Systemline 7
NetServer & Mini NetServer
Systemline 7 NetServer & Systemline 7 Mini NetServer
Instruction Manual
2
Important safety instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarised or grounding-type plug. A polarised plug
has two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer
12. Use only with the cart, stand, tripod, bracket or table specied by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.
WARNINGS
To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.
This apparatus shall not be exposed to dripping or splashing and no objects lled with liquids,
such as vases, shall be placed on the apparatus.
Apparatus with CLASS1 construction shall be connected to a MAINS socket outlet with a
protective earthing connection.
3
Instructions de sécurité importantes
1. Veuillez lire ces instructions.
2. Veuillez conserver ces instructions.
3. Veuillez prendre connaissance de tous les avertissements.
4. Veuillez suivre toutes les instructions.
5. N’utilisez pas cet appareil a proximite de l’eau.
6. Nettoyez uniquement avec un chion sec.
7. N’obstruez pas les grilles de ventilation. Suivez attentivement les instructions du fabricant lors
de l’installation.
8. N’installez pas cet appareil a proximite d’une source de chaleur telle que des radiateurs, des
bouches d’air chaud, des fours, ou tout autre appareil (y compris des amplicateurs) produisant
de la chaleur.
9. Ne supprimez pas la securite apportee par la prise polarisee ou de type B. Une prise polarisee
possede deux broches, dont une plus large que l’autre. Une prise de type B possede deux broches
et une che terre. La broche la plus large ou la che terre sont la pour votre securite. Si la prise
fournie ne convient pas, adressez-vous a un electricien pour une mise aux normes de votre
installation electrique.
10. Evitez de marcher sur le cordon d’alimentation ou de le pincer, en particulier, a l’extremite du
cordon, de la prise et a la sortie de l’appareil.
11. Utilisez uniquement des accessoires species par le fabricant.
12. Utilisez uniquement les chariots, pieds, tripodes, supports ou les tables recommandes par
le fabricant ou vendus avec l’appareil. Si vous utilisez un chariot, faites tres attention lors du
transport de l’appareil et evitez de le faire tomber pour ne pas vous blesser.
13. Debranchez cet appareil en cas d’orage ou lorsque vous ne vous en servez pas pendant une
periode prolongee.
14. Pour toute reparation, adressez-vous a un professionnel. Faites reparer cet appareil pour des
dommages de n’importe quelle nature : cordon d’alimentation abime, liquide ou objet introduit
dans l’appareil, exposition a la pluie ou a l’humidite, fonctionnement inhabituel, chutes diverses.
AVERTISSEMENT
An de diminuer les risques d’incendie ou de choc electrique, conservez cet appareil a l’abri de la
pluie et de l’humidite.
Evitez toute eclaboussure et ne posez pas d’objets contenant des liquides, comme des vases, sur
cet appareil.
L’appareil de construction de CLASS1 doit être connecté à une prise secteur dotée d’une
protection par mise à la terre.
4
Contents
1.0 Pack contents 5
2.0 Introduction 5
3.0 Mounting and locating the server 5
3.1 NetServer 5
3.2 Mini NetServer 6
4.0 Connections 7
4.1 NetServer 7
4.2 Mini NetServer 7
4.3 Connecting to NetAmps 8
5.0 The NetServer Web Page 9
5.1 Home button 9
5.2 SqueezeBox Server 9
5.3 CD Ripper 10
5.4 FLAC Mirror 10
5.5 Network Conguration 10
5.6 System Conguration 10
5.7 Backup 10
5.8 Conguration Player 11
5.9 Systemline Upgrade 11
6.0 Conguring the system 11
7.0 Backing up the music library 12
8.0 Removing or exchanging NetAmps 12
9.0 Systemline Upgrade Service 14
9.1 BLISS 14
9.2 Supersync 15
10.0 Copying existing digital music library 15
5
1.0 Pack contents
NetServer
1 x NetServer
2 x Mounting brackets with 4 bracket xing screws
1 x Power supply
1 x Mains cable
1 x Quick start instruction manual
Mini NetServer
1 x Mini NetServer
1 x Mounting Bracket
1 x Power supply
1 x Set of mains plug inserts
1 x Quick start instruction manual
2.0 Introduction
The Systemline 7 NetServer acts as the central portal for all S7 zones to receive stored music and
internet based services via the USB connection to the S7 NetAmp. The 160GB Mini NetServer
supports up to 4 zones, 320GB NetServer supports up to 8 zones, the 1TB and 2TB NetServer
supports up to 24 zones. The server comes with pre-loaded software that includes a web page
setup, Logitech Media Server, CD auto ripping and cover art look up, USB back up and Shared
Network folders. The Server has been designed to be centrally located with all NetAmps in the
system to make the multiple USB (up to 24*) connections easy to manage without the need for
additional equipment except an S7 USB Hub.
*1TB (SN2100) and 2TB (SN2200) models support 24 zones; 320GB (SN2030) model supports 8
zones, 160GB (SN2010) supports 4 zones.
3.0 Mounting and locating the server
3.1 NetServer
The server should be located with all the NetAmps in the system and have access to a wired
network connection on RH45 Cat5 or Cat6, connected to the broadband router or network switch.
This in turn should be connected to the router running an active DHCP server.
The NetServer can be mounted in the following ways:
3.1.1 Shelf Mounting
Use the supplied stick-on rubber feet on the underside of the server and place on a shelf. Allow at
least 5cm clearance above the server venting slots.
NetServer (SN2030/SN2100/SN2200)
Mini Netserver (SN2010)
6
Plug the Local Area Network connection into the network with an active DHCP server. Plug a USB
A-B cable into each NetAmp zone. The diagram shows two zones on one NetAmp. If more than 3
zones are required, a separate USB hub can be used. Plug the power supply in and turn on. The
server will boot up automatically.
Always keep a minimum of 5cm clear space on both sides and on top of the NetServer for ventilation.
Do not use the NetServer inside an enclosed space.
3.1.2 Wall Mounting
Use the supplied L-shaped brackets and screws and x the brackets to the sides of the server. Use
the xing points on the brackets to x to the wall using suitable xings (not supplied). Leave at
least 5cm in front of the server for ventilation.
3.2 Mini NetServer
3.2.1 Shelf Mounting
Use the supplied stick on rubber feet on the underside of the server and place on a shelf. Allow at
least 5cm clearance above the server venting slots.
3.2.2 Wall Mounting
Use the supplied bracket and x it to the wall using suitable xings for the wall type (not
supplied). Slot the Mini NetServer onto the bracket. Ensure that the server is located in the correct
orientation; there is an arrow on the back of the server showing you the correct orientation.
7
4.0 Connections
4.1 NetServer
1. Local Area Network (LAN) Ethernet RJ45
2. DC power input
3. USB 2.0
4. HDMI monitor out – not used with Systemline 7
5. VGA monitor out – not used with Systemline 7
6. Microphone in – not used with Systemline 7
7. Audio out – not used with Systemline 7
8. RS232 Serial – not used with Systemline 7
9. RS232 Serial – not used with Systemline 7
4.2 Mini NetServer
1. Local Area Network (LAN) Ethernet RJ45
2. DC power input
3. USB 3.0
4. HDMI monitor out – not used with Systmeline 7
5. High power USB3.0 (can be used with USB CD drive)
6. Mini display port – not used with Systemline 7
12 3
5
76
9
4
8
SS
HDMI
SSSS
314 62 35
8
4.3 Connecting to NetAmps
The server requires a wired LAN connection to the network with a router and DHCP sever. Each S7
zone requires one USB connection from the server to the NetAmp. A USB hub is required if more
than three zones are being used in the system as there are only three USB ports on the server
itself.
Please note: It is important that you connect the USB cables and switch the NetAmps on before the
NetServer when rst installing.
9
5.0 The NetServer Web Page
Once booted up you can nd the IP address of the NetServer using a FREE App called Fing. Run a
scan of the network and look for the IP address of S7_NetServer.
Type the IP address into a browser and open up the web set up page.
e.g. enter 192.168.0.250
5.1 Home button
The home screen shows you the current status of the server including the software
version and available storage space for music.
5.2 SqueezeBox Server
This starts a new web page for the Logitech Media Server (LMS) web interface. As
Systemline 7 uses an embedded LMS, this web interface becomes available and
was designed as a web control for Squeezebox systems. S7 is dierent to standard
Squeezebox systems as it uses the NetAmp for volume control and zone naming
which does not appear in the LMS web page.
This LMS web page is not recommended to be used with S7 as the zone names will
appear as numbers which correspond to the unique USB number on each NetAmp
connection, and the volume control will not operate the NetAmp.
S7 installers will use this page as a step to Settings where the LMS can be congured
for plugins and mysqueezebox.com acount services.
There is a separate document titled S7 Plugins that details adding plugin services to
the server.
10
5.3 CD Ripper
The CD ripper software is embedded in the server, you will need a USB optical drive
plugged into a USB port of the server. It is recommended that you use a USB CD drive
with a motorised drawer or eject function so that the server can eject a CD when it is
nished ripping.
The CD ripping software is designed so that you simply insert the audio CD into the
drive, the server then scans the disc, looks up the meta-data and starts the ripping
process.
This page will show you the status of the CD rip, the details of meta-data and the
status of the FLAC encoding.
Any CD will be ripped as FLAC in the folder \les\music\ac
5.4 FLAC Mirror
If you wish the CD ripper to create an mp3 le in addition to FLAC then you can set it
here. Tick the Enable automatic mp3 mirroring and set the mp3 bitrate that you would
like to use. The 320Kbit/s is the highest quality but takes up more space.
You can convert all les in the FLAC folder to mp3 after ripping or transfer has taken
place. Simply press start mp3 mirroring and the server will transcode and copy all les
and folders.
The server also supports ALAC in the same way. If you select this then the server will
create a new m4a folder \les\music\m4a and transcode all FLAC to this folder.
5.5 Network Conguration
You can set a static IP address here with all the correct Subnet Mask, Gateway and DNS
settings. If you are using NetAmps with a 3rd party control then you should set a xed
IP address here. See section 6.0 for details on conguring the network.
5.6 System Conguration
You can change the time zone here, the default is Europe/London. Make sure you set this
correctlty or the alarm clock functions may not work at the right time. You can also
reboot or power down the server here. See section 6.0 for further information.
5.7 Backup
If you plug in a USB hard drive with enough storage space, the page will give you an option to
back up the music library. Doing so will format the drive, name the folder and copy all
content to the USB drive. See section 7.0 for further information.
5.8 Conguration Player
11
Each NetAmp USB connection is listed here. The Name is the unique USB serial number of the
NetAmp USB socket which is set at the factory, and will correspond to the number
shown on the NetAmp web page Source Setup. The server will allocate a unique and
random MAC address to each USB connection, this is 6 sets of two characters (0-9 and
1-f) and is shown in the table. The server also shows which connections are active by
a 1 or 0, as it retains connection information. You can update this table by pressing
Refresh & submit.
Each time the server is rebooted or the Refresh & submit button is used, the current
active USB connections are submitted to the Logitech Media Server as available
zones.
It is possible to delete or edit the allocated zone’s MAC address, see section 8.0.
The server table of 4 active NetAmp USB connections.
5.9 Systemline Upgrade
You can upload new software on the server here and also add additional software services. To
upload new server software, simply press Start Upgrade. The log below will show your
progress and also verify that new software is available.
To install additional software such as BLISS simply press Install next to the required
service.
See section 9.0 for details on additional optional software services.
6.0 Conguring the system
When you rst connect your S7 Server to a network the server will obtain its IP address
automatically via DHCP (Dynamic Host Conguration Protocol). For S7 to function well, you must
give the NetServer a static IP address. We would recommend you go into your routers settings
and limit the DHCP range to 200 addresses, for example the DHCP range could be 192.168.1.2
to 192.168.1.200 this would then give out 199 IP addresses automatically. Then 192.168.1.201 to
192.168.1.254 would be xed, leaving you with 53 static manual IP addresses that will never be
given out to devices.
You must make sure that your Static IP is inside the range of your router. The usual range for home
networks in the UK is 192.168.1.2 to 192.168.1.254 or 192.168.0.2 to 192.168.0.254. So this means
that the router can have 253 devices attached.
1. Pick a IP address that is free and not inside the DHCP range and enter into static IP address
12
box.
2. Enter the subnet mask – usually 255.255.255.0.
3. Enter the gateway, this is the IP address of the router.
4. The DNS settings can be left blank or you can select your own DNS servers, if you leave them
blank the server will automatically nd its own DNS.
5. Once you are happy with your settings simply press submit, and the server will re-boot and
after a few minutes you will need to log in with your new IP address.
6. To nd your Network settings
If you are using a Windows PC go to start menu type CMD into windows search and press return,
then type ipcong and you will see IP address of your PC, Subnet mask and Gateway.
If you are using a mac simply go to the apple logo at the top right of your desktop then select
system preferences then Network. You will see the subnet mask and the gateway listed here.
Warning: Please ensure you apply a correct and valid IP address, otherwise the system will not operate
correctly and you will not be able to easily discover and connect to it.
7.0 Backing up the music library
If you plug a USB hard drive into the Server you will be able to back up stored music. The size of
the hard drive inserted must be larger than 16GB but also larger than the total amount of stored
music. The amount of storage used can be seen on the S7 Server home page. It is recommended
that you insert a blank Hard drive as when you format all the data will be wiped and the right le
structure will be installed.
1. Insert USB Hard drive (Larger than 16GB)
2. Select Backup page from S7 server web page
3. Select Format Drive
4. Select Back up to USB
The S7 Server will start backing up all the stored music and give you progress status on this page.
The time the process takes will depend on the amount of data stored. Once it has nished the
progress report will say ‘Task complete. You can now remove the hard drive’.
Inserting this drive into a PC or a Mac will allow you to see the backed up les. This is for personal use
only.
Warning: When backing up the S7 Server will become slow to respond.
8.0 Removing or exchanging NetAmps
If you need to exchange an S7 NetAmp for some reason, then you may need to copy the
associated MAC addresses from one NetAmp being removed to a replacement unit. This is
important if you have another 3rd party control system selecting favourites or opening up the
S7 App and selecting the zone automatically. All these functions require the use of the zone MAC
address, and if you simply exchange one NetAmp with another, the NetServer will allocate a new
set of MAC addresses and your 3rd party system will no longer control these zones.
It is quite easy to replace a NetAmp and copy the MAC addresses from one to another.
13
1. Disconnect the NetAmp to be removed from the server, browse to the server Congure Player
page so that you can see all active zones, and press Refresh & submit
You will see that the two connections associated with the NetAmp to be replaced have
changed their state to inactive (0). In this example the USB connections are 000065 and
000066.
2. Plug in the replacement NetAmp, making sure the two USB cables are plugged in, and
switch on. Once booted up press Refresh & Submit and you should see the two new NetAmp
zones appear as active. In this case 000049 and 000050 and have been allocated new MAC
addresses.
3. You now need to copy the MAC address from the old unit into the new unit. Highlight and
copy the lower number rst. Now press Edit next to the lower number of the new zone and
paste the MAC address, overwriting the current MAC address and press Submit.
14
4. Repeat the process for the higher USB number so that the new NetAmp has the same MAC
addresses as the old one.
5. To nish o, press Edit on the zones no longer being used and delete them so that only the
remaining zones are left shown. Finally press Refresh & Submit.
6. You should nd that any 3rd party control system is left unaected as long as you congure
the same IP addresses and zone name etc. as the previous NetAmp.
9.0 Systemline Upgrade Service
You can enhance the power of the S7 NetServer by installing additional software services listed in
the Systemline Upgrade page.
9.1 BLISS
BLISS is a software package designed by Elsten Software Limited which will give the Systemline S7
server the following additional functions:
• Album cover art look up
• Album cover art resolution xing
• Album cover art alternative picture option
• Album cover art embedded le
• Custom folder and le organisation
BLISS is a software partner for Systemline7 as it gives very useful automatic album cover art
management when importing media from iTunes. BLISS requires a paid for licence to operate
beyond 100 xes. There is a link to the web site where a licence can be paid for.
Please refer to the separate document S7 Using with iTunes available on the S7 website from the
download section:
http://www.systemline.co.uk/systemline/s7.htm
15
9.2 Supersync
SuperSync software gives Systemline 7 the ability to easily receive a copy of an iTunes library
media and playlist from the host PC or MAC. SuperSync can be added to the S7 NetServer by
selecting it in the Systemline Upgrade page, but must also be installed on the PC or MAC hosting
the iTunes library. The software gives the following useful features:
• Identies the iTunes library on the host PC or MAC and allows easy transfer of the media
onto the S7 NetServer over the Local Area Network
• Identies iTunes playlists and transfers this information to the S7 server, allowing the user
to select these from the S7 App
• Creates a backup of the iTunes library on the S7 server
• S7 still plays all the iTunes media when the PC or MAC is switched o, or disconnected
from the LAN
SuperSync is a software partner for Systemline7 as it gives useful easy transfer of media and
playlists from an iTunes library. SuperSync requires a paid for licence to be entered on the host PC
or MAC and is available from the SuperSync website.
Please refer to the separate document S7 Using with iTunes available on the S7 website from the
download section:
http://www.systemline.co.uk/systemline/s7.html
10.0 Copying existing digital music library
The S7 server acts as a NAS drive, in that you can browse, copy and paste les to its shared folders.
If you have an existing digital music library, you can transfer this into the server.
1. Browse to the server IP address by selecting Computer and typing \\ followed by the server’s
IP address.
e.g. \\192.168.1.120
2. Double click les and then music and nally ac. This is a default media location for the
embedded Logitech Media Server. All music should be transferred into this folder.
16
3. Copy your digital music library into this folder. The example below has a folder structure of
artist / album / le.
4. Once complete, the Logitech Media Server will rescan this location if you have the Auto
Rescan plugin enabled. See the separate document S7 Plugins available in the download
section for Plugin instructions. If not, you can force a rescan of the library from the App
by simply pressing the (i) button next to the Current Music Source at the top of the zone
selection pop up, and then selecting Rescan.
17
Stortford Hall Industrial Park
Dunmow Road
Bishops Stortford
Hertfordshire
CM23 5GZ
United Kingdom
www.armourhome.co.uk
©2015 Armour Home Electrioncs, All rights reserved.
Our policy is one of continuous product improvement. We reserve
the right to change the design and specications without notice.
All information is given in good faith. The manufacturer accepts
no responsibility for errors, omissions or incorrect assumptions.Q15791-IS_r8
Loading...