BRIGHT SOLUTIONS
PLATINUM SERIES Kit
HEADLAMP Resurfacer / Protector
Thank you for purchasing BRIGHT SOLUTIONS
PLATINUM SERIES Kit, this is a 3 or 4 STEP process that
takes approximately 5~10 MINUTES to perform per headlamp
dependent upon severity of damage of lamp lens. By applying the
patented Preserver, your headlamp cleaning will be preserved for
more than two years.
Can Be Used on
Turn Signal Lights Reflective Lens Covers
: Headlamps Taillights
KEEP OUT OF THE REACH OF CHILDREN
DO NOT ALLOW PRODUCT TO FREEZE
WHEN APPLYING PRODUCT IN TEMPERATURES
o
BELOW 60
, TURN LAMPS ON UNTIL WARM.
DO NOT APPLY SHINE RESTORER/ PROTECTOR IN
DIRECT SUNLIGHT
READ INSTRUCTIONS IN ENTIRETY BEFORE USE.
USE GLOVES TO PROTECT HANDS.
FIRST determine the extent of damage that has occurred over time to
your headlamp lens.
IF
Headlamp lens is slightly fogged and or yellowed, without
visible hairline scratches or crazing, in most cases, the lamp
could be simply cleaned clear without sanding.
and 4
IF
Headlamp lens has extensive yellowing, scratches, crazing,
and/or pits, sanding is necessary to obtain a successful
result. Regardless of damage, sanding during cleaning will
speed the process dramatically.
STEP 1
CLEANING
Remove all contents from package.
Using a paper towel, fold in quarters (1).
Thoroughly shake the Water Based Pretreatment before applying to
towel.
Open the specially formulated Water Based Pretreatment, saturate the
Continue cleaning, changing the towel surface and adding more Water
When dirt and discoloring ceases to be removed from lens, Proceed to
towel (2), and begin cleaning the entire lens with a circular
motion (3).
Based Pretreatment as towel becomes discolored (4) with dirt
and oxidation film of lamp lens.
STEP 2 or 3
.
Steps 1, 2 ,3 and 4
Steps 1, 3
PAGE 1
2
5
8
11
Less than Five
Minutes Drying
Time
STEP 2
1 3
4
7
10
SANDING
NOTE: Masking area around headlamp (5) is highly
recommended to assure that painted and/or chromed
surfaces are not harmed during sanding process
Have a spray bottle of water handy (6), start with 600 grit sanding disc
applied to rotary sander, spray lens with water and begin sanding
the entire surface of the lens, wetting lamp (7) as needed to
prevent buildup of particles.
Note: Removal of deteriorated material should be fairly
quick.
Continue sanding until all discolored plastic has been removed from
lamp surface and residue of sanding is white in appearance.
Sanding is complete when lamp lens is uniform in appearance.
Take the 1500 grit sanding disc, apply to rotary sander, spray lens with
water and sand the entire surface of the lens, wetting lens (7) as
needed. This process will reduce the sanding lines .
Proceed to
STEP 3
STEP 3
POLISHING
Apply polishing disc to rotary sander
Thoroughly shake the HEADLAMP CLEANER/POLISH, shaking
container frequently throughout the cleaning process.
Open the specially formulated HEADLAMP CLEANER/POLISH,
saturate a small area of the polishing pad (8), and begin cleaning
the entire lens with a circular motion (9).
STEP 3 (continued)
POLISHING
Continue polishing and adding more HEADLAMP CLEANER/
POLISH as necessary to polish the entire lamp lens.
When lens has achieved a highly polished appearance, wipe off all
polish residue with Water Based Pretreatment
Proceed to
6
STEP 4
STEP 4
.
SHINE RESTORER / PRESERVER
APPLICATION
Use a lint free towel and fold in quarters (1).
Safety by Design
9
NOTE:
Apply SHINE RESTORER/ PROTECTOR
out of direct sunlight. WHEN APPLYING
PRODUCT IN TEMPERATURES BELOW 60
TURN LAMPS ON UNTIL WARM
o
,
Apply a liberal amount of the SHINE RESTORER/
PROTECTOR to a clean lint-free paper towel (10) and
apply it smoothly across the plastic surface (11), avoiding any
runs or bubbling. Do not wipe until dry or tacky, wipe on
wet, stand back and let dry
To remove SHINE RESTORER/PROTECTOR from
other surfaces when wet, rinse with water and wipe off with
a dry towel.
Multiple coats of SHINE RESTORER/PROTECTOR, two
coats are recommended to increase the shine and protection
properties.
Plastic surface must be dry to the touch prior to each application
of additional coats. Average drying time between coats is
less than 5 minutes.
As with any repair versus replacement, some items will not
achieve like new results. If directions are followed, significant
improvement in the appearance of the items will be achieved.
As we are unable to supervise the application process, user
assumes all risks. The manufacturer and its distributors are
not liable for any damages incurred by the use of this product.
If you are unsure as to the application process or compatibility
of the item you would like to resurface, please contact the
manufacturer or distributor for advice on how to proceed.
524 S.E. Transport Drive
Lee’s Summit, Missouri 64081
816-525-9263 FAX: 816-525-9383
www.symtechcorp.net
PAGE 2
SAFETY and HEALTH WARNINGS
ALL PRODUCTS INCLUDED IN THIS KIT:
IN CASE OF CHEMICAL
EMERGENCY CONTACT:
INFOTRAC @ (800)-535-5053
BRIGHT SOLUTIONS,
WATERBASE PRETREATMENT
Inhalation: Do not inhale. If symptoms develop, move
individual to fresh air. Seek medical attention if
symptoms persist. Product is not known to be a
Swallowing: Do not swallow. In case of accidental ingestion,
Skin: Contact may cause minimal skin irritation. Flush
Eyes: Contact with eyes may cause irritation. Flush
health hazard.
immediately give 2 glasses of water orally and
induce vomiting. Seek medical attention.
skin with generous amounts of water. If
irritation persists, seek medical attention
eyes gently with generous amounts of water. If
irritation persists, seek medical attention.
BRIGHT SOLUTIONS
SHINE RESTORER / PROTECTOR:
Inhalation: Do not inhale. If symptoms develop,
immediately move individual to fresh air. If
symptoms persist, seek medical attention.
Product is not known to be harmful.
Swallowing: Do not swallow product. May cause
gastrointestinal irritation, nausea, and diarrhea.
Give 2-3 large glasses of water. Seek medical
attention. Product is not known to be toxic.
Skin: Wear gloves to protect hands. Wash area with
soap and water. If irritation develops, seek
medical attention.
Eyes: Contact may cause irritation. Flush eyes gently
with water for at least 15 minutes while holding
eyelids apart. If irritation persists, seek medical
attention.
None of the chemical combinations listed are classified as a
carcinogen or potential carcinogen. Chemical combinations
are not listed with IARC, National Toxicology Program, or
OSHA. Respiratory protection is not required when chemicals are used as instructed.
BRIGHT SOLUTIONS,
HEADLIGHT CLEANER/POLISH:
Inhalation: Do not inhale. If symptoms develop, move
individual to fresh air. Seek medical attention if
symptoms persist. Product is not known to be a
health hazard.
Swallowing: Do not swallow. In case of accidental ingestion,
immediately give 2 glasses of water orally and
induce vomiting. Seek medical attention.
Skin: In case of irritation to skin, flush skin with
generous amounts of water. If irritation persists,
seek medical attention
Eyes: Contact with eyes may cause irritation. Flush
eyes gently with generous amounts of water. If
irritation persists, seek medical attention.
NOTES:
BROUGHT to YOU
by
Safety by Design
Manufactured for Symtech Corporation
by Coliance Corporation.
Revised 1/2009
Loading...