System Logic Semiconductor SL74HC4053 Technical data

Semiconductor

查询HC4053供应商

Analog Multiplexer/Demultiplexer

High-Performance Silicon-Gate CMOS

The SL74HC4053 utilize silicon-gate CMOS technology to achieve
fast propagation delays, low ON resistances, and low OFF leakage
currents. These analog multiplexers/demultiplexers control analog
voltages that may vary across the complete power supply range (from
VCC to VEE).

The Channel-Select inputs determine which one of the Analog
Inputs/Outputs is to be connected, by means of an analog switch, to
the Common Output/Input.When the Enable pin is high, all analog
switches are turned off.

The Channel -Select and Enable inputs are compatible with standard
CMOS outputs; with pullup resistors, they are compatible with
LS/ALSTTL outputs.

• Fast Switching and Propagation Speeds

• Low Crosstalk Between Switches

• Diode Protection on All Inputs/Outputs

• Analog Power Supply Range (VCC-VEE)=2.0 to 12.0 V

• Digital (Control) Power Supply Range (VCC-GND)=2.0 to 6.0 V

• Low Noise

SL74HC4053

ORDERING INFORMATION

SL74HC4053N Plastic

SL74HC4053D SOIC

TA = -55° to 125° C for all packages

PIN ASSIGNMENT

LOGIC DIAGRAM

Triple Single-Pole, Double-Position

Plus Common Off

PIN 16 =V

PIN 7 = VEE

PIN 8 = GND

CC

FUNCTION TABLE

Control Inputs ON

Enable Select Channels

C B A
L L L L Z0 Y0 X0
L L L H Z0 Y0 X1
L L H L Z0 Y1 X0
L L H H Z0 Y1 X1
L H L L Z1 Y0 X0
L H L H Z1 Y0 X1
L H H L Z1 Y1 X0
L H H H Z1 Y1 X1

H X X X None

X = don’t care

SLS

System Logic

SL74HC4053

Semiconductor

MAXIMUM RATINGS*

Symbol Parameter Value Unit

VCC Positive DC Supply Voltage (Referenced to GND)

(Referenced to VEE)

-0.5 to +7.0

-0.5 to +14.0

VEE Negative DC Supply Voltage (Referenced to GND) -7.0 to +0.5 V

VIS Analog Input Voltage V

- 0.5 to VCC+0.5 V

EE

VIN Digital Input Voltage (Referenced to GND) -1.5 to VCC +1.5 V

I DC Input Current Into or Out of Any Pin ±25 mA

PD Power Dissipation in Still Air, Plastic DIP+

SOIC Package+

750
500

Tstg Storage Temperature -65 to +150 °C

TL Lead Temperature, 1 mm from Case for 10 Seconds

260 °C

(Plastic DIP or SOIC Package)

*

Maximum Ratings are those values beyond which damage to the device may occur.

Functional operation should be restricted to the Recommended Operating Conditions.
+Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C

SOIC Package: : - 7 mW/°C from 65° to 125°C

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Min Max Unit

VCC Positive Supply Voltage (Referenced to GND)

(Referenced to VEE)

2.0

2.0

6.0

12.0

V

mW

V

VEE Negative DC Supply Voltage (Referenced to GND) - 6.0 GND V

VIS Analog Input Voltage VEE VCC V

VIN Digital Input Voltage (Referenced to GND) GND VCC V

*

V

Static or Dynamic Voltage Across Switch - 1.2 V

IO

TA Operating Temperature, All Package Types -55 +125 °C

tr, tf Input Rise and Fall Time (Channel Select

or Enable Inputs)

*

For voltage drops across the switch greater than 1.2 V (switch on), excessive VCC current may be drawn;

VCC =2.0 V
VCC =4.5 V
V

=6.0 V

CC

0
0
0

1000

500
400

ns

i. e., the current out of the switch may contain both VCC and switch input components. The reliability of the
device will be unaffected unless the Maximum Ratings are exceeded.

This device contains protection circuitry to guard against damage due to high static voltages or electric
fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated
voltages to this high-impedance circuit. For proper operation, VIN and V

should be constrained to the range

OUT

indicated in the Recommended Operating Conditions..

Unused digital input pins must always be tied to an appropriate logic voltage level (e.g., either GND or VCC).

Unused Analog I/O pins may be left open or terminated.

System Logic

SLS

SL74HC4053

Semiconductor

DC ELECTRICAL CHARACTERISTICS Digital Section (Voltages Referenced to GND) V

Except Where Noted

VCC Guaranteed Limit

=GND,

EE

Symbol Parameter Test Conditions V 25 °C to

-55°C

VIH Minimum High-Level

Input Voltage, Channel ­Select or Enable Inputs

VIL Maximum Low -Level

Input Voltage, Channel ­Select or Enable Inputs

IIN Maximum Input

Leakage Current,

RON = Per Spec 2.0

4.5

6.0

RON = Per Spec 2.0

4.5

6.0

VIN=VCC or GND,

6.0 ±0.1 ±1.0 ±1.0 µA

VEE=-6.0 V

1.5

3.15

4.2

0.3

0.9

1.2

≤85

°C

1.5

3.15

4.2

0.3

0.9

1.2

Channel-Select or
Enable Inputs

ICC Maximum Quiescent

Supply Current
(per Package)

Channel Select = VCC or GND
Enable = VCC or GND
V

= VCC or GND

IS

VIO= 0 V VEE = GND
VEE = -6.0

6.0

6.0

2
8

20
80

DC ELECTRICAL CHARACTERISTICS Analog Section

VCC VEE Guaranteed Limit

Symbol Parameter Test Conditions V V 25 °C

to

-55°C

≤85

°C

≤125

°C

1.5

3.15

4.2

0.3

0.9

1.2

40

160

≤125

°C

Unit

V

V

µA

Unit

RON Maximum “ON” Resistance VIN=VIL or V

V

= VCC or V

IS

IS ≤ 2.0 mA(Figure 1)

VIN=VIL or V

V

= VCC or VEE

IS

(Endpoints)
IS ≤ 2.0 mA(Figure 1)

∆RON Maximum Difference in

“ON” Resistance Between
Any Two Channels in the

VIN=VIL or V
V

= 1/2 (VCC- VEE)

IS

IS ≤ 2.0 mA

Same Package

I

Maximum Off- Channel

OFF

Leakage Current, Any One
Channel

Maximum Off- Channel

Leakage Current, Common
Channel

ION Maximum On- Channel

Leakage Current, Channel to
Channel

VIN=VIL or V
V

= VCC- V

IO

Switch Off (Figure 2)
VIN=VIL or V

VIO= VCC- V
Switch Off (Figure 3)

VIN=VIL or V
Switch to Switch =
VCC- VEE (Figure 5)

EE

EE

IH

IH

IH

IH

IH

IH

EE

4.5

0.0

4.5

-4.5

6.0

-6.0

4.5

0.0

4.5

-4.5

6.0

-6.0

4.5

0.0

4.5

6.0

-4.5

-6.0

190
120
100

150
100

80
30

12
10

240

280

150

170

125

140

190

230

125

140

100

35
15
12

115

40
18
14

Ω

Ω

6.0 -6.0 0.1 0.5 1.0 µA

6.0 -6.0 0.1 1.0 2.0

6.0 -6.0 0.1 1.0 2.0 µA

SLS

System Logic