Symtech Gold User Manual

BRIGHT SOLUTIONS

Gold Series

HEADLAMP Resurfacer / Protector

Thank you for purchasing BRIGHT SOLUTIONS, Gold Series
this is a 3 or 4 STEP process that takes approximately 10~15
MINUTES to perform per headlamp dependent upon severity of
damage of lamp lens. By applying the patented Preserver, your
headlamp restoration will be preserved for more than two years.

Can Be Used on

Turn Signal Lights Reflective Lens Covers

: Headlamps Taillights

KEEP OUT OF THE REACH OF CHILDREN

DO NOT ALLOW PRODUCT TO FREEZE

WHEN APPLYING PRODUCT IN TEMPERATURES

o

BELOW 60

, TURN LAMPS ON UNTIL WARM.

DO NOT APPLY SHINE RESTORER/ PROTECTOR IN

DIRECT SUNLIGHT

READ INSTRUCTIONS IN ENTIRETY BEFORE USE.

USE GLOVES TO PROTECT HANDS.

RECOMMENDED

FIRST determine the extent of damage that has occurred over time to

your headlamp lens.

IF

Headlamp lens is slightly fogged and or yellowed, without

visible hairline scratches or crazing, in most cases, the lamp
can be simply cleaned clear without the use of sandpaper.

Steps 1, 3 and 4

IF

Headlamp lens has extensive yellowing, scratches, crazing

and/or pits, sanding is necessary to obtain a successful
result. Regardless of damage, using sandpaper during
cleaning will speed the process dramatically.

Steps 1, 2 ,3

STEP 1
CLEANING

2

5

8

Five Minutes
Drying Time

STEP 2

1

4

7

SANDING

Fill a container, or spray bottle with water (5), start with 1500 grit

sandpaper, dampen with water and begin sanding the entire
surface of the lens, wetting sandpaper (6), or lens as needed to
prevent buildup of particles. Sanding is complete when lamp
lens is uniform in appearance.

Note: ALWAYS sand in a straight motion (7), DO NOT use

a circular motion.

Continue sanding until all discolored plastic has been removed from

lamp surface and residue of sanding is white in appearance.

Take the 2000 grit sandpaper, dampen with water and sand the entire

surface of the lens, wetting sandpaper (6) as needed. This
process will reduce the sanding lines .

Note: ALWAYS sand in the same direction as previous step

and in a straight motion (7), DO NOT use a circular
motion.

STEP 3
POLISHING

STEP 4
SHINE RESTORER/PRESERVER

Select a LINT-FREE paper shop towel and fold in quarters (1).

3

NOTE:

Apply SHINE RESTORER/ PROTECTOR out
of direct sunlight. WHEN APPLYING PRODUCT
IN TEMPERATURES BELOW 60

Safety by Design

ON UNTIL WARM

o

, TURN LAMPS

Apply a liberal amount of the SHINE RESTORER/

PROTECTOR to a clean lint-free paper towel (8) and apply it

6

smoothly across the plastic surface (9), avoiding runs and
bubbling. Do not wipe till dry or tacky, wipe on wet, stand back
and let dry

To remove SHINE RESTORER/PROTECTOR from other
surfaces when wet, rinse with water and wipe off with a dry
towel.

9

Multiple coats of SHINE RESTORER/PROTECTOR are

recommended to increase the shine and protection properties.

Plastic surface must be dry to the touch prior to each application of

additional coats.

As with any repair versus replacement, some items will not

achieve like new results. If directions are followed, significant
improvement in the appearance of the items will be achieved. As
we are unable to supervise the application process, user assumes all
risks. The manufacturer and its distributors are not liable for any
damages incurred by the use of this product. If you are unsure as
to the application process or compatibility of the item you would
like to resurface, please contact the manufacturer or distributor for
advice on how to proceed.

SAFETY and HEALTH

WARNINGS

ALL PRODUCTS INCLUDED IN THIS KIT ARE ON

REVERSE SIDE

Select a paper shop towel and fold in quarters (1).

Thoroughly shake the BRIGHT SOLUTIONS Pretreatment

before applying to towel.

Open the specially formulated BRIGHT SOLUTIONS

Pretreatment, saturate the towel (2), and begin cleaning the
entire lens with a circular motion (3).

Continue cleaning, changing the towel surface and adding more

Pretreatment as towel becomes discolored (4) with dirt and
oxidation film of lamp lens.

When dirt and discoloring ceases to be removed from lens, Proceed to

STEP 2 or 3

.

Select a paper shop towel and fold in quarters (1).

Thoroughly shake the BRIGHT SOLUTIONS HEADLAMP

CLEANER/POLISH before applying to towel. Shake the
container frequently throughout the cleaning process.

Open the specially formulated BRIGHT SOLUTIONS

HEADLAMP CLEANER/POLISH, saturate a small area of
the towel (2), and begin cleaning the entire lens with a circular
motion (3).

Continue polishing and adding more HEADLAMP CLEANER/

POLISH as necessary to polish the entire lamp lens.

When lens has achieved a highly polished appearance, wipe off all

polish residue with Pretreatment

Proceed to

STEP 4

.

524 S.E. Transport Drive

Lee’s Summit, Missouri 64081

816-525-9263 FAX: [phone]

www.symtechcorp.net

SAFETY and HEALTH WARNINGS

ALL PRODUCTS INCLUDED IN THIS KIT:

IN CASE OF CHEMICAL

EMERGENCY CONTACT:

INFOTRAC @ (800)-535-5053

BRIGHT SOLUTIONS, PRETREATMENT:

WARNING: FLAMMABLE

DO NOT USE OR STORE NEAR FIRE, FLAME, SPARK OR

DO NOT SMOKE NEAR PRODUCT

Inhalation: Do not inhale. Breathing in small amounts during

Swallowing: Do not swallow product. Seek medical attention

Skin: Wear gloves to protect hands. May cause mild skin

Eyes: May cause eye irritation. If symptoms develop,

HEAT SOURCE.

normal handling is not likely to cause harmful
effects. Breathing large amounts of product may
be harmful. If symptoms develop, immediately
move individual into fresh air. Seek immediate
medical attention.

immediately.

irritation and burning. Wash area with soap and
water. If symptoms persist, seek medical attention.

immediately move individual to fresh air. Flush
eyes gently with water for at least 15 minutes while
holding eyelids apart. Seek immediate attention.

BRIGHT SOLUTIONS
SHINE RESTORER/ PRESERVER:
Inhalation: Do not inhale. If symptoms develop,

immediately move individual to fresh air. If
symptoms persist, seek medical attention.

Swallowing: Do not swallow product. Seek medical

attention. Product is not known to be toxic.

Skin: Wear gloves to protect hands. Wash area with

soap and water. If irritation develops, seek
medical attention.

Eyes: Contact may cause irritation. Flush eyes gently

with water for at least 15 minutes while holding
eyelids apart. Seek medical attention.

None of the chemical combinations listed are classified as a

carcinogen or potential carcinogen. Chemical combinations
are not listed with IARC, National Toxicology Program, or
OSHA. Respiratory protection is not required when
chemicals are used as instructed.

BRIGHT SOLUTIONS,
HEADLIGHT CLEANER/POLISH:
Inhalation: Do not inhale. If symptoms develop, move

individual to fresh air. Seek medical attention if
symptoms persist. Product is not known to be a
health hazard.

Swallowing: Do not swallow. In case of accidental ingestion,

immediately give 2 glasses of water orally and
induce vomiting. Seek medical attention.

Skin: In case of irritation to skin, flush skin with

generous amounts of water. If irritation persists,
seek medical attention

Eyes: Contact with eyes may cause irritation. Flush

eyes gently with generous amounts of water. If
irritation persists, seek medical attention.

Safety by Design

524 S.E. Transport Drive

Lee’s Summit, Missouri 64081

816-525-9263 FAX: [phone]

www.symtechcorp.net

Manufactured for Symtech Corporation
by Coliance Corporation.

BROUGHT to YOU

by

Safety by Design

REVISED 10/2008