Synergy SQ, PM2, SQ/PM2 Instruction Manual
• 2 Extruded Posts
• Drill Bit
• FX200 Mount Kit
M (8x) 300-505
Cup Point Set Screw
K (2x) 300-555
2” Button Head
R
(2x) 301-422 Base Plate
F (4x) 300-485
Button Head Screw
L (4x) 300-470
Metal Washer
N
(1x) 400-060 3/16” Hex Key
O
(1x) 400-070 1/8” Hex Key
G(12x) 300-560
Flat Nut
P (2x) 301-425
Post Cover
Q (8x) 301-575
Plastic Fasteners
S
(5x) 301-600
Wire Manager
Synergy Quad Mount Hardware Bag - PHK-523
V
(4x) 300-460
A. Align thru holes in posts over the pins in the base plates.
Guide the at nuts (G) through the front of the posts.
If necessary, use rubber mallet or other device to ensure the
posts ts snugly against the top surface.
Tighten the screws (F) with hex key (H).
Thru Holes
B. Attach Both Base Plates as Shown
TIGHTEN FIRMLY WITH HEX KEY WRENCH.
A. Loosely assemble 2 at nuts (G) with 2 button
head screws (F) through each base plate (R).
F
R
G
BACK EDGE
N
K
L
L
V
R
AND
SYNERGY QUAD PANEL MOUNT
FOLD AND ALIGN THIS BEND WITH THE REAR OF THE CABINET.
POKE THROUGH
USING A PENCIL
POKE THROUGH
USING A PENCIL
TEMPLATE
SQ/PM2
2X - Along the rear edge of the cabinet, use template on the
edge of this page as a guide to drilling the hole. Line up one
hole on template with the center bolt and use the other as a
guide to mark where to drill your hole.
Use the center rear bolt as your template guide.
BEFORE YOU BEGIN
• This TV mount is intended for use with Flat-Panel TV 65” or smaller and a maximum weight capacity of 175lbs.
• Use with products heavier than the maximum weight or larger than the size indicated may result
in instability causing possible injury.
• Carefully inspect the mount for shipping damage or missing parts. If any damage is apparent or you are missing parts
contact Salamander Designs at 800-535-5659.
• Read ALL instructions before assembly. If you have any questions, please contact your installation contractor
or Salamander Designs.
• Mounts must be attached as specified in assembly instructions. Improper installation can result in serious personal injury.
REQUIRED HOLE LOCATIONS
TEMPLATE
MARK
& DRILL
GUIDE
MARK
& DRILL
PARTS
1. DRILLING HOLES
2. INSTALL BASE PLATES
3. INSTALL POSTS
B. Assemble 8 at nuts (G) with 8 set screws (M) and
drop into the left and right sides of each post.
C. Position the set screws (M) into the thru holes and tighten
through to the base plate pins. This will lock the posts to
the top of your Synergy cabinet.
Tighten firmly with hex key (O).
Refer to Step 2 in the FX200 Manual
Salamander Designs Ltd. www.salamanderdesigns.com 800-535-5659
11.10v /988-005 .oN coD .dtL sngiseD rednamalaS 0102 ©
Thread the screws to the nuts enough to ensure the
nut does not fall off.
Assemble 1 Button Head Screw with Washer
through the the appropriate slot (4 places) with
flat nuts loosely on each.
Slide the post bra cket into the posts as shown below,
guiding the flat nuts (G) to ensure all par ts slide freely.
Position the post bra cket vertically along the posts where
you wish the center of the television to rest.
Tighten button hea d screws (F) with hex hey (H) to fi rmly
set the bra cket onto the posts.
Q
P
Squeeze to remove.
S
6. INSTALL POST BRACKET
WIRE MANAGERS & CAPS
7. HANG TV
B
Center TV Brackets (II) on Wall Bracket (I)
and push black Click Fasteners up into
lock position.
C
Install Pad Lock (IV).
A
Pull on black cord to unlock Click
Fasteners and hook TV Brackets (II)
onto Wall Bracket (I) from top.
G
M
F
L
G
G
G
G
L
F
F
F
O
Thru Holes
LIMITED WARRANTY- For five full years Salamander Designs Ltd. will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other equipment consequential to our equipment failure.
Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any
damage incurred in a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via
UPS within the continental U.S.A. only.
4. ASSEMBLE TV BRACKETS
5. ASSEMBLE POST BRACKETS
Loading...