Page 1
Fireplace
Installation & Assembly
Preparation
This product includes a GLASS panel! Always use extreme caution when handling
glass. Failure to do so could result in personal injury or property damage.
Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts
and assembly steps are grouped for wall-hanging use. Check the parts list to make sure nothing is
missing. Dispose of packaging materials properly. Please recycle whenever possible.
You will need the following tools (not included): Phillips screwdriver; stud finder; level; tape
measure; electric drill; 1/4” wood drill bit, hammer.
Parts and Hardware
B – Wood Screws ( 6 ) C – Drywall anchors (6 )
A – Fireplace ( 1 )
D – ST4x8 Metal Screws (2) RC – Remote Control
E - Wall Bracket (1)
F - Decorative Crystals
Installation and Assembly
Rear View of
19.7”
(50 cm)
Minimum 39.4”
(100 cm)
19.7”
(50 cm)
Minimum 19.7”
(50 cm)
Step 1. Find a safe location.
Minimum clearance on each side: 19.7” (50
cm).
Minimum clearance below: 19.7” (50 cm).
Minimum clearance above: 39.4” (100 cm).
Minimum clearance from the front and sides:
3 feet (90 cm).
Choose a location near an outlet so an
extension cord is not required.
DO NOT position the unit directly below a
power outlet.
See Safety Information on pages 2 and 3
for warnings about safe placement, safe
installation, and proper use of this product.
4
Page 2
5
ST3.5x35mm
STEP1 ) Select a location that is not prone to moisture and is located at least 36" away from
combustible materials such as curtain drapes, furniture, bedding, paper, etc. then use a ￠7 drill bit to
drill the holes and use the Hammer to thread the Drywall anchors (C) into the hole till it keep flat with
the wall.
STEP2 ) Using the six wood screws (B) to fix the wall bracket , with wood screws thread the wall
bracket and to lock with the drywall anchors, please tighten all wood screws.
(6PCS)
C
NOTICE
The wall mount fasteners included with this fireplace are for use ONLY with a
wood-framed wall covered in drywall (sheet rock). For concrete walls, cinder
blocks, or other wall types, consult a professional for the best attachment methods.
Page 3
6
STEP 3) Have two people lift the fireplace machine up and insert the slots ( 2 slots on back of
fireplace box) to the wall bracket hooks.
STEP 4) With the fireplace installed safely, then using screws driver to lock the bracket and fireplace
with two ST4x8 (D) screws in both sides.Check the appliance for stability ensuring that the appliance
will not pull free from the wall.
Page 4
7
NOTE: To place to decorative crystals, follow these steps. Have a capable adult help you.
STEP 6A. While one person holds the glass panel, remove the two screws at the top edge of the
fireplace with a Phillips (+) screwdriver.
STEP 6B. Together, carefully remove the front glass panel and set it aside on a clean soft surface.
STEP 6C. Arrange the decorative crystals (F) on the shelf in the desired position.
STEP 6D. Set the front glass panel back onto the firebox.
STEP 6E. Align the tabs of the glass panel with the holes on the top edge of the fireplace. Thread
the screws back into the holes and tighten them both with a Phillips screwdriver.
ALWAYS keep the decorative crystals OUT OF REACH OF CHILDREN!Leave no
pieces where children can find them. Failure to do so could cause a choking hazard.
This next step involves GLASS! ALWAYS use extreme caution when handling glass.
Failure to do so could result in personal injury or property damage.
Loading...