Sysgration AXM 403 Users Manual

Wi rel es s Optical Mouse / Bra n d N a m e : S A N Y O / M odel No. : A XM 403IPM, SYMS-403I

f

p

f

Wireless Optical Mouse

SANYO

AXM403IPM, SYMS-403I

B. Po wer Off Mode :

When you wish to set the mouse to power of
mode, press mouse ID for 3 seconds. The
Optical Led will flash once and then fade out
showing mouse power is already off. Press ID
switch for waking up again .

7. Trouble Shooting:
A. When mouse doesn＇t respond, check the
battery power status, a nd l i nk ID aga in.
B. Be sure the two DC Jacks be connected to
the right respective mouse or receiver DC

sockets

C. Check the battery pole if the optical Led
is still off after inserting batteries.

1. Connectin g wi th Com puter:
The first time you take out this
mouse and receiver from the
packing, Fa ctory Preset ID
enables Plug and Play function.
Plug the R eceive r into PC U S B
Port . Under Win2000 or higher ,
wait for the OS to detec t the RF
device. Under Win98 or lower
installation of driver for the
device is necessa ry.
Insert the batterie s into
the mouse and move it for a while , then it starts
working .

2. Inserting Batteries:

A. Push the battery cover
Compartment backwards
and open it.

conn ected when Low Battery Al ert Led never
fades out.

F. As k for mai nten ance solution fr om you r

retailer and engineer . Personally taking apart

rohibi ted af t er tr ou b le h appen ed .

B. Insert 2 AAA batteries Into
compar tment with cor r ect
orienta tio n .

C. Slide the battery cov er int
the compartment and
close the cover .

3. ID Link:

When Factory ID has been
cha nged or wish to b e changed ,
link ID as
below :

A. Pre ss th e ID bu tton on the
top of the receiver and the
led on it starts blinking .

B. P ress the ID butt on on the
bottom of the mouse .
If b link i ng of that led turns
faste r , ID Link is OK .

! ID linking should be co mpleted within

10 seconds or con nection would be fai l ed

CE Safety Statements

This device has bee tested and found to
comply with the requirements set up in the
council directive on the approximation of the
law of member states relating to EMC
Directi ve 89/336/EEC , Lo w Vo ltage Di rective
73/23/EEC and R&TTE Directive 99/5/EC.

The product has been approved for LVD
and covered the following countries:

Austria, Belgium, D enmark, France,
Finland, Germany, Greece, Iceland,
Ireland, It aly, Lu xembo urg, N eth erlands ,
Norway, Portugal, U.K., Spai n, Swe de n

4. Power Saving Mo de:

A. Suspend Mo de :

Keep mouse stationary for 10 minutes, mouse
will be automatically
set to Suspend Mode. Press left
button to wake up the mouse
again.

This device complies with Part 15 of the FCC rules, operation is subject

to the following two conditions.

（1）This device may not cause harmful interference and,
（2）This device must accept any interference received,

including interference that may cause undesired operation .

This equipment has been tes ted and comply with th e limits for a
class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection. This
equipment generates, uses and can radiated radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful intererence to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation if this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning th e equipment of
and on, the us er is encouraged t o try to correct the interference b y
one or more of the fol lowing mea sur e s:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an o utlet on a circuit different from

that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV

technician for help.

Changes or modifications not expressly approved by the
party

responsible for compliance could void the user＇s authority to
operate the equipment.

The antenna(s) used for this transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter

FCC Note :