System X Series Matrix X, M3216AX, M3216XX, M1608AX, M3208AX Installation Manual
Series Matrix X
M3216AX
M3216XX
M3208AX
M1608AX
Installation
Manual
2850-00002
SYS E
M
SYSEM
Page 12
Specifications
..........................................................
Page 11
Junction Boxes
................................................................
Page 10
LON® Network Cable Lengths
................................................
Page 10
LON® Network Cables
........................................................
Page 9
Repeater
........................................................................
Page 9
Termination
....................................................................
Page 8
Bus Topology
...................................................................
Page 8
Selection of network Topology
................................................
Page 8
LON® Installation
........................................................
Page 7
Video standard selection
...................................................
Page 7
Rear panel indicator
............................................................
Page 7
Front panel indicator
...........................................................
Page 7
LED indicators
.............................................................
Page 6
First time start
............................................................
Page 6
Other connections
...........................................................
Page 6
Remote Sites
..................................................................
Page 6
Video input- and output expansion using the M3216XX
.......................
Page 6
Video input- and output expansion
............................................
Page 5
Video output expansion
........................................................
Page 5
Video input expansion
.........................................................
Page 4
Video expansion
.............................................................
Page 4
Video connections
.......................................................
Page 4
LON® connection
.............................................................
Page 3
Mains fuse
....................................................................
Page 3
Mains installation
............................................................
Page 3
Unpacking the unit
..........................................................
Page 3
Installation
................................................................
Page 2
Trademarks
...................................................................
Page 2
Approvals
.....................................................................
Page 2
Compatibility
.................................................................
Page 2
Validity
........................................................................
Page 2
Introduction
..............................................................
SYSEM
Introduction
The Series Matrix X consists of a number of video matrix units controlled via LONWORKS®:
Ÿ M3216AX: 32 video inputs / 16 video outputs with loop facilities on both video
inputs and outputs for easy expansion.
Ÿ M3208AX: 32 video inputs / 8 video outputs with loop facilities on both video inputs
and outputs for easy expansion.
Ÿ M1608AX: 16 video inputs / 8 video outputs.
Ÿ M3216XX: Used as an cost saving expansion unit in combination with the M3216AX
only. In an expanded system not all matrix units have cameras or monitors
connected. At these location(s) the M3216XX unit is used which consequently is
equipped with video loop connectors only; no BNC- video connectors are available.
By interconnecting several Matrix X units the number of video inputs and/or outputs is
increased.
The video input terminations can be programmed to 75
Ω or high impedance (Hi-Z).
All settings are selected remotely using the S111SX Node Manager - no settings are
possible on the unit itself, except selection of video standard; either PAL/CCIR (factory
default) or NTSC/RS-170.
Daily operation is carried out via the keyboards Series K111xX.
Validity
This manual cover the Matrix X types M3216AX, M3216XX, M3208AX and M1608AX,
serial number MxxxxxX-0100, where “xxxxx” represents the typenumber, or higher.
The described Remote Site functionality is available with the Node Manager V.2.0 or higher.
Compatibility
The Matrix X is compatible with any SYSTEM X component.
Any device outputting a standard 1 V
pp
video signal may be connected to the video inputs.
Approvals
All electronic equipment can emit, or be sensitive to, induced electromagnetic noise, which
can be conducted the connected wires or transmitted as electromagnetic fields.
Electromagnetic noise can cause malfunction or damage to the equipment.
The Matrix X is -certified and approved in accordance with the EU-directives regarding
Electromagnetic Compatibility, the EMC-directive, and Low Voltage safety, the LVD-directive
with respect to the EN 50081-1 (EMC, emission), the EN 50130-4 (EMC, immunity) and the
EN 60950 (LVD, safety) standards.
WARNING: To fulfil the above regulations make sure to carefully follow
the installation instructions in this manual.
Trademarks
Echelon®, LON® and LONWORKS® are trademarks of Echelon Corporation registered in the
United States of America and other countries.
SYSEM
Installation
Carefully follow the instructions in order not to cause mal-function, damage to the
equipment or humans. Incorrect installation will void the warranty and repairs will
consequently be invoiced according to current scale charges.
All connections are shown on the figures at the fold-out page at the back of this manual.
After all connections have been made installation is completed by switching on the mains
supply. Finally should the Service Pin be activated, however, prior to pressing the Service Pin
make sure the S111SX Node Manager is running and connected to the LON
®
network.
Please note, that it is of outmost importance to keep track of the order in which the various
System X units are activated e.g. by carefully noting the exact time the Service Pin is
activated. This information is crucial when identification and configuration of each unit is
carried out later using the S111SX Node Manager.
Unpacking the unit
Check that the carton box contains the following items:
Ÿ A Matrix X of the correct type (M3216AX, M3216XX, M3208AX or M1608AX).
Ÿ A connector/mounting kit, consisting of:
2 pcs. rack mounting ears.
2 pcs. 9-pin D-SUB connectors.
1 pc. LON
®
connector and cable clamp.
Various screws and washers.
Ÿ Installation manual (this manual).
Carefully check for any sign of damage. Any such damage or parts missing should be
reported to your supplier prior to installation.
Mains installation
The Matrix X must be used with a 3-wire mains connection (2W+PE @ min. 0,75 mm2,
PE=yellow/green, N=blue).
The unit adapts itself to the actual mains voltage; no adjustments are needed.
WARNING: If permanently connected to mains, a readily accessible
disconnect device (mains switch) shall be incorporated in the building
installation wiring.
If pluggable connection to mains has been made, the socket-outlet shall
be present near the equipment and shall be easily accessible.
Mains connection requires installation by an instructed person.
The unit is designed for continous operation.
Mains fuse
A replaceable fuse is located at the power supply board.
Ÿ Designator: F1
Ÿ Rating: F2,5AH, 250V
SYSEM
LON® connection
All SYSTEM X components (nodes) are connected together in a common LONWORKS
®
communication network.
Refer to the drawings at the fold-out page at the end of this manual. Connection is polarity
insensitive. A detailed description of cabling, network topology, temination etc is included in
the LON
®
Installation section located later in this instruction.
Note: If you have no previous experience with LON® , study the LON® Installation section
carefully!
Video connections
Refer to the drawings at the fold-out page at the end of this manual.
The video input terminations can be programmed to 75
Ω or high impedance (Hi-Z) using
the S111SX Node Manager as shown below:
The relevant video signal standard; either PAL/CCIR (factory default) or NTSC/RS-170, is
selected by means of internal jumper(s); refer to the Video standard selection section.
Video expansion
Expansion of video inputs and/or outputs is carried out by combining several Matrix X units
and looping the video connections. For optimum video performance inter-connect the units
as shown on the fold-out page drawings.
On the M3216AX/XX and the M3208AX video looping is established by inter-connecting
the video loop connectors with the special XLOOP cables, available in three different lengths;
350 mm, 675 mm and 1100 mm. Refer to the fold-out page drawings for instructions and
selection of the appropriate cable.
Note: XLOOP cables are not included and should be ordered seperately from your supplier.
The M3216XX is a unit designed as a video expansion unit to be used in combination with
the M3216AX only. It is equipped with video loop connectors only; no BNC- video connectors
are available.
The M1608AX is not equipped with video loop connectors. Video expansion must therefore
be made by inter-connecting the BNC video inputs/outputs using BNC dual straight
“Y”-adaptors as described below.
SYSEM
Loading...