Page 1
S21315 / S21318 User Manual
ALLNET
GmbH
S21315/S21318
5/8 10/100/1000 Mbps
Ethernet Switch
Page 2
S21315 / S21318 User Manual
ALLNET
GmbH
Content
1. Introduction -------------------------------------------------------------- 3
1.1 Switch Features ---------------------------------------------- 4
1.2 Package Contents ------------------------------------------- 5
1.3 Front Panel and Rear Panel Specifications --------- 6
1.4 LED Indicator Specifications ---------------------------- 7
2. Installation --------------------------------------------------------------- 9
2.1 Before Connecting to the Network -------------------- 9
2.2 Connecting to End Nodes ------------------------------- 10
2.3 Switch to Router or Switch ------------------------------ 11
3. Product Specification ------------------------------------------------- 12
Page 3
S21315 / S21318 User Manual
ALLNET
GmbH
1. Introduction
The G1005D/G1008D 5/8-Port Desktop Gigabit Ethernet
Switch, mini and exquisite, is especially suitable for
small-sized networking. It provides 5/8 10/100/1000Mbps
Auto-negotiation ports and supports Auto MDI/MDIX.
These Gigabit ports can be used not only as ordinary ports,
but as Uplink ports connected to other networking devices.
You can replace the 10/100Mbps switch with the
G1005D/G1008D to resolve the bottleneck issues of server
terminal connectivity, because the speed at each port can
be up to 2000Mbps in full-duplex mode. It’s the best choice
for you to upgrade from the normal 10/100Mbps to
1000Mbps. Moreover, its easy setup and no network
management will benefit you a lot. So you can select this
Gigabit Switch as a prime switch to improve the speed
between different departments and servers.
Page 4
S21315 / S21318 User Manual
ALLNET
GmbH
1.1 Switch Features
Complies with IEEE802.3, IEEE802.3u and
IEEE802.3ab Ethernet standards
Supports Auto MDI/MDIX on each port
Supports NWAY Auto-Negotiation function
Provides 5/8 10/100/1000Mbps Auto-Negotiation
RJ-45 ports
Supports IEEE802.3x flow control for full-duplex
and Backpressure flow control for half-duplex
Provides up to 10/16Gbps backplane bandwidth
and non-blocking line speed forwarding
Supports store-and-forward switching method
Provides 8K MAC address entries and MAC
address self-learning/auto-aging
Desktop and mini plastic shell design
Page 5
S21315 / S21318 User Manual
ALLNET
GmbH
1.2 Package Contents
Please check the articles carefully after you open the
packing as below:
One 5/8-Port Desktop Gigabit Ethernet Switch
One Power Adapter
One User Guide
If any of the listed items are missing or damaged, please
contact the reseller from whom you purchased for
replacement.
Page 6
S21315 / S21318 User Manual
ALLNET
GmbH
1.3 Front Panel and Rear Panel Specifications
The front panel of 5/8-Port Desktop Gigabit Ethernet Switch
includes 5/8 Link/Act indicators and one power indicator.
Please refer to the detailed description of these indicators
in LED Indicator Specifications.
The front panel of the Switch
The Rear Panel of the Switch includes 5/8 10/100/1000Mbps
RJ-45 ports and one AC power port used for AC power
input.
The rear panel of the Switch
Notice: Please use the delivery-attached power adapter. If not,
the switch may be damaged.
Page 7
S21315 / S21318 User Manual
ALLNET
GmbH
1.4 LED Indicator Specifications
The LED indicators of the Switch include Power and 5/8
Link/Act indicators. You can see their operating situation
through these LED indicators.
The following chart shows the LED indicators of the Switch
along with explanation of each indicator.
Page 8
S21315 / S21318 User Manual
ALLNET
GmbH
LED
Color Status Description
Power
Green ON
This indicator lights
when the Switch turns
on.
— OFF
If this indicator is not
lighting, please check
the AC power connector
to ensure proper
connectivity of the
power cable and the
Switch.
Link/Act
Green
ON
Indicates the Switch is
connected at 1000Mbps.
Blinking
Indicates the Switch is
transmitting/receiving
data packets at
1000Mbps.
Orange
ON
Indicates the Switch is
connected at
10/100Mbps.
Blinking
Indicates the Switch is
transmitting/receiving
data packets at
10/100Mbps.
—
OFF
Indicates the connection
fails.
Page 9
S21315 / S21318 User Manual
ALLNET
GmbH
2. Installation
2.1 Before Connecting to the Network
Before connecting the G1005D/G1008D to the network,
please pay attention to the following instructions:
Don’t put heavy articles on the Switch.
Power sockets and equipments should be within 1.5
meters of the Switch.
Check power adapter to confirm the safe connection.
Make sure there’s adequate space for proper heat
dissipation and adequate ventilation around the
Switch.
Page 10
S21315 / S21318 User Manual
ALLNET
GmbH
2.2 Connecting to End Nodes
Use standard Ethernet cable to connect the Switch to end
nodes as described below. Switch ports will automatically
adjust to the characteristics (speed/duplex) of the device to
which is connected.
Switch connecting to an end node
Please refer to the LED Indicator Specifications. The
Link/Act LEDs for each port are turned on when the link is
available.
Page 11
S21315 / S21318 User Manual
ALLNET
GmbH
2.3 Switch to Router or Switch
Connecting to another router or switch
Please refer to the LED Indicator Specifications. The
Link/Act LEDs for each port are turned on when the link is
available.
Page 12
S21315 / S21318 User Manual
ALLNET
GmbH
3. Product Specification
Standards
IEEE802.3 10B
ase
-
T Ethernet
IEEE802.3u 100 Base-TX Fast
Ethernet
IEEE802.3
ab Gigabit Ethernet
Protocol CSMA/CD
Topology Star
Network Cables
10 Base
-T:
Cat.3 UTP or
above
100 Base-TX: Cat.5 UTP /STP
1000Base-T: Cat.5, Cat.5e or
Cat.6 UTP/STP
Speed 10/100/1000Mbps
Transmission Method store-and-forward
MAC Address Table 8K entries
Packet Filtering/
Forwarding Rate
14880pps(10Mbps)per port
148800pps
(
100Mbps
)
per port
1488000pps
(
1000Mbps
)
per port
MAC
Address Learning
Self-learning, auto-aging
Power External universal power supply
AC Input AC 9V 1200mA
Power Consumption 6W/7.2W
Operating Temperature
0OC ~40OC
Storage Temperature -40OC ~70OC
Operating Humidity
10%~90% RH no condensing
Storage Humidity
5%~90% RH no condensing
Page 13
S21315 / S21318 User Manual
ALLNET
GmbH
EC --- Declaration of conformity
For the following equirement:
Synergy21 S21315 & S21318 5/8 Port 10/100/1000 Ethernet Switch
The safety advice in the documentation accompanying the
products shall be obeyed. The conformity to the above
directive is indicated by the CE sign on the device.
The Synergy21 S21315 & S21318 5/8 Port 10/100/1000 Ethernet
Switch conforms to the Council Directives of EC EMC 2004/108/EC.
This equipment meets the following conformance standards:
EN: 55022: 2006
55024: 1998 + A1: 2001 + A2: 2003
61000-3-2:2006
61000-3-3:1995 + A1:2001 + A2:2005
This equipment is intended to be operated in all countries.
This declaration is made by
ALLNET Deutschland GmbH
Maistr. 2
82110 Germering
and can be downloaded from
http://www.allnet.de/ce-certificates/
Page 14
S21315 / S21318 User Manual
ALLNET
GmbH
Copyright © 2008. All rights reserved.
No part of this document may be reproduced, republished, or
retransmitted in any form or by any means whatsoever, whether
electronically or mechanically, including, but not limited to, by
way of photocopying, recording, information recording, or
through retrieval systems without the express written permission
of the owner. Product specifications contained in this document
are subject to change without notice. All other company or
product names mentioned are used for identification purposes
only and may be trademarks of their respective owners.
Manufacturer:
ALLNET GmbH
Page 15
S21315 / S21318 User Manual
ALLNET
GmbH
ALLNET Deutschland GmbH
Maistrasse 2
82110 Germering
Tel. +49 89 89 4222 22
Fax +49 89 89 42 24 33
email: info@allnet.de
Loading...