Synology E10M20-T1 User Manual

Synology Adapter Card E10M20-T1

Hardware Installation Guide

Table of Contents

Chapter 1: Before You Start

Package Contents 3
Hardware Specication 4
LED Indicator Table 5
Safety Instructions 6

Chapter 2: Hardware Setup

Tools and Parts for Installation 7
Attach M.2 SSD to E10M20-T1 Adapter Card 7

Synology_HIG_E10M20-T1_20200227

2

Chapter

Before You Start

Thank you for purchasing this Synology product! Before setting up your new adapter card, please check the
package contents to verify that you have received the items below. Also, make sure to read the safety instructions
carefully to avoid harming yourself or damaging your adapter card.

Note:

All images below are for illustrative purposes only, and may di󰀨er from the actual product.

Package Contents

Adapter card x 1 Heatsink x 1

Rubber x 4 (Bag #1)

1

Thermal pad x 9 (Bag #2)

Full-height bracket x 1 Screw pillar x 3 Screws x 6

3

3

Hardware Specication

Item E10M20-T1

Host Bus Interface PCIe 3.0 x 8

Bracket Height (mm) 80 (low prole), 120 (full height)

Size (H x W x D) (mm) 71.75 x 200.55 x 17.70

General

Agency Certication

Environment Requirement

Interface NVMe

• FCC Class B • CE Class B • BSMI Class B

• VCCI • RCM • RoHS Compliant

• Operating Temperature: 0°C to 40°C (32°F to 104°F)

• Storage Temperature: -20°C to 60°C (-5°F to 140°F)

• Relative Humidity: 5% to 95% RH

Storage

Network

Note:

The supported NVMe SSD will vary from di󰀨erent Synology NAS, please visit

Supported Form Factor M.2 22110/2280

Connector Type and Quantity M-key, 2 slots

• IEEE 802.3an 10GBASE-T 10 Gbps Ethernet

• IEEE 802.3bz NBASE-T 2.5 Gbps/5 Gbps Ethernet

IEEE Specication Compliance

Data Transfer Rates 10 Gbps/5 Gbps/2.5 Gbps/1 Gbps/100 Mbps

Network Operation Mode Full Duplex

Connector RJ45 Copper

Cable Distance 10GBASE-T: 55M using CAT 6, 100M using CAT 6a

• IEEE 802.3ab 1000BASE-T 1 Gbps Ethernet

• IEEE 802.3u 100BASE-Tx Fast Ethernet

information.

• IEEE 802.3x Flow Control

www.synology.com

to get more

LED Indicator Table

LED Indicator Color Status Description

Green Static 10 Gbps connection

LAN

(on upper side of jack)

LAN

(on lower side of jack)

Orange Static 5 Gbps/2.5 Gbps/1 Gbps/100 Mbps connection

O󰀨 No network

Static Network connected

Green

Blinking Network active

O󰀨 No network

Note:

Model specications are subject to change without notice. Please refer to

www.synology.com

for the latest information.

5 Chapter 1: Before You Start

Safety Instructions

Keep away from direct sunlight and from chemicals. Make sure the environment does not experience
abrupt changes in temperature or humidity.

Place the product right side up at all times.

Do not place near any liquids.

Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or
aerosol cleaners.

To prevent the unit from falling over, do not place on carts or any unstable surfaces.

The power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is
correct and stable.

To remove all electric current from the device, ensure that all power cords are disconnected from the
power source.

Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately.

6 Chapter 1: Before You Start