DJI SRW-60G
User Manual
2016.06
V1.0
Disclaimer and Warning
WARNING
CAUTION
NOTICE
TIPS
Congratulations on purchasing your new DJITM product. The information in this document
affects your safety and your legal rights and responsibilities. Read this entire document
carefully to ensure proper conguration before use. Failure to read and follow instructions
and warnings in this document may result in serious injury to yourself or others, or damage
to your DJI product or damage to other objects in the vicinity. This User Manual and all other
collateral documents are subject to change at the sole discretion of DJI. For up-to-date
product information, visit http://www.dji.com and click on the product page for this product.
By using this product, you hereby signify that you have read this disclaimer and warning
carefully and that you understand and agree to abide by the terms and conditions herein.
You agree that you are solely responsible for your own conduct while using this product,
and for any consequences thereof. You agree to use this product only for purposes that
are proper and in accordance with all applicable laws, rules, and regulations, and all terms,
precautions, practices, policies and guidelines DJI has made and may make available.
DJI accepts no liability for damage, injury or any legal responsibility incurred directly or
indirectly from the use of this product. The user shall observe safe and lawful practices
including, but not limited to, those set forth in this User Manual.
DJI is a trademark of SZ DJI Technology Co., Ltd. (abbreviated as “DJI”) and its aliated
companies. Names of products, brands, etc., appearing in this manual are trademarks or
registered trademarks of their respective owner companies.
Using this Manual
Legend
Warning: Failure to properly follow procedures may result in property damage,
collateral damage, and serious or supercial injury.
Caution: Failure to properly follow procedures may result in property damage and
serious injury.
Notice: Failure to properly follow procedures may result in property damage, a
small possiblity of injury, or no possibility of injury.
Tips
2
2016 DJI All Rights Reserved.
©
Before You Begin
Make sure all the parts listed in the In the Box section below are included in the package.
Read this entire User Manual and watch the informational and tutorial videos on the product
page of DJI’s ocial website (http://www.dji.com). Read the disclaimers and warnings above
to understand your legal rights and responsibilities. If you have any questions or problems
during the installation, maintenance or use of this product, please contact DJI or a DJI
authorized dealer.
In the Box
Transmitter ×1 Receiver ×1 Power Cable for Transmitter ×1
Power Cable for Receiver ×1 USB Cable ×2 Screw (M3×5.5) ×4
Introduction
The DJI SRW-60G is a short range wireless video link, which can transmit real time HD video
or images for up to 10 meters. Containing both a transmitter and a receiver, it can also be
used with the Ronin series of handheld gimbals. Convenient video transmission in a meeting
room or at home are also a breeze with the SRW-60G.
2016 DJI All Rights Reserved.
©
3
SRW-60G Diagram
Transmitter
1. HDMI Port
For connecting to the HDMI output
for HDMI transmission.
2. Gimbal Mounting Adapter
For mounting to a Ronin-MX or
Ronin-M. The adapter can be
removed when not used with the
Ronin-MX or Ronin-M.
3. Cable Slot
For fastening the cable in position.
4. Link Button
For linking to the Receiver.
5. Micro USB Port
For rmware upgrades and power
supply.
7
1
2
6. Power Port
For power supply.
7. Status LED
Indicates the communication status with
the Receiver.
6
5
4
3
Receiver
1. Micro USB Port
For rmware upgrades and power
supply.
2. Power Port
For power supply.
3. HDMI Port
For connecting to HDMI input for
HDMI transmission.
4. Mounting Adapter
The adapter can be removed.
4
2016 DJI All Rights Reserved.
©
1
2
3
4
5. Status LED
Indicates the communication status
with the Transmitter.
5
Usage
NOTICE
Using the SRW-60G with a Ronin Series Gimbal
1. Loosen the screw of the clamp on the gimbal mounting adapter of the Transmitter. Then
attach the Transmitter to the arm of the Ronin-MX or Ronin-M and tighten the screw.
2. Link the HDMI Ports of the Transmitter and the camera by using a soft and exible HDMI
cable (not provided).
3. Connect the Power Port on the Transmitter to the CAN1 Port (or the USB port) of the
Ronin-MX by using the provided transmitter power cable.
CAN1 Port
USB Port
In order to avoid obstructing any gimbal movements, the cables can be
attached in the cable slot.
2016 DJI All Rights Reserved.
©
5
4. If using a Ronin, remove the gimbal mounting adapter and stick the Transmitter onto the
NOTICE
NOTICE
Ronin or your camera.
Antenna Position
5. Remove the mounting adapter and mount the Receiver in place.
Antenna Position
Ensure both the Transmitter and Receiver are not obstructed during use.
Using the SRW-60G in a Meeting Room or at Home
1. Remove the mounting adapters.
2. Connect the HDMI output and input to the
Transmitter and Receiver separately.
3. Connect the USB ports on both the Transmitter and
Receiver to an external power supply.
The USB port operation voltage is 5 V (DC).
6
2016 DJI All Rights Reserved.
©
Linking
The Transmitter is linked to the Receiver before delivery. Linking is only required when
using a new Transmitter or Receiver.
Ensure the Transmitter and Receiver are properly connected to the HDMI device
before linking to avoid failure.
How to link
Press the Link button on the Transmitter once. The linking process will complete in
approximately 10 seconds.
Status LED Descriptions
Transmitter Status LED Receiver Status LED Description
Blinks red
......
slowly
Blinks red
......
quickly
Blinks green
......
quickly
— Solid green — Solid green
TIPS
If the linking process does not complete after 15 seconds, check the HDMI
connection on both the Transmitter and Receiver.
......
......
......
Blinks green
slowly
Blinks green
quickly
Blinks green
quickly
The device is not linked and not
connected to the HDMI device.
Linking but the Transmitter is not
connected to the HDMI device.
Linking in progress
Linking successful and working
normally
2016 DJI All Rights Reserved.
©
7
Specications
General
Max Transmission Distance 10 m (unobstructed)
Max Transmitter Power (EIRP) Transmitter: 17 dBm, Receiver: 30 dBm
Receiver Sensitivity -72 dBm
Operating Frequency 57 GHz to 64 GHz
Video Output Port HDMI
Video Resolution From 480
Latency
Transmitter
Dimensions 78 mm (L) × 33 mm (W) × 16 mm (H)
Weight 46 g
Antenna Gain LRP Mode: 5 dBi; MRP Mode: 9 dBi
Operating Voltage (DC) 7.4-12 V (CAN Port) or 5 V (USB Port)
Max Consumption 1.5 W
Operating Temperature 32° to 104° F (0° to 40° C)
Antenna Type Built-in Antenna
Receiver
Dimensions 65 mm (L) × 46 mm (W) × 14 mm (H)
Weight 47 g
Antenna Gain 16 dBi
Operating Voltage (DC) 7.4-18 V (CAN Port) or 5 V (USB Port)
Max Consumption 2.5 W
Operating Temperature 32° to 104° F (0° to 40° C)
Antenna Type Built-in Antenna
8
2016 DJI All Rights Reserved.
©
< 1 ms
i /
576 i to 1080p 60Hz
FCC Compliance Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Informatio
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to
the antenna shall not be less than 20cm during normal operation.
n
IC RSS Warning
This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference,including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
2016 DJI All Rights Reserved.
©
9
IC Radiation Exposure Statement:
This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm between the radiator&
your body.
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
KCC Warning Message
“해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 .”
“해당 무선설비는 운용 중 전파혼신 가능성이 있음”
EU Compliance Statement
SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential
requirements and other relevant provisions of the R&TTE Directive.
A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance
EU contact address: DJI GmbH, Industrie Strasse. 12, 97618, Niederlauer, Germany
10
2016 DJI All Rights Reserved.
©
DJI Support
http://www.dji.com/support
The content is subject to change.
Download the latest version from
http://www.dji.com/product/ronin-mx
If you have any questions about this document, please contact DJI
by sending a message to DocSupport@dji.com.
TM
is a trademark of DJI.
RONIN
Copyright © 2016 DJI All Rights Reserved.
2016 DJI All Rights Reserved.
©
Printed in China.
11
Loading...