Page 1
3 SPEED FAN & LIGHT
WALL CONTROL WITH
SMART CONTROL RECEIVER
INSTALLATION INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
GENERAL INFORMATION
This wall control is designed to separately control your ceiling fan speed and light brightness.
The fan button will control the fan speed. (Hi, Medium, Low)
The light buttons will control the lights, brightness dimmer and off.
The red indicator on the transmitter will light when the button is pressed.
NOTE: When installing the remote
control, be sure your fan control or
pull chain switch are in the "HIGH
SPEED" position and the light
control or switch is set to "ON".
INSTALLATION AND OPERATING INSTRUCTIONS
NOTE: This unit is equipped with an automatically learned type remote control. There are no frequency switches on the receiver and
transmitter; the receiver unit will automatically scan the frequency from the handheld remote if any changes are made. This unit has 65,000
different code combinations.
1. INSTALLING RECEIVER IN THE CEILING FAN
A. Safety precautions:
WARNING: HIGH VOLTAGE! Household electrical power can cause serious injury or death. Disconnect the source of electrical power
to the ceiling fan by removing the fuse or switching off the circuit breaker.
B. Installing receiver in fan.:
a. Remove the ceiling fan canopy from the mounting bracket.
b. Disconnect the existing wiring between the ceiling fan and supply at the electrical junction box.
c. Make the connections as follows, using the wire nuts supplied: (Fig. B)
CONNECT TO
Green fan wire...........................................Bare supply wire
Black receiver wire (AC IN L)..................Black supply wire
White receiver wire(AC IN N)..................White supply wire
White receiver wire (TO MOTOR N).......White fan wire
Black receiver wire (TO MOTOR L)........Black fan wire
Blue receiver wire(FOR LIGHT)..............Blue light wire
AC SUPPLY
WHITE
BLACK
RECEIVER
BLUE BLUE
Fig. A
RECEIVER
BLACK
WHITE
BARE GREEN
Fig. B
BLACK
WHITE
If other fan or supply wires are different color, have this unit installed by a qualified electrician.
d. Push all connected wires up into junction box.
e. Reinstall the canopy on the mounting bracket.
f. Restore the electrical power.
2. INSTALLING THE WALL TRANSMITTER
WARNING! HOOK UP "IN SERIES" ONLY. DO NOT CONNECT NEUTRAL SUPPLY WIRE OF ELECTRIC CIRCUIT TO THE
TRANSMITTER WALL SWITCH, DAMAGE TO THE TRANSMITTER WALL SWITCH AND POSSIBLE FIRE COULD OCCUR.
a. Remove the existing wall plate and switch from the wall outlet box.
b. Make the electrical connections as shown in Fig. C. If your outlet box has a ground wire (Green or Bare Copper) connect the Transmitter's
ground wire directly to one of the screws from the outlet box . Secure all wire connections with the plastic wire nuts provided.
c. Carefully tuck the wire connections inside the outlet box. Use the screws provided to secure the wall transmitter and wall plate to the outlet
box. (Fig. D)
Page 2
AC 12 0V
IN PU T
WHITE
BLACK
GREEN
BLACK
BLACK
GROUND
WALL
BLACK
CONTROL
BLACK
Fig. C Fig. D
BLACK
AC S UPP LY
WHITE
BLU E
BLA CK
WHI TE
GRO UND
GRE EN
BLU E
WHI TE
BLA CK
3. OPERATING TRANSMITTER:
A. Store the transmitter away from excess heat or humidity.
B. Remove cover by snapping off from top or bottom, install 12V battery located in the wall transmitter, Duracell MN21/Eveready A23/GP
23A all 12V. (Fig. G)
NOTE:
To prevent damage to the transmitter, remove these batteries if not used for long periods of time (months).
C. Operation buttons on the panel of the transmitter: (Figure G)
HI button - for fan high speed.
MED button - for fan medium speed.
LOW button - for fan low speed.
FAN OFF button - for fan speed off.
OFF-ON Slide Button-This button turns the power Off and On to the Fan and Light(s).
The"LIGHT" button: This Button will control the light brightness.
the
button
down to increase or decrease the light. Tap the
button
The light function is controlled by pressing the "
LIGHT" button
quickly to turn the light off or on. If you press the button in excess of 0.7
seconds it becomes a dimmer. The light varies cyclically in 0.8 seconds. The light key has auto resume, so it will stay at the same
brightness as the last time it was turned off.
Remote pairing process:
NOTE: The ”
With the fan’s power off, restore power to the fan. Press and hold “FAN OFF” button for about 5 seconds and release. If optional
light kit is installed, the light kit will flash twice and the signal light on the handheld remote will come on when the button is
pressed. The fan has completed the pairing process with the handheld remote and is ready for use.
Fig.G Fig.H
YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT.
4. TROUBLESHOOTING GUIDE
A. Fails to operate:
a. Power to the receiver?
b. Receiver wired correctly?
c. Fan manual speed control in highest position?
d. Light kit switch turned on?
e. Code set at exact same position in both transmitter and receiver?
B. Won't operate at distance: .
If transmitter operates the fan and the light kit when up close, but not a 30 feet
away.
FAN OFF
” button must be pressed within 60 seconds of restoring power.
HI
LIGHT
MED
LOW
FAN OFF
23AE 12V
NOTICE!
Your ceiling fan and light kit assembly must meet
the following requirements:
1. Do not use with solid state fans.
2. Electrical rating: 120V / 60 Hz
MAX. motor amps:1.0 A
MAX. light watts: 250 W
(Incandescent only)
. Hold
Loading...