System Sensor EBI, EBFI User Manual

INSTALLATION AND MAINTENANCE INSTRUCTIONS

OPTIONAL REMOTE

EBI and EBFI
Plug-in Detector Bases

SPECIFICATIONS

Diameter: 6.1˝ (155 mm); EBFI

4.0˝ (102 mm); EBI
Wire Gauge: 12 to 18 AWG (0.9 to 3.25 mm2)

BEFORE INSTALLING

Please thoroughly read the system wiring and installation manuals and the
System Smoke Detector Application Guide, which provides detailed informa­tion on detector spacing, placement, zoning, and special applications.

NOTICE: This manual should be left with the owner/user of this equipment.

MOUNTING

Detector base, Model EBFI (Figure 1A), mounts directly to 31⁄2-inch and 4

-inch octagon boxes, 4-inch square boxes (with or without plaster rings) and
single gang boxes. To mount, remove the decorative ring by turning it in either
direction to unhook the snaps, then separate the ring from the base. Install
the base on the box using the screws supplied with the junction box and the
appropriate mounting slots in the base. Place the decorative ring on the base
and rotate it in either direction until it snaps into place.

Detector base, Model EBI (Figure 1B), mounts to 31⁄2-inch octagon boxes,
4-inch square boxes with plaster rings, and European boxes with 50, 60, and
70 mm screw spacing. Install the base on the box using the screws supplied
with the junction box and the appropriate mounting slots in the base.

FIGURE 1A. EBFI 6 INCH MOUNTING BASE:

I56-3796-001R

3825 Ohio Avenue, St. Charles, Illinois 60174

1.800.SENSOR2; Fax: [phone]
www.systemsensor.com

WIRING

All wiring must be installed in compliance with all applicable local codes and
any special requirements of the authority having jurisdiction, using the proper
wire size.

The conductors used to connect smoke detectors to control panels and acces­sory devices should be color-coded to reduce the likelihood of wiring errors.
Improper connections can prevent a system from responding properly in the
event of a fire. For signal wiring (the wiring between interconnected detec­tors), it is recommended that the wire be no smaller than AWG 18. However,
the screws and clamping plate in the base can accommodate wire sizes up
to AWG 12. If shielded cable is used, the shield connection to and from the
detector must be continuous by using wire nuts, crimping, or soldering, as
appropriate, for a reliable connection.

See Figure 2 for proper base wiring. Make electrical connections by stripping
about 3⁄8 of an inch (10 mm) of insulation from the end of the wire (use strip
gauge molded in base), sliding the bare end of the wire under the clamping
plate, and tightening the clamping plate screw. Do not loop the wire under the
clamping plate. The wiring of the detector base should be checked before the
detector heads are installed in them. The wiring should be checked for conti­nuity and polarity in the base, and dielectric tests should be performed. The
base includes a space for recording the zone, address, and type of detector
being installed. This information is important to set the address of the detector
head that will later be plugged into the base and to verify the type required
for that location.

FIGURE 2. WIRING THE BASES:

FIGURE 1B. EBI 4 INCH MOUNTING BASE:

C0896-01

C0895-01

ANNUNCIATOR

+

CONTROL PANEL

–

LISTED COMPATIBLE

–
+

TERMINAL DEFINITIONS

T1 (+) SLC in/out T3 (–) SLC in/out

T2 (+) SLC in/out T4 LED

OPTIONAL RETURN LOOP

+–

C0366-01

SS-450-009 1 I56-3796-001R

TAMPERPROOF FEATURE

TO REMOVE DETECTOR

FEATURE

STRIPPED WIRE

WIRE WITH SPADE LUG

This detector base also includes an optional tamperproof feature that, when
activated, prevents removal of the detector without the use of a tool. To ac­tivate this feature, simply break off the tab on the lever on the detector base
shown in Figure 3A, and install the detector. To remove the detector from the
base once the tamperproof feature has been activated, place a small-bladed
screwdriver into the small hole on the side of the base and push the plastic
lever (see Figure 3B). This will allow the detector to be rotated counterclock­wise for removal. The tamperproof feature may be defeated by breaking and
removing the plastic lever from the base; however, this prevents the feature
from being used again.

FIGURE 3A:

INSERT SCREWDRIVER HERE

REMOTE ANNUNCIATOR (RA100Z)

The remote annunciator is connected between terminals 3 and 4 using the
spade lug terminal packed with the remote annunciator. The spade lug termi­nal is connected to the base terminal as shown in Figure 4. It is not acceptable
to have three stripped wires under the same wiring terminal unless they are
separated by a washer or equivalent means. The spade lug supplied with the
model RA100Z is considered acceptable. See Figure 2 for proper installation.

FIGURE 4:

FIGURE 3B:

BREAK OFF TIP OF LEVER
TO ACTIVATE TAMPER-PROOF

C0114-00

C0115-00

C0116-00

SS-450-009 2 I56-3796-001R
©2011 System Sensor

Please refer to insert for the Limitations of Fire Alarm Systems