Sysgration NCS50SP, NCS50DC Users Manual
RV CONTROL AND MONITORING SYSTEM
Installation and Operation Manual
Patent # 9,679,644
Important Safety Information
Read the iN-Command Manual, and these warnings and instructions carefully before using this product. Failure to follow the use
instructions in this owner’s manual, or improper use of the Mobile Application, Display Commander and/or Body Control Module, could
result in personal injury, including death.
Do not operate while vehicle is being driven
used while the vehicle is being driven. Use of the Mobile Application, Display Commander and/or Body Control Module while the vehicle
is being driven is dangerous and may cause personal injury or property damage.
For adult use only.
to be used by persons under the age of 18. Use by children may cause personal injury or property damage.
Operate only when you have a clear line of sight.
slides), unless you have a clear line of sight to the moving part. The Mobile Application, Display Commander or Body Control Module
may be used only if you are giving instructions to, and receiving instructions from, another person at least age 18 or older who can clearly
see the moving part. Failure to follow these instructions may result in serious personal injury or property damage.
Do not operate under the inuence of alcohol or drugs.
Module while under the inuence of alcohol or drugs. Doing so may result in personal injury or property damage.
Avoid moisture.
Use recommended accessories.
accessories.
The Mobile Application, Display Commander and Body Control Module are intended for adult use only, and are not
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture.
To reduce the risk of re or electric shock and annoying interference, use only the recommended
. The Mobile Application, Display Commander and/or Body Control Module should not be
Do not operate any moving parts (including, but not limited to, awnings, jacks and
Do not operate the Mobile Application, Display Commander or Body Control
• TABLE OF CONTENTS
TABLE OF CONTENTS ...........................................................3
INTRODUCTION .....................................................................4
Thank You! .............................................................................4
Features .................................................................................4
Precautions ............................................................................4
Packing List ............................................................................4
INSTALLATION ........................................................................5
Tools and Supplies .................................................................5
Disconnecting the Battery ......................................................5
Selecting the Mounting Location ............................................ 5
Mounting the Display Commander (DC) ................................5
Mounting the Switch Plate (SP) .............................................5
WIRING ...................................................................................6
APP SETUP MENU LIST .........................................................7
TRAVEL LOCKOUT (SAFETY) ..............................................8
TROUBLE SHOOTING ............................................................9
SWITCH PLATE BUTTONS ..................................................10
DISPLAY COMMANDER BUTTONS .....................................10
SPECIFICATIONS .................................................................11
Federal Communications Commission (FCC) Statement ...... 11
MOBILE DEVICES: ...............................................................12
Pairing Mobile Device to DC/SP ............................................13
NCS50DC/SP FIRMWARE UPDATE* ...................................15
EDIT AND RESET FLOOR PLAN .........................................16
3
• INTRODUCTION
• Thank You!
Thank you for choosing iN-Command. We hope you will nd the instructions in this owner’s manual clear and easy to follow. If you take a few
minutes to look through it, you’ll learn how to use all the features of your
new iN-Command Lite for maximum enjoyment.
• Features
Features of iN-Command Lite system:
• Simultaneous control by one Android Device or one iOS Device
• Control one Light zone
• Control Awning
• Control Electric Slides
• Control Jacks (non-automatic function)
• Monitor Battery Voltage with Low Voltage Alert
• Precautions
Use the Proper Power Supply.
•
This product is designed to operate with a 12 volt DC, negative ground
battery system (the standard system in a North American vehicle).
Use Authorized Service Centers
•
Do not attempt to disassemble or adjust this precision product; contact
a professional for assistance.
Avoid Moisture.
•
To reduce the risk of re or electric shock, do not expose this equipment
to rain or moisture.
Avoid Cleaning Products.
•
The front of this unit should only be cleaned with a slightly damp cloth.
Do not use cleaning products.
Use Recommended Accessories.
•
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND
ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED
ACCESSORIES.
.
• Packing List
(1) Cover, (1) Thumb Screws (1) Body Control Module (BCM)
(1) Display Commander (DC)
(1) Switch Plate (SP)
4
• INSTALLATION
It’s a good idea to read all of the instructions before beginning the
installation. We recommend having your iN-Command system
installed by a reputable RV dealership
• Tools and Supplies
You will need the following:
• Phillips screwdriver
• #2 square drive bit
• Wire cutters and strippers
• Electrical tape
• Volt meter/test light
• Crimping tool
• Fork Crimp connectors
• 10 gauge wire for power and slide connections
• 14 and 18 gauge wire for all other connections
• Two #8 PH (0.164” x 0.5”) screws for the DC
• Two #8 PH (0.164” x 0.5”) screws for the SP
• Six #8 PH (0.164” x 1.0”) screws for the BCM
• Minimum of 24 gauge wire required to Connect DC To BCM
• Disconnecting the Battery
To prevent a short circuit, be sure to turn off 12V power and remove
the negative (-) battery cable prior to installation.
• Mounting the Display Commander (DC)
• Cut/Drill hole, allowing space below for future programming and
behind for ventilation
• Route wires through the hole and connect
• Attach rear plate with screws
• Check and ensure correct operation
• Snap main unit into plate
• Mount the unit using two #8 PH (0.164” x 0.5”) screws
Wall For Reference
HOLE SIZES
Display Commander (DC) 0.75”
Recommended Cutout
• Mounting the Switch Plate (SP)
• Cut/Drill hole, allowing space below for future programming and
behind for ventilation
• Route wires through the hole and connect
• Check and ensure correct operation
• Mount the unit using two #8 PH (0.164” x 0.5”) screws
• Selecting the Mounting Location
Select a mounting location, taking care to avoid the following:
• Places exposed to heat-radiating appliances such as electric heaters
• Adjacent to other equipment that radiates heat
• Under thermostats
• Poorly-ventilated or dusty places
• Moist or humid locations
5
Wall For Reference
HOLE SIZES
Switch Plate (SP) 1.875”
Recommended Cutout
Loading...