SZ DJI TECHNOLOGY 800TC1512, 800RX1512 Users manual

Thumb Contr

User Manual

V1.0 2015.4

oller

Disclaimers and W

Congratulations on purchasing your new DJI product. Carefully read
the manual and all disclaimers before using this product. By using
this product, you hereby agree to this disclaimer and signify that you
have read it in its entirety. You agree that you are responsible for your
own conduct, for all content that is created using this product, and for
any consequences that may arise from either. You agree to use this
product only for purposes that are proper and in accordance with local
regulations, stated terms, and all applicable polices and guidelines.

By reading this disclaimer, you also agree that:

1. Any part of this disclaimer is subject to change without prior
notice. Refer to www.dij.com for the latest version.

DJI

2. 

 reserves the right of nal interpretation of this disclaimer.

As DJI has no control over  use, setup, nal assembly, modication, 

or misuse of its products, no liability shall be assumed or accepted
for any resulting damage or injury. By using, setting up, or
assembling the product, the user accepts all resulting liability. DJI
assumes no liability for damages or injuries incurred directly or
indirectly from the use of this product.

DJI is a registered trademark. All names of products, brands, etc.
appearing in this manual are trademarks or registered trademarks
of their respective owner companies. This product and manual are
copyrighted by DJI, with all rights reserved. No part of this product
or manual shall be reproduced in any form without the prior written
consent or authorization of DJI. No patent liability is assumed with
respect to the use of the product or information contained herein.

2015 DJI. All Rights Reserved.

©

2

arnings

Content

Disclaimers and W
In the Box 4
Introduction 5

Thumb Controller 5
External Receiver (For Ronin Only) 6

Installation 7

Installing the Thumb Controller 7
I

nsta lling the External Receiver (For Ronin Only)

Connecting the

C

onnecting the Thumb Controller to the Ronin-M
Connecting the Thumb Controller to the Ronin 9
Indicator Status 11

Using the

Mode 12
Function 13
Gimbal Settings 13
Device Settings 14

DJI Assistant App

PC/MAC Assistant Tuning

DJI

Settings 17
Updating the Thumb Controller and the Receiver 18

Specications 20

arnings

2

Thumb Controller to the Gimbal

Thumb Controller

12

16

Tuning

17

2015 DJI. All Rights Reserved.

©

8

9

9

3

In the Box

Ch

eck to ensure that all of the following items are included in the

package. If any items are missing, contact DJI or your local dealer.

The following items are included with the Thumb Controller for the
Ronin-M:

Thumb Controller×1 Quick Release Accessory

Mount×1

USB Cable×1 Rubber

Ring×1

The following items are included with the Thumb Controller for the Ronin:

Thumb Controller×1 Quick Release Accessory

Receiver×1 Adhesive Tape×14-Pin Cable×1

2015 DJI. All Rights Reserved.

©

4

Mount ×1

USB Cable×1

Introduction

The Thumb  Controller is  designed  specically for  DJI Ronin  series 

handheld gimbals. It provides a simple, intuitive interface for
controlling the gimbal’s pan, tilt, and roll motion. The pressure­sensitive stick and the easy-to-read OLED display give Ronin users
more control than ever before.
The Thumb Controller communicates with the Ronin-M via a
preinstalled internal receiver. An external receiver is needed when
the Thumb Controller is used with the Ronin.

Thumb Controller

[1]

[3]

[4]

[1] Power Button

[2]

[2] Status Indicator

[3] OLED Display

[4] Pressure-Sensitive Stick

©

Press and hold the power
button to turn on/off the Thumb
Controller

I

ndicates the status of the

Thumb Controller

Displays the menu of the
Thumb Controller

ransmits the user’s input to

T
the force sensor

2015 DJI. All Rights Reserved.

5

[5] Micro-USB Port

[5]

[6] Override Button

[6]

External Receiver (For Ronin Only)

[1] CAN Port

[1]

[2] Bind Button

[3]

[2]

[3] LED Indicator

[4]

2015 DJI. All Rights Reserved.

©

6

[4] Micro-USB Port

For charging the Thumb
Controller and upgrading its

rmware

Allow the Thumb Controller
to reactivated and updated
following a failure update
process

Connects the receiver to the
Ronin

Connects the Thumb
Controller to the Ronin

Indicates the status of the
receiver

For upgrading the rmware

Installation

Installing the

1. Install the quick-release accessory mount by clamping it around
the handlebar of the Ronin and tightening the screw. Remember
to place the rubber ring on the on the handlebar and clamp the
accessory mount around it when installing the unit on the Ronin-M.

2. Insert the Thumb Controller into the quick-release accessory
mount and ensure that it is secure.

Thumb Controller

2015 DJI. All Rights Reserved.

©

7

Installing the External Receiver (For Ronin Only)

1. Use the 4-pin cable to connect the CAN port on the Ronin to the
CAN 1 or Can 2 port on the receiver.

2. Use the adhesive tape to secure the receiver on the Ronin.

2015 DJI. All Rights Reserved.

©

8

Connecting the Thumb Controller to the Gimbal

Connecting the

1. Turn on the Ronin-M.

2. Press the
LED indicator on the Ronin-M will rapidly blink green.

3. Turn on the Thumb Controller. If the LED indicator on the Ronin-M
and the LED indicator on the Thumb Controller both glow solid
green, they have been successfully connected.

Thumb Controller to the Ronin-M

Ronin-M’s Bind Button (shown below) one time. The

Bind Button

Connecting the

1. Turn on the Ronin.

2. Press the Bind Button on the receiver one time. The LED indicator
on the receiver will rapidly blink green.

3. Turn on the Thumb Controller. If the LED indicator on the receiver
and the LED indicator on the Thumb Controller both glow solid
green, they have been successfully connected.

Thumb Controller to the Ronin

2015 DJI. All Rights Reserved.

©

9

Bind Button

The

binding process only needs to be completed one time,
unless the bind button is pressed or the Ronin/Ronin-M
needs to be connected to another Thumb Controller.

2015 DJI. All Rights Reserved.

©

10

Indicator Status

Thumb Controller
LED Indicator Status

Solid Red

—

Blinking Red

Solid Green

—

Blinking Green

Solid Yellow The Thumb Controller is fully charged

—

Description

The Thumb Controller is being
updated

The Thumb Controller is not connected
to the receiver

The Thumb Controller is connected to
the receiver

The update process is complete

External Receiver LED
Indicator Status

Solid Red The receiver is being updated

—

Blinking Red

Solid Green

—

Blinking Green The update process is complete

Blinking Green Quickly Binding

Description

The Thumb Controller is not
connected to the receiver

The Thumb Controller is
connected to the receiver

2015 DJI. All Rights Reserved.

©

11

Using the Thumb Controller

To enter the Main Menu, press and hold the center of the pressure­sensitive stick.

Mode

Function

Gimbal Setting

Menu

Device Setting

Default Setting

About

2015 DJI. All Rights Reserved.

©

12

ST Off
ST On

Auto Center

Fast
Normal
Slow

Channel

Direction

Calibration

Sensitivity

Sleep

Power off

Restore

Version

Up/Down

Left/Right

Up/Down

Left/Right

Cali System
Auto Tune

Soft
Hard

1min
5min
10min
Never

10min
30min
60min
Never

**

Pan
Roll
Tilt
None

Pan
Roll
Tilt
None

Normal
Reverse

Normal
Reverse

The

Main Menu contains six tabs: Mode, Function, Gimbal Setting,
Device Setting, Default Setting, and About.
Press up/down on the pressure-sensitive stick to select an item. Press
right to view and select options and press left to return to the Main Menu.

RF NC

Ronin

DJI
Thumb Controller
Menu

Mode

Off

ST

SmoothTrack is off. The Thumb Controller is free to control the pan
axis. The gimbal will stop and hold the last position determined by
the pan axis control stick, without applying SmoothTrack.

ST On

SmoothTrack is on. The Thumb Controller is free to control the pan
axis. The gimbal will stop and hold the last position determined by
the pan axis control stick, while applying SmoothTrack.

Auto Center

SmoothTrack is on. The gimbal will apply SmoothTrack when
reorienting and resetting the pan angle to the forward-facing
direction after the pan axis control stick is released.

2015 DJI. All Rights Reserved.

©

13

Function

The Function tab allows you to select the SmoothTrack speed.
There are 3
of each speed can be adjusted in the DJI Assistant app or the PC/
MAC Assistant.

possible speeds: Fast, Normal, and Slow. The value

Gimbal Settings

Channel

Al

lows you to assign control of the pan, tilt, or roll motion of the
gimbal to the up/down input on the pressure-sensitive stick.
Allows you to assign control of the pan, tilt, or roll motion of the
gimbal to the left/right input on the pressure-sensitive stick.
Selecting ‘None’ means that the corresponding input axis from the
pressure-sensitive stick will not affect the movement of the gimbal.

By default, the up/down input on the pressure-sensitive

stick controls the tilt axis movement of the gimbal and the
left/right input on the pressure-sensitive stick controls the
pan axis movement of the gimbal.

If you reassign the control input of either axis, only the most

recent assignment will be valid.

Direction

By default, the “Normal” direction orientation scheme indicates
that the up movement of the stick moves the tilt axis up and the
down movement of the stick moves the tilt axis down, while the left
movement of the stick rotates the pan axis to the left and the right
movement of the stick rotates the pan axis to the right.

2015 DJI. All Rights Reserved.

©

14

When

the “Reverse” orientation is selected, the up/down and left/

right controls are switched.

Calibration

“Cali System” should be used if there is perceptible drift on any
axis. The calibration procedure should take approximately 90
seconds to complete.
Selecting “Auto Tune” will automatically adjustment each motor’s
stiffness settings to achieve an optimal balance. This process
should take approximately 20 seconds to complete.
The gimbal cannot be controlled by the Thumb Controller or the
remote controller during calibration. Do not touch or move the
gimbal during either process.

Device Settings

Sensitivity

There are two sensitivity settings for the Thumb Controller: Soft/Hard.

Sleep

If the  Thumb Controller  has been  idle for  longer than  the specied 

amount of time, the OLED display will be turned off.

f

Power Of

If the  Thumb Controller  has been  idle for  longer than  the specied 

amount of time, it will be turned off.

Default Settings

Restores all settings to the factory defaults.

About

Displays the firmware version that is currently installed on the
Thumb Controller.

2015 DJI. All Rights Reserved.

©

15

DJI Assistant App

You can adjust various parameters in the DJI Assistant app.
Turn on the Thumb Controller and the gimbal, then launch the DJI
Assistant app. You can adjust the control speeds in the Wizard menu.

To meet your specic requirements, you can also access advanced 

functions through the Assistant app. In the Control Menu, you can
adjust the Deadband, Maximum Speed, Smoothing, and Controller
Priority.

Speed

Gimbal

0

Pan Axis

0

ilt Axis

T

0 0

Axis

Roll

rack Test

SmoothT

est Pan Speed

T

est Tilt Speed

T
T

est Roll Speed

Control

Speed Adjustment

Thumb
Controller
Remote
Operator

Gimbal Control

Controller Priority: If both the Thumb Controller and a remote
controller simultaneously send control signals to the gimbal,
the input from the selected controller will take priority will
control the device.
Refer to the Ronin/Ronin-M User Manual for more details.

2015 DJI. All Rights Reserved.

©

16

Tuning

N/A

Accel

Deadband

Wizard

？

0

0

0

0

0

Pan

ilt

T

15

40

1515

Viewer

More

Mode：

Control

Wizard

Deadband Maximum Speed

Smoothing Endpoint

Channels Settings

Gimbal Control V

iewer

More

DJI PC/MAC

The DJI PC/MAC Assistant allows you to tune the Thumb Controller

and update its rmware.

The tuning procedures offered through the DJI Assistant App are
the same as those offered through the DJI PC/MAC Assistant.
There is no need to adjust the settings in both.
The DJI Assistant app and the PC/MAC Assistant program cannot be
connected to the Thumb Controller at the same time. If you are running
the Assistant app on your mobile device, be sure to disconnect the
Micro-USB cable before using the Assistant on a PC/MAC.

Assistant Tuning

Settings

In the Control Menu, you can adjust the Deadband, Maximum
Speed, Smoothing, and Controller Priority.

2015 DJI. All Rights Reserved.

©

17

Updating the

You can  nd  the latest  rmware  version  information on  this  page 
and update the rmware by following the steps below:

1. Us

y
blue.

2. Click “Update.”

Wait

3. 

4. 

Click

5. After the update is complete, turn the Thumb Controller off and

then on again.

6. Repeat this process with the Ronin-M or the

Receiver, depending on your model.

18

Thumb Controller and the Receiver

e the Micro-USB cable to connect the Thumb Controller to

our computer, then wait until the indicator in the Assistant blinks

 for the download to nish.

 “Update” again and then click “Conrm.”

Ronin External

2015 DJI. All Rights Reserved.

©

Ensure that your computer is connected to the internet

 all antivirus programs and network rewalls

Close

Ensure that the device is turned on before beginning the

update process

Do not disconnect the USB cable until the update is complete

If the Thumb Controller fails to update, follow the steps below:

1. Press and hold the override button.

2. Use the USB cable to connect the Thumb Controller to the computer.

3. Now, release the override button and wait for the connection to

be established.

4. Click the

“Update” button after the Thumb Controller has been
successfully connected to the Assistant. The Thumb Controller
will be operate normally after the update is complete.

2015 DJI. All Rights Reserved.

©

19

Specications

T

ype RONIN TC1

Support Device Ronin, Ronin-M

Operating Frequency 2.415GHz-2.473GHz

Working Current <100mA @ 3.3V

Communication Distance 60m

Battery Life 18h

Standby Life 20h

Operating Temperature -20°~ 50°

Battery Type LiPo

Battery Voltage 3.7V

Battery Capacity 1150mAh

Charge Time 2h

Weight 50g

Size 2.7×1.4×0.9 in. (68×36×23 mm)

Mounting Bracket Diameter 1.0 in. or 1.2 in. (25 mm or 30 mm)

Display

2015 DJI. All Rights Reserved.

©

20

White OLED, 0.96 inch,
Dots: 128×64

The content is subject to change.

Download the latest version from
http://www.dji.com/product/

If you have any questions about this document, please contact DJI
by sending a message to

2015 DJI. All Rights Reserved.

©

[e-mail]

.

Due to the used enclosure material, the product shall only be connected to a USB
Interface of version 2.0 or higher. The connection to so called power USB is prohibited.

CA

UTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

OSE OF USED BATTERIES ACC OR DING TO THE INST RU CTIONS

DISP

Hereby, SZ DJI TECHNOLOGY CO., LTD declares that this device is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.

Power is so low that no RF exposure calculation is needed.
FCC statements:

This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications or changes to this equipment. Such modifications or
changes could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help.

This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired
operation of the device.

Cet appareil est conforme avec Industrie Canada RSS exemptes de licence standard(s).

Son fonctionnement est soumis aux deux conditions suivantes:

(1) cet appareil ne peut pas provoquer d'interférences, et

(2) c et appar eil doi t ac cepter t oute i nterférence, y c ompris c elles pouv ant causer un

mauvais fonctionnement de l'appareil.

RONIN RX could be powered DC 12V-16V (powered by RONIN through

CAN port with a 4-Pin Cable)or DC 5V (powered by PC through USB port)

RONIN is powered by intelligent battery, the battery capacity is 3400mAh,

voltage is 14.8VDC, charge the intelligent battery only with DJI approved chargers with

the battery moving off from ronion.