Syris SY210NT Series Quick User Manual
SYRIS SY210NT Series
Quick User Guide Manual
Ver : 2.00
Control up to 4 doors with in/out reader
Baud rate 2,400 - 115,200 bps
SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 1 -
SY210NT Serial Basic Menu Structure
We list SY210 basic menu structural drawing here for user to get familiar with the SY210
serial controller operation procedure. The first step is to execute the white box “ Login
procedure” to enter dark gray box “main menu” and light gray “sub-menu”, please refer
the diagram key and the direction of arrow, the function description of sub-menu will be
introduce at below document.
SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 2 -
Overview
Item Contents Page
01
Attention matter
3
02
Login/logout steps
3
03
Setup module (setup reader)
4
04
Add/delete/edit card
8
05
Add and delete fingerprint
12
06
Setup controller ID (when multiple
controllers online)
18
07
Procedure control (setup open door
button)
20
SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 3 -
01 Attention matter
Install:
When the user ready to install SY210 serial controller, please open the controller cover on
the back (TSN and SSN model) and confirm the white disconnect film has been removed.
When the user first time connect the power, all the lights flash and produce serial sound,
please proceed system replacement by click 1 key according to the controller LED display
(1：Clear)
Setup:
The controller and reader factory default ID all set to “1” Please setup ID first before
connect multiple controller or reader to avoid ID repeat cause communication failure.
Please refer the reader ID setup method of page 5 “Setup module”. And about controller ID
setup please refer page 17 “Setup controller ID”
02 Login/logout step
The SY210NT controller needs to complete the login step to enter function menu. The
controller will automatically logout when the user stops operating about two minutes.
However, in order to confirm the door access security, please execute logout steps after
finish setting.
Login Step
Enter key LCD display Reference
MENU System
EN Login
EN Password
Wait for password enter
1+2+3+4+EN Master OK
Setup light flashes, already in login status
SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 4 -
Logout Step(in login status)
Enter key LCD Display Reference
MENU System
EN Login
▼ Logout
EN Display date and time
Setup light goes out, complete logout
step.
＊ The below steps pre-set in login status
03 Setup Module (setup reader)
After install controller and reader, the user needs to setup reader ID and scan
communication status from controller (plug & play) to normal transmit the I/O data. The
next diagram is System main menu table and the gray part is the step operation range.
SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 5 -
Setup reader ID
Enter key LCD display Reference
MENU System
EN Login
▼＊５
System
Process
EN
APBLevel
Seting
▼＊２
Change
ModuleID
Modify/setup module ID item
EN
Module
[READER]
Use ▲▼ key to choose the installed
module type (annotate 1)
EN
Serial
03150001
Enter module serial number(annotate 2)
EN
ModuleID
ID = [ 1 ]
Setup module ID (annotate 3)
EN
Change
ModuleID
Setup complete, back to item
Annotation 1: Module type
Annotation 2: The user can find the serial number sticker from card reader package or
machine back.
Annotation 3: Card reader ID arrange rule
READER General proximity reader, including SYRDS1、S5、L5。
DIDO Digital contact expand module, including MDDIDO-1S、MDDIDO-16。
PRINT Printer module
SYRDK5 Keypad proximity reader
SYRDF5 Fingerprint proximity reader
SYRDT5 LCD display card reader
Door one Door two Door three Door four
Incoming reader ID 1 ID 2 ID 3 ID 4
Outgoing reader ID 5 ID 6 ID 7 ID 8
Door
Function
SY210NT Serial Controller Quick User Guide Manual
© 2004 by SYRIS Technology Corp.
- 6 -
Scan communication from controller (plug & play)
Enter key LCD display Reference
MENU System
EN Login
▼＊３
Module
Process
EN
ADD
Module
▼＊３
Module
PlugPlay
Scan module communication item
EN
Module
Waitting
Scanning communicated module
Please wait
Find：01
OK
Display communicated module
amount(annotate
)
CLR
Module
PlugPlay
Setup complete, back to item
Annotation:
The controllers will automatically display the plug & play result. In normal status, the display
module amount will match with the practical installed module amount. In another word, the
scan result should display: Find: 04 OK. If the display amount is unusual, please refer the
below table to eliminate the issue.
Unusual
situation
Scan (display 00) or display less amount
Possibility The communication is not correct or repeat ID
Eliminate
method
◎Please confirm the communication again
◎The factory default of reader ID all set to “1”. The ID did not setup
properly when communicated with multiple reader or ID repeat cause
transmission conflict and can not find the module correctly.
Please contact with the Syris technical personnel if confirm the above questions but still can
not communicate correctly.
Loading...