Synergy SL, PM2, SL/PM2 User Manual

Download

Page 1

M (8x) 300-505

Cup Point Set Screw

K (2x) 300-555

2” Button Head

R (2x) 301-422 Base Plate

F (8x) 300-485

Button Head Screw

L (2x) 300-470

Metal Washer

N (1x) 400-060 3/16” Hex Key

O (1x) 400-070 1/8” Hex Key

G (16x) 300-560

Flat Nut

P (2x) 301-425

Post Cover

R (4x) 300-468

Washer

Q (8x) 301-575

Plastic Fasteners

S (5x) 301-600

Wire Manage

BACK EDGE

NOTE:

If i nstalling mount to an assembled triple unit, remove the two rear center connector bolts. Replace with base plates (R).

A . Loosely assemble 2 flat nuts (G) with 2 button

head screws (F) through each base plate (R).

B. Secure the base plates (R) to the two rear center posts with

the 2” button head screws (K) and washers (L) Tig ht e n f ir m ly w ith hex k ey (J) .

A . Align thru holes in posts over the pins in the base plates.

Guide the flat nuts (G) through the front of the posts.

If necessary, use rubber mallet or other device to ensure the posts fits snugly against the top surface.

Tighten the screws (F) w ith hex key (H).

SYNERGY TRIPLE PANEL MOUNT

SL /PM2

BEFORE YOU BEGIN

• This TV mount is intended for use with Flat-Panel TV 60” or smaller and a maximum weight of 175lbs.

• Use with products heavier than the maximum weight or larger than the size indicated may result in instability causing possible injury.

• Carefully inspect the mount for shipping damage or missing parts. If any damage is apparent or you are missing parts contact Salamander Designs at 800-535-5659.

• Read ALL instructions before assembly. If you have any questions, please contact your installation contrator or Salamander Designs.

• Mounts must be attached as specified in assembly instructions. Improper installation can result in serious personal injury.

S (1x) 400-080 5/32” Hex Key

1. INSTALL BASE PLATES

2. INSTALL POSTS

Black

2 Extruded Posts

Fx 100/L Mount Kit

FX 100/L

Thru Holes

PARTS

SYNERGY TRIPLE MOUNT HARDWARE BAG -PHK-516

Page 2

Slide the post bracket into the posts as shown below, guiding the flat nuts (G) to ensure all parts slide freely.

Position the post bracket vertically along the posts where you w ish the center of the television to rest.

Tighten button head screw s (F) wit h hex key (H) to firmly

set the bracket onto the posts.

B. Assemble 8 flat nuts (G) with 8 set screws (M ) and

drop into the left and right sides of each post.

C. Position the set screws (M) into the thru holes and tighten

throughto the base plate pins. This will lock the posts to the top of your Synergy cabinet.

Tighten firmly w ith hex key (O).

Thru Holes

Salaman der Designs Ltd. w ww .salam anderdes igns.co m 800-535-5659

Squeeze to remove.

3. ATTACH TV BRACKETS TO TV

5. INSTALL POST BRACKET WIRE MANAGERS & CAPS

4. ASSEMBLE POST BRACKET

Refer to Step 2 of the Flexo 100/L Manual.

6. HANG TV

Assemble 1 Button Head Screw with Washer through the indicated slot (4 places) with flat nuts loosely on each.

Thread the screws loosely to the nuts just enough to ensure the nut does not fall off.

Center TV Brackets (II) on Wall Bracket (I) and push black Click Fasteners up into lock position.

Install Pad Lock (IV).

Pull on black cord to unlock Click Fasteners and hook TV Brackets (II) onto Wall Bracket (I) from top.

LIMITED WARRANTY- For five full years Salamander Designs Ltd. will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.