade com os requisitos essenciais e outras disposições relevantes da Diretiva 2014/53/EU. Existe uma cópia da Declaração de conformidade da UE disponível online em www.dji.com/eurocompliance

Endereço de contacto na UE: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

Dichiarazione di conformità UE: SZ DJI TECHNOLOGY CO., LTD. dichiara che il presente dispositivo è conforme ai requisiti essenziali e alle altre disposizioni rilevanti della direttiva 2014/53/EU. Una copia della dichiarazione di conformità UE è disponibile online all'indirizzo Web www.dji.com/euro-compliance

Indirizzo di contatto UE: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

Déclaration de conformité UE : Par la présente, SZ DJI TECHNOLOGY CO., LTD déclare que cet appareil est conforme aux principales exigences et autres clauses pertinentes de la directive européenne 2014/53/EU. Une copie de la déclaration de conformité UE est disponible sur le site www.dji.com/euro-compliance

Adresse de contact pour l'UE : DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

EU-Compliance: Hiermit erklärt SZ DJI TECHNOLOGY CO., LTD., dass dieses Gerät den wesentlichen Anforderungen und anderen einschlägigen Bestimmungen der EU-Richtlinie 2014/53/EU entspricht. Eine Kopie der EU-Konformitätserklärung finden Sie online auf www.dji.com/euro-compliance.

Kontaktadresse innerhalb der EU: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

Page 13

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but

have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

Umweltfreundliche Entsorgung

Elektro-Altgeräte dürfen nicht mit gewöhnlichem Abfall entsorgt werden und müssen

separat entsorgt werden. Die Entsorgung an kommunalen Sammelstellen ist für Privatpersonen kostenlos. Die Eigentümer der Altgeräte sind für den Transport zu den Sammelstellen verantwortlich. Durch diesen geringen Aufwand können Sie zur Wiederverwertung von wertvollen Rohmaterialien beitragen und dafür sorgen, dass umweltschädliche und giftige Substanzen ordnungsgemäß unschädlich gemacht werden.

Tratamiento de residuos responsable con el medio ambiente

Los aparatos eléctricos viejos no pueden desecharse junto con los residuos orgánicos, sino

que deben ser desechados por separado. Existen puntos limpios donde los ciudadanos pueden dejar estos aparatos gratis. El propietario de los aparatos viejos es responsable de llevarlos a estos puntos limpios o similares puntos de recogida. Con este pequeño esfuerzo estás contribuyendo a reciclar valiosas materias primas y al tratamiento de residuos tóxicos.

Mise au rebut écologique

Les appareils électriques usagés ne doivent pas être éliminés avec les déchets résiduels. Ils

doivent être éliminés séparément. La mise au rebut au point de collecte municipal par l'intermédiaire de particuliers est gratuite. Il incombe au propriétaire des appareils usagés de les apporter à ces points de collecte ou à des points de collecte similaires. Avec ce petit effort personnel, vous contribuez au recyclage de matières premières précieuses et au traitement des substances toxiques.

Smaltimento ecologico

I vecchi dispositivi elettrici non devono essere smaltiti insieme ai rifiuti residui, ma devono

essere smaltiti separatamente. Lo smaltimento da parte di soggetti privati presso i punti di raccolta pubblici è gratis. È responsabilità del proprietario dei vecchi dispositivi portarli presso tali punti di raccolta o punti di raccolta analoghi. Grazie a questo piccolo impegno personale contribuirete al riciclo di materie prime preziose e al corretto trattamento di sostanze tossiche.

Page 14

Milieuvriendelijk afvoeren

Oude elektrische apparaten mogen niet worden weggegooid samen met het restafval,

maar moeten afzonderlijk worden afgevoerd. Afvoeren via het gemeentelijke inzamelpunt is gratis voor particulieren. De eigenaar van oude toestellen is verantwoordelijk voor het inleveren van de apparaten op deze of vergelijkbare inzamelpunten. Met deze kleine persoonlijke inspanning lever je een bijdrage aan de recycling van waardevolle grondstoffen en de verwerking van giftige stoffen.

Eliminação ecológica

Os aparelhos elétricos antigos não podem ser eliminados juntamente com os materiais residuais. Têm de ser eliminados separadamente. A eliminação no ponto de recolha público através de entidades particulares é gratuita. É da responsabilidade do proprietário de aparelhos antigos levá-los a estes pontos de recolha ou a pontos de recolha semelhantes. Com este pequeno esforço pessoal, contribui para a reciclagem de matérias-primas úteis e para o tratamento de substâncias tóxicas.

SZ DJI TECHNOLOGY M200V21811 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual