Systemair TUNE-S Datasheet

Page 1
Air Distribution Products
TUNE-S
Control Damper
Data Sheet
Page 2
2 / 8 | Dampers

Table of Contents

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Ordering Codes . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation, Maintenance & Operation . . . . . . . . . . . . 7
Transport & Storage . . . . . . . . . . . . . . . . . . . . . . 7
Supplement . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Good to know
Current information on all products is available at design.systemair.com
Page 3
Dampers | 3 / 8

Description

Tune-S is a control and shut off damper for rectangular ducts. It is available in with blade tightness class C4, tested according to EN 1751. It is ideal for use as a control and shut-off damper where different parts of the system need to be airtight separated from each other It can be used on air handling units as outer shut-off damper or with modulating actuator as control damper. The damper can be supplied in a manual or motorized version with position indicator. The maximum recommended duct pressure is 1000 Pa.

Design

TUNE-S units are made from sheet steel frame and Aluminium prole blades. The frame has 20 mm wide anges or tight connection to the duct..
The aerofoil blades are from extruded aluminium. The blades are equipped by rubber gaskets eliminating leakage in closed position. The blade axe are sitting in self lubricating bearings which are connected together by a cog - rod combination to assure a smooth ratio and transition from blade to blade.
Page 4
4 / 8 | Dampers

Dimensions

H
H+40
Fig. 1: Dimensions of TUNE-S with handle for manual adjustment
W
W+40128
H
H+40
70
140
100
Fig. 2: Dimensions of TUNE-S with actuator
NOTE: For the type M0 the actuator is not included.
W
W+40128
70
140
Page 5
Dampers | 5 / 8
Tab. 1: Dimensions of TUNE-S
W (mm)
200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200
100 2,00 2,24 2,42 2,61 2,80 2,99 3,18 3,36 3,55
150 2,58 2,84 3,10 3,36 3,62 3,88 4,14 4,40 4,66 4,92
200 2,76 2,98 3,21 3,44 3,67 3,90 4,15 4,45 4,70 4,99 5,20 5,40 5,62 5,85 5,98
250 3,60 3,90 4,20 4,50 4,80 5,10 5,42 5,72 6,03 6,34 6,65 6,96 7,27 7,58 7,89
300 4,00 4,26 4,52 4,90 5,20 5,86 6,00 6,28 6,53 6,76 7,01 7,30 7,60 7,95 8,23 8,49 8,76
350 4,69 5,03 5,37 5,71 6,05 6,39 6,56 6,73 7,07 7,41 7,75 8,09 8,43 8,77 9,11 9,47 9,80 10,32
400 5,42 5,75 6,09 6,43 6,63 6,78 7,12 7,45 7,79 7,12 8,46 8,83 9,14 9,51 9,86 10,38 10,65
450 6,65 7,00 7,35 7,70 8,05 8,40 8,75 9,10 9,45 9,78 10,06 10,40 10,75 11,12 11,46 11,82
500 7,05 7,39 7,75 8,11 8,47 8,83 9,14 9,49 9,85 10,12 10,52 10,82 11,18 11,52 11,89
550 8,35 8,65 8,95 9,25 9,55 9,85 10,15 10,45 10,75 11,05 11,35 11,65 11,95 12,25
H (mm)
600 8,79 9,15 9,51 9,87 10,23 10,59 10,95 11,31 11,68 12,04 12,40 12,76 13,02
650 10,02 10,27 10,63 10,99 11,35 11,71 12,07 12,43 12,79 13,15 13,51 13,87
700 10,35 10,84 11,30 11,76 12,22 12,68 13,14 13,60 14,09 14,58 15,07
750 10,95 11,40 11,90 12,40 12,90 13,40 13,90 14,40 14,90 15,40
800 12,56 13,08 13,60 14,12 14,64 15,16 15,68 16,20 16,72
850 13,18 13,68 14,18 14,68 15,18 15,68 16,18 16,68
900 13,83 14,40 14,97 15,54 16,11 16,68 17,15
950 15,60 16,25 16,90 17,55 18,20 18,85
1000 16,40 17,06 17,72 18,38 19,04
Legend
6,43 kg Weight of the damper without actuator/Torque 5 Nm
9,54 kg Weight of the damper without actuator/Torque 10 Nm
Page 6
6 / 8 | Dampers

Ordering Codes

TUNE-S- -
Size (mm) W × H 200 ... 1200 × 100 ... 1000
Handle for manual adjustment H
Preparation for actuator M0
230 V actuator M1
24 V actuator M2
24 V, 0 V ... 10 V continuous actuator M3
230 V spring actuator M4
24 V spring actuator M5
Positioning type 24 V, 0 V ... 10 V continuous spring actuator M6
Example of Ordering Code
TUNE-S-600×200-M3
Control damper TUNE-S with 600 mm width and 200 mm height, actuator with 24 V power supply, continuous control signal DC 0 V ... 10 V.
Page 7
Dampers | 7 / 8

Installation, Maintenance & Operation

Tune-S is mounted into the ductwork by a standard ange. The xing bolts, nuts, clips and gaskets shall be delivered
by the installation company. The damper cannot be installed carrying any mechanical loads from other structures.
Dry indoor conditions with an operation temperature range of -20°C to +70°C in the duct, -20 °C ... +50 °C on the actuator with relative humidity up to 95% non-condensing conditions.

Transport & Storage

Dry indoor conditions with a temperature range of -20°C to +50°C.

Supplement

Any deviations from the technical specications contained herein and the terms should be discussed with the manufacturer. We reserve the right to make any changes to the product without prior notice, provided that these changes do not affect the quality of the product and the required parameters.
Current information on all products is available on
Systemair DESIGN.
Page 8
www.systemair.com
Systemair Production a.s. · DataSheet_TUNE-S_EN_202008
Loading...