Symtech Headlight Cleaner Kit User Manual

BRIGHT SOLUTION

HEADLAMP CLEANER / POLISH

Thank you for purchasing BRIGHT SOLUTIONS CLEANER
this is a 1 to 2 STEP process that takes approximately 10~15
MINUTES to perform per headlamp dependent upon severity of
damage of lamp lens.

Can Be Used on

Turn Signal Lights Reflective Lens Covers

: Headlamps Taillights

KEEP OUT OF THE REACH OF CHILDREN

DO NOT ALLOW PRODUCT TO FREEZE

DO NOT APPLY IN DIRECT SUNLIGHT

READ INSTRUCTIONS IN ENTIRETY BEFORE USE.

USE ENCLOSED GLOVES TO PROTECT HANDS..

FIRST determine the extent of damage that has occurred over time to

your headlamp lens.

IF

Headlamp lenses are slightly fogged and or yellowed,

without visible hairline scratches or crazing, in most cases
the lamp can be simply cleaned clear without the use of
sandpaper STEP 1.

IF

Headlamp lenses have extensively yellowed, have scratches,

crazing and/or pits, sanding is necessary to obtain a
successful result STEP 1 (
damage, using sandpaper during cleaning will speed the
process dramatically.

STEP 1
CLEANING

Remove all contents from package.

Select one of the towels and fold in quarters (1).

Thoroughly shake the BRIGHT SOLUTIONS HEADLAMP

CLEANER/POLISH before applying to towel. Shake the
container frequently throughout the cleaning process.

Open the specially formulated BRIGHT SOLUTIONS

HEADLAMP CLEANER/POLISH, saturate a small area of
the towel (2), and begin cleaning the entire lens with a circular
motion (3).

Continue cleaning, changing the towel surface and adding more

HEADLAMP CLEANER/POLISH as towel becomes
discolored (4) with dirt and oxidation film of lamp lens.

When dirt and discoloring ceases to be removed from lens, allow

cleaner to dry and buff to a high sheen (7).

OPTIONAL

). Regardless of

STEP 1

1

4 5

2

7

(OPTIONAL)

3

6

SANDING / CLEANING

Empty contents of package and fill cavity of package with water (4), start

with 1500 grit sandpaper, dampen sandpaper with water (5) and
begin sanding the entire surface of the lens, wetting sandpaper (5) as
needed to prevent buildup of particles. Sanding is complete when
lamp lens is uniform in appearance.

Note: ALWAYS sand in a straight motion (6), DO NOT use a

Take the 2000 grit sandpaper and dampen (5), again sand the entire surface

of the lens, wetting sandpaper (5) as needed to prevent buildup of
particles. This process will reduce the sanding lines .

Select one of the towels and fold in quarters (1).

Thoroughly shake the BRIGHT SOLUTIONS HEADLAMP

CLEANER/POLISH before applying to towel. Shake the container
frequently throughout the cleaning process.

Open the specially formulated BRIGHT SOLUTIONS HEADLAMP

CLEANER/POLISH, saturate a small area of the towel (2), and
begin cleaning the entire lens with a circular motion.

Continue cleaning and polishing, adding more HEADLAMP

CLEANER/POLISH as necessary to polish the entire lamp lens

When lens has achieved a highly polished appearance, wipe off all polish

residue and buff to a high sheen (7)

circular motion.

Note: ALWAYS sand in the same direction as previous step and

in a straight motion (6), DO NOT use a circular motion.

As with any repair versus replacement, some items will not

achieve like new results. If directions are followed,
significant improvement in the appearance of the items will
be achieved. As we are unable to supervise the application
process, user assumes all risks. The manufacturer and its
distributors are not liable for any damages incurred by the
use of this product. If you are unsure as to the application
process, or compatibility of the item you would like to
resurface, please contact the manufacturer, or distributor for
advise on how to proceed.

SAFETY and HEALTH

WARNINGS

ALL PRODUCTS INCLUDED IN THIS KIT ARE ON

REVERSE SIDE

Safety by Design

524 S.E. Transport Drive

Lee’s Summit, Missouri 64081

816-525-9263 FAX: [phone]

www.symtechcorp.net

SAFETY and HEALTH WARNINGS

ALL PRODUCTS INCLUDED IN THIS KIT:

IN CASE OF CHEMICAL

EMERGENCY CONTACT:

INFOTRAC @ (800)-535-5053

BRIGHT SOLUTIONS,
HEADLIGHT CLEANER:
Inhalation: Do not inhale. If symptoms develop, move

individual to fresh air. Seek medical attention if
symptoms persist. Product is not known to be a

Swallowing: Do not swallow. In case of accidental ingestion,

Skin: In case of irritation to skin, flush skin with

Eyes: Contact with eyes may cause irritation. Flush

health hazard.

immediately give 2 glasses of water orally and
induce vomiting. Seek medical attention.

generous amounts of water. If irritation persists,
seek medical attention

eyes gently with generous amounts of water. If
irritation persists, seek medical attention.

None of the chemical combinations listed are classified as a

carcinogen or potential carcinogen. Chemical combinations
are not listed with IARC, National Toxicology Program, or
OSHA. Respiratory protection is not required when
chemicals are used as instructed.

Safety by Design

524 S.E. Transport Drive

Lee’s Summit, Missouri 64081

816-525-9263 FAX: [phone]

www.symtechcorp.net

Manufactured for Symtech Corporation
by Coliance Corporation

BROUGHT to YOU

by

Safety by Design

REVISED 10/2008