RoHS
HD SDI DVR
USER’S MANUAL
harmful interference in which case the user will be required to correct the
Changes or modifications not expressly approved by the party
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FCC INFORMATION : This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
interference at his own expense.
CAUTION :
responsible for compliance could void the user’s authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
CE COMPLIANCE STATEMENT
WARNING: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
- 2 -
- 3 -
Features
This HD SDI(serial digital interface) DVR allows users to have HD level of video surveillance with 720P &
1080P resolution both in live and playback. Unlike megapixel IP cameras and NVR, it doesn’t require IP
related expertise and can be installed under coaxial cabling.
HD SDI DVR with H.264 compression
HD video over coaxial cable : No latency & no loss of frame
120fps(PAL: 100fps) real time @ 720P, 60fps(PAL:50fps) @ 1080P
HDMI, VGA and BNC video outputs
1 internal SATA HDD and E-SATA for external storage
Individual channel setup for recording & network stream (resolution/frame rate)
Event text + image notification to FTP server and E-mail address
Easy network : UPNP (Universal plug & play) support
User control : Up to 20 users can be generated with various access authority
Calendar search, Time search, Event search & Thumbnail search
CMS for multi sites monitoring
Web view monitoring via various browser (IE, Safari, Firefox and more)
Smart phone application (Live, PTZ, Search)
- 4 -
CONTENTS
1. Product Overview
1.1 Packing Contents ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 8
1.2 Front ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 9
1.3 Rear ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 10
2. Installing Product
2.1 Installing HDD ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 13
2.2 Connecting Camera and Audio Device ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 14
2.3 Connecting Monitor ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 14
2.4 Connecting Optional Device ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 15
2.5 Connecting Network ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 15
2.6 Connecting Power Supply ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 15
3.Controlling DVR
3.1 Remote control – basic description ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙
3.2 Remote control – additional description ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙
3.3 Mouse ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙
4. Operation
4.1 Turning On ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 20
4.2 Initial Screen ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 20
4.3 Screen Layout ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 20
5. MENU
16
17
18
5.1 Access to menu ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 23
5.2 Setup Menu ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 23
5.2.1 Display ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 24
5.2.2 Camera ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 25
5.2.3 Record ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 27
- 5 -
5.2.4 Event ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 30
5.2.5 Storage ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 34
5.2.6 Network ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 36
5.2.7 System ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 40
5.3 Search ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙
5.3.1 Search by Time ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 45
5.3.2 Search by Event ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 45
5.3.3 Thumbnail Search ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 45
5.3.4 Backup ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 46
5.3.3 Search mode ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 47
5.4 Other function ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 48
5.4.1 PTZ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 48
5.4.2 Audio ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 49
5.4.3 Log View ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 49
5.5 OSD OFF ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 50
5.6 REC ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 50
5.7 Log Out Control ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 50
Specification ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 51
Trouble shooting ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 52
- 6 -
1. Product Overview
- 7 -
1.1 Packing Contents
When you first open the product, please check out whether there are all contents as follows.
If any of these items is missing or damaged, contact your supplier immediately before using the product.
DVR product Remote control & Battery
Power adaptor and cable Software CD
USB mouse
Screws
User’s Manual HDD power cable & SATA cable
- 8 -
5
7
1.2 Front
Number Name Function
1
2
USB port Connect USB device (mouse or USB stick/HDD)
PWR : Light on when power is on
LED indicator
REC : Light on when DVR is recording
NET : Light on when a user is connected via network
3
4
Direction &
6
Mode Change screen split mode
Menu Access to main menu
Select directions in menu
Selection keys
Play, FF(fast-forward), RW(rewind), stop/pause buttons
ZOOM Access directly to digital zoom mode (in live & playback)
SEARCH Access directly to search menu
- 9 -
10
8
10
1.3 REAR – 4channel
2
1
Number Name Function
1
2
DC 12V Connect power adaptor provided with the product
SENSOR Sensor input port
ALARM Alarm output port
RS-485 PTZ camera control by RS-485 communication
4 6
3
5
7
8
9
3
4
5
6
7
9
AUDIO IN/OUT Connect audio in or out device (such microphone or speaker)
VIDEO OUT Composite video out (BNC type)
VGA VGA output
HDMI HDMI ouput
E-SATA E-SATA port
USB Connect USB device (mouse or USB stick/HDD)
ETHERNET ETHERNET port
HD SDI HD SDI video input
- 10 -
4
10
10
1.3 REAR – 8 channel
2
1
Number Name Function
1
2
3
DC 12V Connect power adaptor provided with the product
SENSOR Sensor input port
ALARM Alarm output port
RS-485 PTZ camera control by RS-485 communication
AUDIO IN/OUT Connect audio in or out device (such microphone or speaker)
3
4
5 6 7 8 9
5
6
7
8
9
VIDEO OUT Composite video out (BNC type)
VGA VGA output
HDMI HDMI ouput
E-SATA E-SATA port
USB Connect USB device (mouse or USB stick/HDD)
ETHERNET ETHERNET port
HD SDI HD SDI video input
- 11 -
2. Installing Product
HD SDI 4ch DVR
SYSTEM CONFIGURATION
- 12 -
2.1. Installing HDD
1 internal HDD can be installed inside the product.
If HDD was not installed in the product, please install HDD first as follows.
Be careful not to be harmed by sharp edges of the product.
(1) Loosen screws on both sides and back to
detach the product cover.
(2) Lift the end of top cover and pull out from
product.
(3) In order to install HDD, you need to upside
down the unit and position HDD onto thebottom
and fix it with provided screws as below.
(4) After connecting HDD onto the bottom of
the unit then connect SATA HDD and power
cable between HDD and main board.
(5) Insert top cover to product as side picture
Them, tighten screws again.
- 13 -
2.2. Connecting camera and audio device
Connect coaxial cable (BNC type) into VIDEO IN port on rear of the product.
HD SDI cabling specification: SMPTE 292M standard, 5C-HFBT or above
Connect RCA cable from microphone into AUDIO IN port on rear of the product.
Connect RCA cable into AUDIO OUT port on rear of the product and into audio device.
HD SDI video input
Audio IN
Audio OUT
2.3 . Connecting monitor
Connect monitors into the video out ports of the product according to interface.
1 x HDMI OUT
*Composite out doesn’t provide OSD or menu GUI on screen.
It is recommened to use composite out just for check video.
1 x VGA OUT
1 x Composite out (BNC)
- 14 -
2.4. Connecting Optional device
You can connect and control the PTZ device supporting RS-485 communication.
2.5. Connecting Network
Connect LAN cable (RJ45) to Ethernet port on rear of the product.
LAN cable (RJ45)
2.6. Connecting power supply
Connect provided power cable to AC-DC adaptor.
Connect the adaptor to DC power port on rear of the product.
Connect AC power plug to the plug socket.
- 15 -
3.Controlling DVR
3.1. Remote control – Basic description
3
4
6
1
2
8
5
9
7
1) REC : Instant record button
2) DVR ID
3) Number button : Input channel number
4) AUDIO : Audio ON / Mute
5) BACKUP : Access directly to backup menu
6) MENU : Access to main menu
7) OSD : Show or Hide OSD
8) PTZ : Control Pan/T ilt/Zoom camera.
9) Z/F: Access to digital zoom mode
10) Direction (▲,▼,◀,▶) & ENTER
11) SEARCH : Search recorded video
12) LOG : Show running status of DVR system
10
13) ◀◀ : Reverse play
11
13
17
21
14
18
22
15
19
23
12
16
20
24
14) ▶I : Play or Pause during playback
15) ▶▶ : Fast forward play
16) ■ : Stop playback and go to Live mode
17) SPOT : Not Operated in this model
18) PIP : Go to PIP mode
19) POP : Enlarge specific channel in Live mode
20) SEQ : Show each camera rotation
21) Full screen mode
22) Quad screen mode
23) 9 Division screen mode
Operated only for 8ch or 16 channels
24) 16 Division screen mode
Operated only for 16 channels
- 16 -
3.2. Remote control – Additional descriptions
3.2.1. Full screen mode
- Press button. Whenever pressing button, screen will go to next screen.
- Press desired numeric button of remote controller.
3.2.2. Quad screen mode
- To see quad screen mode, press button.
3.2.3. OSD Hide or Show
- Press OSD button of remote controller to appear or disappear OSD.
3.2.4. Sequence mode
- If you press SEQ button in Full screen split, screen will rotate automatically.
- Default value of cannel rotating interval is 2 or 3 seconds.
- User can select changing interval value from 1 to 99 seconds.
- User can select desired channel to display
- 17 -
3.2.5. Digital-ZOOM
DVR supports up to 10 times (x10) digital zoom
Select ZOOM icon or ZOOM button on remote control
Using mouse, drag certain area to enlarge image
To disable to digital zoom mode, mouse right-click
Normal mode Digital zoom mode x10
3.3. MOUSE
System supports USB MOUSE
Just Insert USB mouse into the product, then DVR will detect it automatically.
Inquire your supplier if certain USB mouse doesn’t work properly.
3.3.1. Change screen mode
Mouse left-click is for selecting an item on menu. Right-click in live goes to main menu.
Double left-click on a specific channel, screen will change into full screen mode.
With double-click in full screen mode, screen will go back to previous mode.
- 18 -
4. Operation
- 19 -
PLEASE MAKE SURE THAT THE HDD MUST BE INSTALLED AT FIRST FOR RECORDING BEFORE USING DVR.
4.1. Turning on
Connect Power Adaptor provided with the product into power DC terminal.
4.2. Initial screen
Log-in window will pop up after booting is over.
Please move the pointer into password window with mouse or up/down key of remote controller, and then
press enter button in remote control or right button of mouse.
If you first start DVR, input Initial password is “0000” (4 zeros). After first login, it is recommended that you
change password. In order to change password, please refer to page 38, USER.
4.3. Screen Layout
You can see the below items according to your selection on function.
- 20 -
backup with external USB
Instant Playback (10sec, 30sec, 1min,
4.3.1. Icons in Live Display Mode
In Live display mode, icons will be indicated to notify the system mode or status.
Below are the icon categories, which are indicated on the monitor.
Icon for system Icon for each channel
Selects specific 1ch with full screen
Screen-Division mode
Start/stop Panic(manual) record
HDD capacity usage status
When USB memory stick & HDD is
inserted into DVR
When DVR is connected via network
When DVR is not connected via network
System ID for remote control
Check auto-
HDD (status, capacity)
When Motion Detected
When Sensor Activated
Channel with audio connected
When PTZ mode entered
When channel is recording
When panic record is activated
3min, 5min, 10min ago)
Channel sequence mode
Digital x10 Zoom
Icon in full screen mode
- 21 -
ton in playback. Select this button to 1ch full screen
During playback, click this button and starting time is saved for
4.3.2. Controlling playback using the buttons
In search mode, the status will be shown in the upper side of screen. You can control playback using the
buttons.
This icon shows the current status in playback.
Current status
Backward
Play Play button. Select this button in pause mode
Pause Pause button. Select this button in play, rewind or FF mode.
Fast Forward
Stop
Search menu Selecting this button, the Search sub-menu will pop up
Digital zoom
If you select ▶, the mark will be ▶,
The mark will be changed if you select another button
Ex) If you select FF (fast-forward), ▶▶ will be shown.
Select backward and control speed (x2, x4, x8, x32 and x128)
In pause status, this button moves frame by frame reversely
Select fast-forward and control the speed (x2, x4, x8, x32 and x128)
In pause status, this button moves frame by frame forward.
Stop the playback and go to Live mode
Menu button also stop playing.
Digital zoom but
mode
Play speed Indicates speed of rewind or fast-forward
Backup Access to backup function
Bookmark start
Bookmark stop Click this button and bookmark ending time is saved for bookmark list
bookmark list
- 22 -
5. MENU
5.1. Access to menu
Press MENU button on front keys/remote control or right-click using mouse.
Before access to main menu, DVR asks you login ID and password.
When you first start DVR, input ADMIN for ID and 0000 for password as Initial ID & password are ADMIN &
0000 respectively.
5.2. SETUP
*Sub menus of SETUP
DISPLAY RECORD
CAMERA
OSD
SEQ-FULL
SEQ-QUAD
(Only 8ch support)
GENERAL
PTZ
PRESET
TOUR
PARAMETER
SCHEDULE
GENERAL
EVENT
MOTION
SENSOR
VLOSS
E-MAIL
FTP
E-MAIL SCHEDULE
ALARM SCHEDULE
FTP SCHEDULE
MISC
STORAGE
HDD FORMAT
HDD SMART
AUTO-BACKUP
NETWORK
SET UP
STREAM
DDNS
MOBILE
SYSTEM
CONFIG
TIME
INPUT DEVICE
USER
UPGRADE
TURN OFF DVR
- 23 -
5.2.1. DISPLAY
Configurations related to OSD can be made in OSD menu.
Sequence patterns of main and spot monitors can be programmed in LIVE-SEQ menu.
5.2.1.1. OSD
Select OSD items that displays on monitor and select language.
CAMERA NAME - Show camera name on screen.
CAMERA NUMBER – Show each camera numbers on
the screen.
CAMERA BOARDER – Show outline of channel.
LANGUAGE – Select OSD language.
OSD HIDE – Option: ALL, time bar or icon
AUTO HIDE – Hide ALL, time bar or icon automatically
after time-out (minute)
TIME OUT – AUTO HIDE after selected time (minute)
5.2.1.2. SEQ-FULL
LIVE SEQUENCE: Set order of sequence channel and
dwell time by second for main video out.
DEFAULT: Go back to initial value
ALL TIME: Apply same time for all channels
Maximum time is 99 second
- 24 -
5.2.1.3. SEQ-QUAD (Only for 8ch DVR)
SEQ: DVR supports 2 sets of quad split sequence.
SEQ 1 is CH1~CH4 and SEQ is CH5~CH8.
Sequence time can be set by second and maximum
time is 99 second.
5.2. 2. CAMERA
General camera configurations such as camera name, color and covert can be made.
Private zone on certain cameras can be designated.
PTZ configurations can be made.
5.2.2.1. GENERAL
NAME: Input name of each camera using virtual
keyboard. Maximum 15 digits in English can be used.
COVERT: Show or hide camera image in live mode
ON: Hide camera, OFF: show camera
AUDIO: Select connected audio channel
- 25 -
This information can be found in manual of PTZ
5.2.2.2. PTZ
How to input letters or numbers on TEXT INPUT box
Move the pointer to the name box (Blank) and click.
Click letters or numbers with direction button.
Click OK button after you complete input.
ID: Input ID of connected PTZ camera
PROTOCOL: Select protocol type of PTZ camera
BAUD: Select baud rate of PTZ camera
5.2.2.3. PRESET
① Select camera.
② Select “SET” button.
③ PTZ control screen of the camera will appear.
④ Move pan, tilt, zoom in/out to desired point.
camera.
CAMERA: Select camera to set up preset position
PAGE: Go to next page
CLEAR ALL: Cancel all saved presets.
⑤ Click Advance icon or Press ENTER Key in remote controller to save.
⑥ Click any other position on screen by mouse or press MENU Key to cancel.
If you like to cancel the setting, please click the CLE icon of the channel will be cleared.
If you click “CLEAR ALL” button, all value of channels will be cleared.
- 26 -
NOTE: Before using this function, please make sure that camera supports preset.
Total 64 preset points can be saved to each channel.
You can enter position name to each saved preset position.
5.2.2.4. TOUR
CAMERA: Select camera to set up scan point
LIST: Create another SCAN list
PRESET: Select desired preset potion
CLEAR ALL: Cancel all saved scan points
NOTE
In TOUR menu, you can set up PTZ tour route(SCAN-LIST) using saved PRESET position.
You can create 4 scan lists for each camera. You should setup PTZ protocol and PRESET before setting Scan-List.
Maximum 4 SCAN lists can be set and 1 SCAN list can be composed of up to 16 preset points
Example
If TOUR is set as left,
CAMERA 1 will move to saved positions as below,
PTZ04 (stays for 3sec) >> PTZ12 (stays for 3sec) >>
PTZ04 (stays for 3 sec) >> PTZ12 (stays for 3 sec) >>
PTZ04 (stays for 3 sec) >>……
5.2.3. RECORD
Recording setup such as parameter, schedule and pre/post recording can be made in RECORD menu.
- 27 -
5.2.3.1. PARAMETER
Recording resolution
CAMERA INPUT RESOLUTION
720P 1280 X 720
1080P 1920 X 1080
Resolution
-Recording resolution is determined automatically by HD SDI camera input and cannot be changed.
EVENT
- Select the recording picture quality and frame rate for EVENT occasions.
- Event occasions mean when motion is detected or alarm is triggered.
- Each channel can have separate picture quality and frame rate.
CONTINUOUS
- Select the recording picture quality and frame rate for continuous recording.
- Each channel can have separate picture quality and frame rate
- The frame rate in CONTINOUS cannot exceed that of Event mode.
If the frame rate of EVENT is set up as 8, and that of CONTINUOUS mode cannot exceed 8.
ALL
Apply the same picture quality & frame rate for all channels.
NOTE: When connecting 720P camera, please make sure you turn off DVR and hook camera cable to DVR
Otherwise, the unit will not recognize 1280x720 resolution and cause recording problem.
NOTE: The higher recording quality, the more HDD drive space needed.
Record Quality Picture Quality Disk Space Need
BASIC Low Least
NORMAL Fair Medium
5.2.3.2. SCHEDULE
DVR always records according to schedule.
Please make sure to set recording schedule during installation
HIGH Good Big
BEST Excellent Most
- 28 -
REC OFF: No record, just monitor during selected hours.
CONTINUOUS REC: DVR records continuously during selected days and hours.
EVENT REC: DVR records only when Motion/Sensor/Video Loss is triggered during selected hours.
CONTINUOUS + EVENT REC: DVR records continuously or by events during selected days and hours.
If there is no event, it will record video as continuous mode and
If there is event, it will record video as event mode as you set.
If you use mouse, you can select them by drag function.
NOTE: Recording schedule can be set by hour.
The time in the first column of each line means 00:00 ~00:59.
5.2.3.3. General
OVERWRITE: When HDD gets full, the oldest record
data will be erased and replaced (overwritten) by
new data.
ON: Use OVERWRITE, OFF: Not use OVERWRITE
If it is set OFF, DVR stops recording when HDD gets
full.
AUTO-DELETE: HDD only keeps the data of selected
PRE-REC TIME: Recording time before events (0~5 sec)
POST-REC TIME: Recording time after events (0~120 sec)
WATER-MARK: Generate water-mark in recording data Authenticity can be verified in
backup-viewer software.
- 29 -
when motion is detected.
5.2.4. EVENT
Configurations regarding events can be made.
5.2. 4.1. MOTION
CAMERA: Select camera for motion setup
SENSITIVITY: Adjust motion sensitivity from 0~9
The higher number, the more sensitive detection
ALARM-OUT: Check alarm-out 1 if you wish to
trigger alarm out 1 when motion is detected.
RECORD CH: Select channels which will record
BUZZER: Set ON/OFF for buzzer when motion is
detected
NIGHT MODE: Set separate sensitivity for day and
for night. This option can be used in order to avoid
false motion event caused by camera noise at night.
SET ALL: All area (8x8 Grid) will be enabled for
motion detection.
CLEAR ALL: All area (8x8 Grid) will be disabled for
motion detection.
- 30 -
Select camera channels which will
5.2.4.2. SENSOR
TYPE: Select NO(Normal open)/NC(Normal close)
RECORD:
record when sensor is activated.
ALARM-OUT: Check alarm-out 1 if you wish to
5.2.4.3. VLOSS
5.2.4.4. E-MAIL
DVR can send e-mail notification when events occur.
trigger alarm out 1 when sensor is activated.
BUZZER: Set ON/OFF for buzzer when sensor is
activated.
ALARM-OUT: Check alarm-out 1 if you wish to
trigger alarm out when video loss occurs.
BUZZER: Set ON/OFF for buzzer when video loss
occurs.
ALL: Apply the same settings to all channels.
EVENT E-MAIL: Select ALL time or SCHEDULE for
email notification
IMAGE: Check the box then DVR sends image as
well as text when events occur.
EVENT TYPE: Select event type from MOTION,
POWER ON, SENSOR, HDD ERROR, VLOSS
SENDER ID: DVR sends email with this name
E-MAIL ADDRESS: Input up to 2 email addresses.
Example: anyone@gmail.com
SECURE TYPE
-NORMAL: Standard email transfer, Port 21
-SSL(465): Secure email transfer, Port 465
-TLS(587): Secure email transfer, Port 587
SERVER NAME: In case of using SSL or TLS, input
SMTP server name
ID/PASSWORD: In case of using SSL or TLS, input
ID and password of SMTP server
- 31 -
NOTE: You can find SMTP server information usually from POP3/SMTP, IMAP/SMTP setup menu of the server.
Otherwise, you need to ask the server manager.
EXAMPLE:
your Gmail account. If normal is selected, you don’t need to input in SERVER NAME and ID/PASSWORD.
EXAMPLE: Email message
From : DVR@dvr.com
To : anyone@gmail.com
Sent: Friday, July 24, 2011 6:11 PM
Subject: EVENT MESSAGE
If you have an account in Gmail, Input smtp.gmail.com in SERVER NAME and ID/PASSWORD of
[2011/07/24 18:10:11] [testdvr/192.168.001.121] MOTION ch 1 ON
5.2.4.5. FTP
DVR can send text + image to designated FTP server when events occur.
FTP: Select OFF, TEXT or TEXT + IMAGE
EVENT TYPE: Select event type to send to FTP.
FTP address: Input IP address or domain name of
FTP server.
Account ID: Input ID to access FTP server
Account PW: Input password to access FTP server
Directory Name: Directory of FTP server that will
save transferred text or image
PORT: Input port number to use transfer to FTP
FTP normal uses port 21.
5.2.4.6. E-MAIL/ALARM/FTP SCHEDULE
Make a schedule for e-mail transfer, alarm-out and ftp transfer for events.
Schedule can be arranged by day and by hour. Only during checked day and time, e-mail will be sent and
alarm-out will be activated and ftp transfer will work.
- 32 -
E-Mail schedule:
Select day & hour (Mouse drag/drop)
Alarm-out schedule:
Select day & hour (Mouse drag/drop)
FTP schedule:
Select day & hour (Mouse drag/drop)
5.2.4.7. MISC
DWELL TIME: Dwelling time for alarm-out
Maximum 9999 seconds.
ALARM OUT: Select N/C or N/O.
To deactivate, click ALARM OUT
EVENT POPUP: Channel where event occurs pops
Note: if event occurs during dwell time of another event, dwell time will be ignored and newer event will pop up
up in full screen mode.
POPUP OUT : Only support NORMAL (Main video
out: VGA and HDMI)
POPUP SEQUENCE TIME: Popup dwelling time
- 33 -
When format is completed, DVR will reboot
5.2.5. STORAGE
1 internal hard drives can be installed in the unit. Additionally 1 E-SATA hard drive can be attached to the
unit using E-SATA port in the rear.
5.2.5.1. HDD FORMAT
HDD must be formatted when installed in order to record properly.
New HDD must be formatted before using it with DVR
automatically.
Time to format can be different depending on size of
HDD but it usually takes a few minutes to complete.
SHOW: indicates file list of HDD
E-SATA information is always indicated after internal
hard drive(s).
5.2.5.2. HDD SMART
Temperature of HDD can be checked.
If the temperature gets higher than certain point, DVR can notify user of that.
- 34 -
Select ON in SMART
TEMPERATURE THRESHOLD
Set the limit temperature of HDD
INSPECTION CYCLE
Set the interval to check HDD temperature
5.2.5.3. AUTO-BACKUP
Options: Every 10 minutes, Hourly and Daily
DAILY TIME
In case you select “Daily” in inspection cycle, set
time to check HDD temperature during a day.
ALARM OUT
Select alarm out ports which will activate when
HDD temperature exceeds over set temperature
threshold.
BUZZER: Select ON/OFF of buzzer sound when
HDD temperature exceeds over set temperature
threshold.
TYPE
Once USB HDD is connected to DVR, HDD status is
indicated. Recording file list can be checked by
selecting SHOW.
EXTEND: When internal HDD(s)(including E-SATA
HDD) gets full, HDD starts to overwrite and eldest
data will be erased from internal HDD and saved in
USB HDD at the same time.
MIRROR: Same data of internal HDD will be
recorded in USB HDD
INTERNAL HDD: To use this function, internal HDD
and E-SATA must be installed. Internal HDD and E-
SATA will have the same data as RAID 1.
- 35 -
DVR automatically gets IP address, gateway
Check port forwarding for
5.2.6. NETWORK
5.2.6.1. SETUP
TYPE: Select network type among STATIC, DHCP and
ADSL(PPPOE)
DHCP:
and subnet mask.
STATIC : Check your network environment and input
IP address, gateway and subnet mask manually.
ADSL: Input PPPOE ID and PASSWORD.
MOBILE PORT: Port that is used for jpeg transfer
Smart phone application uses this port.
CLIENT PORT: Port that CMS uses.
WEB-PORT: Port that web viewer uses.
All the ports numbers can be input from 0001~9999.
Each port must not have identical port numbers.
BANDWIDTH: Control up to unlimited bandwidth
AUTO port forwarding:
network connection from outer network.
Router itself should support UPNP function
- 36 -
is ok, STATUS shows
5.2.6.2. STREAM
When dual stream is activated, DVR sends separate network stream of resolution, picture quality and frame
rate. When dual streaming is set OFF, DVR should send stream according to resolution, picture quality and
frame rate set in recording parameter.
According to HD SDI video input resolution (1080P or 720P), 1080P supports 960*540 & 480*270 for
network resolution and 720P supports 640*360 & 320*180 for network resolution.
Resolution Normal Frame
960*540
480*270
640*360
320*180
Basic
Normal
High
Best
1, 2,
4, 8,
15, 30
5.2.6.3. DDNS
DVR supports DDNSCCTV.COM, DDNSCCTV(AUTO), DYNDNS.COM and NO-I P. CO M for DDNS connection.
Using DDNSCCTV.COM(AUTO)
If you choose DDNSCCTV.COM(AUTO) in SERVER, DVR creates HOST NAME using DVR using MAC
address of DVR.
1) Click DDNSCCTV.COM(AUTO) in SERVER
2) Then USER ID, PASSWORD and HOST NAME are generated automatically using MAC address.
3) USER ID, PASSWORD and HOST NAME are formed in DVR + last 6 letters of MAC address
EX) If MAC address of DVR is 00:0E:B5:02:8A:5F, USER ID & PASSWORD are dvr028a5f and HOST
NAME is dvr028a5f.ddnscctv.com
Using DDNCCTV.COM, DYNDNS.COM or NO-IP. C OM
SERVER: Select DDNS server
USER ID: Input DDNS server account ID
PASSWORD: Input DDNS server account password
HOST NAME: Input domain(host) name that you
made at DDNS server
CONNECT: Click the button to check connection to
DDNS server. If connection
DDNS OK
- 37 -
PC to use DDNS service before you make
Domain name can be created with
combinations of alphabets, numbers and
(You must not put a mark on first letter of
NOTE: To use DDNS function, you must first go to www.ddnscctv.com, www.dyndns.com or
www.no-ip.com
NOTE: If DDNS connection fails, check if all information has been input correctly (especially USER ID and
PASSWORD) and check network status.
on PC and create an account and make a domain (host) name.
How to register DDNSCCTV
Input http://ddnscctv.com on web browser of
configuration on DVR
Click Registration button if you don’t have an
account.
Fill in E-mail address, password, name and etc.
Then, click Submit button
Input domain name you wish to create and
click Request Domain button.
marks.
domain name.)
Click Logout button after domain name has
been successfully registered.
You can sign in with E-mail and password you
registered.
- 38 -
DDNS setup on DVR
① Move to SETUP NETWORK DDNS
② Select DDNSCCTV.COM (3 options : DDNSCCTV.COM, NO-IP.COM, DYNDNS.COM)
③ Input E-mail address & password you registered at http://ddnscctv.com
④ Input domain name you registered at http://ddnscctv.com
on HOSTNAME.
on USER ID and PASSWORD.
DDNS use
Input domain name you registered on web browser.
Example: http://abc.ddnscctv.com
For WAN connection, DVR web port/client port should be forwarded. (Port-forwarding)
In this case, input : (colon) web port.
Example: If web port is set 1000 on DVR, http://abc.ddnscctv.com:1000
5.2.6.4. MOBILE
When connecting to DVR remotely from mobile devices, DVR sends out JPEG stream.
Resolution & frame rate of JPEG stream can be set up. Resolution options are 960 x 540 and 480 x 270 in
case of 1080P camera. For 720P camera, resolutions of 640 x 360 and 320 x 180 are available.
* JPEG stream frame rate by resolution
Resolution
960x540
(640x360)
480x270
(320x180)
Maximum frame rate that can be set by resolution is as the table above. For 960x540(or 640x360), total fps
is 15fps from channel 1 to channel 4. The same 15fps also applied from channel 5 to channel 8.
Ch1 ~Ch4 Max. 15fps in total Max. 30fps in total
Ch5 ~Ch8 Max. 15fps in total Max. 30fps in total
- 39 -
5.2.7. SYSTEM
Configurations for time, user and etc. can be made.
Software version can be checked and upgrade process can be made.
5.2.7.1. CONFIG
System setting values from one DVR can be copied to others.
Insert USB device into USB port of DVR to import (load) or export (save) the setting values.
CONFIG IMPORT & CONFIG EXPORT can be used to make several DVRs to have the same setting values.
CONFIG IMPORT: Load the saved configuration
file from USB device
CONFIG EXPORT: Save the configuration file to
USB device to copy it to another DVR
DEFAULT: Change all configuration values back
to factory default.
5.2.7.2. TIME
DATE FORMAT: Select date format
YY/MM/DD MM/DD/YY DD/MM/YY
TIME FORMAT: 24HOURS or AM/PM
TIME ZONE: Select time zone of your location
TIME SYNC: System time will be synchronized
with selected time server if it is turned ON.
- 40 -
5.2.7.3. INPUT DEVICE
SERVER IP: Input IP or domain name of time
server.
Click TEST if connection with time server is OK.
DVR checks time server for correct time every 1
hour.
Example: time.bora.net (OK),
http://time.bora.net
(NOT OK)
CHANGE TIME: Change time manually
SYSTEM-ID: Input the number that you want to
register in this DVR.
KEYBOARD: DVR system can be connected with
control keyboard.
KEY-TONE: Beep whenever button is pressed if
ON is selected.
How to set up System-ID status
System-ID status shows whether the system will accept key from remote-control or not.
SYSTEM-ID is used when user operates several systems with one remote control.
SYSTEM- ID will be displayed when SYSTEM- ID is other than 0(zero).
By using DVR-ID button of remote control, remote control can be matched with SYSTEM- ID, or if
SYSTEM- ID is 00, system-ID is not displayed and system accept key from remote controller.
If SYSTEM- ID color is Yellow, the system accepts remote-control key input.
If SYSTEM- ID and Active-ID are not matching, SYSTEM- ID color will be Red and the system does not
accept remote-controller key input.(No beep)
How to match SYSTEM- ID by remote controller
(1) Press DVR-ID button of remote controller.(You can hear short double-beep.)
(2) Then, press desired System-ID by using 2 numeric button. (E.g. 02 or 03 or 01)
- 41 -
R : 01
R : 02
R : 03
Not working
Active ID : 02
Work ing
Not working
5.2.7.4. USER
There are 2 fixed users, ADMIN & NETUSER. Their name & access authority cannot be changed. Additionally,
you can create up to 20 more users and give different access authority level to each user.
USER – There are two unchangeable user IDs (ADMIN, NETUSER), to create new user or modify
settings of existing users, click arrow button.
PASSWORD – Initial password for each user is set ‘0000’. When you create a new user, make sure
that you have to enter new password and do not forget the newly input password. Up to 8 digits of
numbers can be used for password (EX: 123456)
SETUP – Check this box then the user is authorized to go into setup menu
DVR FUNCTION– Click DVR function button of REC (Recording setup), PLAY (SEARCH), BACKUP and
PTZ (Control) to give each user access authority.
NETWORK – Check this box then the user is authorized to access to DVR via network (Web, CMS or
mobile)
COVERT CH – Select covert channels by each user. Marked channels will be hidden by the user
TIME OUT – When this is set to ON, LOGIN window will re-appear after entered time from any
signal input. If you want to log out, you need to go to MENU and select LOG OUT like right picture.
MONITOR – First select ON to give monitoring authority to each user. Then click CH button to
Select monitoring channel the user can access.
- 42 -
5.2.7.5. UPGRADE
You can check version information of software and firmware upgrade can be done.
USB upgrade: Upgrade using USB device
Network upgrade: Upgrade via network
USB UPGRADE
Please select USB upgrade in upgrade window
① Copy provided firmware file to your USB memory stick
② Insert USB Memory which includes Firmware into USB Port.
③ Enter UPGRADE button to upgrade firmware, then small windows will appear.
④ Please click OK Icon and the message dialogue to confirm will popup,
⑤ And please click OK, or CANCEL to proceed.
⑥ It will take some minutes to upgrade, and then DVR will be rebooted automatically after upgrade is
finished.
Network upgrade
Please select network upgrade in upgrade window
① Check out whether Server IP and FILE NAME are correct.
If shown information is wrong, correct SERVER IP and FILE NAME and press ENTER button to input
new information by text input Dialog box.
NOTE : Make sure the information of Server IP & File name through your supplier.
② Select OK and press ENTER button to start S/W upgrade.
After completing upgrade, the system will reboot automatically.
- 43 -
5.2.7.6. TURN OFF DVR
Select TURN OFF DVR and software of DVR will be shutdown.
In order to completely shut down DVR, turn off the power switch in the rear.
5.3. SEARCH
Time search using calendar/time bar and event search using event logs are supported.
- 44 -
5.3.1. SEARCH BY TIME
Select date on calendar
Select hour & minute on time bar
Data on minutes is displayed by ALL and each channel
Click “PREVIEW” button after selecting minute and
channel no. on then playback of that channel starts
on the small window.
Click “PLAY” while running preview and it enlarges
into full screen.
To watch playback without preview, just click “PLAY”
after selecting minute.
NOTE:
Dates with recording data are indicated in yellow. Hour/minute with recording data are indicated in bright blue
GOTO FIRST/ GOTO LAST: Playback of earliest data/
latest data.
5.3.2. SEARCH BY EVENT
Select DATE & TIME to get event logs
Select CH to get event logs
5.3.3. THUMBNAIL SEARCH
Thumbnail search is effective and quick search option. You can search recorded file of certain channel by
displaying 9 screens at a time by selected time interval.
Select EVENT TYPE to get event logs
Select SEARCH button and event log list will be
written.
<PGUP, >PGDN: Page up & down of list
<<FIRST, >>LAST: Go to first page or last page of list
Click an event log on list then DVR goes to the time
when the event happens in search mode.
- 45 -
format and backup viewer program will be
CH: Select channel number to view.
TIME: Select time to start “Thumbnail search”
INTERVAL: Select time interval from 1 sec, 10sec to 1
minute & 1 hour.
VIEW: Capture image by selected interval starting
from selected time shows up
If 1 hour is selected, each screen shows by 1 hour of
the same channel.
NEXT, PREVIOUS: Previous or next page of recorded
file by selected interval
Seeing the capture image, double-click on certain screen then it will be divided in smaller interval.
If you set 10:00AM in TIME and 1 hour in INTERVAL then first screen shows 10:00AM and second 11:00AM.
Double-click on second channel and it will be divided again in 9 screens by 10 minute (1 minute, 10 seconds
and 1 second) starting from 11:00AM.
5.3.4. BACKUP
Recorded data can be archived in USB device or CD/DVD using backup function
First, insert USB device or CD/DVD and select backup menu from main menu or press backup button on
remote control and below popup will show up.
DEVICE: Select device for backup
CHANNEL: Select channel(s) to archive
To AVI : Data will be archived in AVI format
If unchecked “To AVI ”, data will be archived in PS
automatically copied.
TIME STAMP: Insert time stamp into AVI file
FROM/TO: Input starting time & ending time
Without having to input time directly, 1 minute ~ 60
minutes of backup can easily be made.
BOOKMARK: Go to bookmark list that have been
made in playback mode.
- 46 -
*Bookmark Backup
You are able to make a backup file bookmarked in playback mode by clicking “Backup icon” or delete from
the list.
5.3.5. SEARCH MODE
When DVR is in search mode, you can play, pause, rewind & fast-forward (x2, x4, x8, x32 and x128)
If you move mouse cursor at the bottom of screen, time bar pops up and you can drag and move the time
in the bar. Time bar contains 24 hours and time of recording data is indicated in brighter blue. By bookmark
icon you can select starting and ending time of backup file here.
For more detailed description of icons, please refer to page 20, 4.3.2. Controlling playback using the
buttons
- 47 -
5.4. Other functions
5.4.1. PTZ
When you press button of remote control or select PTZ in main menu, screen will be changed
to FULL screen mode and you can control PTZ camera.
Select another channel on the PTZ control menu or press numeric button of remote control then
target camera will be changed.
Press ◀▶▲▼ button and camera will pan to left / right or tilt up / down.
Press ◀◀ / ▶▶ button or search / log button of remote control or click (+), (-) button and
camera will zoom in or out.
FOCUS
+ : Focus-IN.
P/T
- : Focus-OUT
AUTO : AUTO-FOCUS mode.
IRIS
+ : Open Iris.
- : Close Iris.
IRIS : AUTO-IRIS mode.
SPEED
+ : The control speed will increase.
- : The control speed will decrease.
PRESET
If you want to go to a specific PRESET-position, select “GO” button.
If you want to scan PRESET-positions, select “TOUR” button
AUTO SCAN
Input the auto scan number and click “AUTO SCAN” button
PATTERN
Input the pattern number and click “PATTERN” button
OSD MENU and direction keys
Click “OSD MENU” button and you will go into camera OSD menu. With the direction keys below, you
can move and select settings in camera OSD menu.
- 48 -
Before using this function, make sure audio in/out
NOTE: OSD Control function supports only for “PELCO-D” protocol
5.4.2. Audio
device has been installed correctly.
Audio out works only in 1CH full screen mode
Test audio by TEST ON/OFF button
5.4.3. Log view
System log status can be found or saved into USB memory to check on PC.
EVENT TYPE: Select event type to see logs.
FROM: Input staring time
TO : Input ending time
BACKUP: Save log data into USB memory
SEARCH: Click SEARCH button and log list will be shown
EVENT LIST: Logs of checked EVENT TYPE will be listed.
- 49 -
5.5. OSD OFF
Select OSD OFF then OSD (icons or time) will disappear/appear.
Please see the page 22 to get more information. [SETUP->DISPLAY->OSD]
5.6. REC
Select REC button on main menu, on remote control or on front panel. Then, all channels will record
regardless of previous recording schedule setup. This function can be used when unexpected incident
occurs in channels that are not recording by operator meaning panic or instant recording. One more
REC makes DVR go back to the previous recording schedule setup.
Example: While only channel 2,3 and 4 are recording by the current recording schedule,
unexpected incident is happening on channel 1 so channel 1 needs to be recorded.
In this case, select REC function instantly on remote control or on front key. Then all channels will
be recorded.
5.7. LOG OUT
Select LOG OUT button and DVR will go in logged out status.
You cannot control DVR and change settings of DVR in logged out status. In order to log in again, press
any button of remote control or front key or click mouse button on any spot of screen.
NOTE: When DVR goes in logged out status, all channel might be blocked by covert according to settings
in page 39. (If USER >> MONITOR is on, all channel will be blocked by black screen in logged out status.)
- 50 -
Specification
MODEL HD SDI 4CH DVR HD SDI 8CH DVR
Compression Algorithm Video : H.264, Audio : G726
Operating System Embedded Linux
Multi-Operation Pentaplex (Live, Recording, Playback, Backup, Network)
Video
Video Out
Audio
Interface
Live
Recording
Input 4CH 8CH
Input Signal HD SDI
HDMI 1
VGA 1
Composite 1
Input 1
Output 1 (HDMI, RCA)
USB 2.0, RS-485 2 x USB, 1 x RS-485
E-SATA 1
Ethernet 1
Sensor Input 1
Alarm Output 1 (Relay)
SATA 1 x SATA HDD (Up to 3TB)
Resolution 1920 x 1080
Display Mode 1, 4 1, 4, 9
Digital Zoom Up to x 10
Speed & Resolution Total 60FPS(50FPS) @ 1080P or 120FPS(100FPS) @ 720P
Mode Manual / Continuous / Schedule / Motion / Sensor & Pre/Post, Panic
Speed Fast Forward/Backward, Step Forward/Backward
Playback &
Backup
Events & Alarm
Network
Operating Temperature and Humidity
Power and Dimension (WxDxH) DC12V, 3.3A and 380 x 342 x 67, Packing: 450 x 425 x 170 (mm)
Search Search by Time, Calendar , Events and Thumbnail search
Backup Device USB Memory Stick/HDD & Backup by Network
Backup File Format AVI (With or Without Timestamp), PS (Playback in Backup-Viewer)
Transmission
C.M.S 6 Monitors, Live , Event Manager, E-Map, Playback, Backup , PTZ, DVR Setup
Web (I.E) Live Monitoring, Playback, Snapshot and PTZ Control
Email & FTP Notification / Alarm-out / Buzzer for Events & Video Loss
Warning Message & Buzzer for HDD Over-Temperature
Video Dual-Stream (Local recording & Network Transmission)
Bandwidth adjustable (64/128/256/512Kbps, 1/2/4/10Mbps, Unlimited)
5~40 ℃ / 20~80% RH
- 51 -
Trouble shooting
In the event of a product malfunction, please check the following list for a usual and possible solution
before requesting service.
1. Product is not turned on.
Check out whether the power is being supplied well.
2. Product continues displaying “Loading” or “Starting UI….”
Check the product can boot without HDD
If product continues displaying “Loading” or “Starting UI….” Without HDD, you can try emergent upgrade.
Please refer method of factory default in provided CD
3. Camera video is not displayed on monitor
Check the video input / output connections on the product rear panel.
Check the camera status and the connection between camera video/power cable.
Check if CAMERA STATUS in menu is SHOW.
4. I cannot hear Audio
Check the audio input/output connections on the rear panel of DVR.
Audio works only in full screen mode.
5. I can’t stop recording by remote controller or REC button
Check out that RECORD CONTINUOUS of REC OPTION of MENU is OFF.
6. I can’t find previous recording data.
The product operates automatically OVERWRITE function. It deletes the oldest recording data to overwrite
when HDD is full.
7. Product is not compatible with external USB device.
Please check if USB memory stick is in protection (password) function. Protection function of USB device
should not be discharged.
8. I can’t connect to network.
Check if network of menu is setting correctly such as Network port, ID, Password
Check if your internet line is available. Please ask your service provider to check internet line.
If the problem you are experiencing persists or is not mentioned above, please contact service center or your
local distributor.
- 52 -
Loading...