Page 1
16� INCH� ELECTRIC� FIREPLACE� WITH� REMOTE�
OWNERS� MANUAL
Only use this heater as described in this manual. Any other use is not recommended
by the manufacturer, and may cause fire, electric shock, or other personal injury.
WARNING! Read and understand this entire owner’s manual, including all safety
information, before plugging in or using this product. Failure to do so could result in fire,
electric shock, serious personal injury, or death.
WARNING! INDOOR use only! NEVER use this heater outdoors!
SAVE THESE INSTRUCTIONS!
CAUTION! Keep this owner’s manual for future reference. If you sell or give this product
away, make sure this manual accompanies this product.
1
Page 2
IMPORTANT SAFETY INFORMATION!
WARNING
ALWAYS keep electric cords, home furnishings, drapes, clothing, papers,orother
combustibles at least 3 feet (0.9m) away from the front of this heater, and away from the
bottom, sides, and rear of this heater.
DO NOT place the heater near a bed because objects such as pillows or blankets can fall
off the bed and be ignited by the heater.
DO NOT COVER this heater or block the air vents at all. Doing so could cause a fire.
AVOID fire or electric shock! NEVER insert or allow any foreign objects to enter the
ventilation or exhaust openings of this heater.
Prevent Fire! Keep all flammable liquids, like gasoline or paint, away from this heater. This
heater produces arcing sparks that could ignite flammable liquids.
DO NOT cover this heater in any manner. Doing so could block the air flow and cause the
unit to overheat, or could ignite the material covering the heater.
NEVER run the power cord under carpet, rugs, runners, or any other covering. Doing so
could cause the cord or materials covering the cord to overheat.
AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other
blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.
WARNING
For residential use only! NOT for commercial use! NEVER use this fireplace for other than
its intended purpose.
ALWAYS HANG UNIT BEFORE USE. DO NOT turn on or use while the unit is sitting on the
floor, ground, or other surface.
The wall mount system is designed for use ONLY with this product. NEVER use a wall
mount system from another manufacturer.
Use extreme caution if using this heater near children, or where children may be present.
NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.
This heater is hot when in use. AVOID INJURY! DO NOT TOUCH hot surfaces, or attempt
to move this heater while it is hot.
ALWAYS turn this heater off before unplugging it from the outlet.
AVOID INJURY! Keep the cord from crossing traffic areas to avoid tripping.
NEVER modify this fireplace. Doing so could result in personal injury or property damage.
Modification of this fireplace completely voids all warranties.
Discontinue use if this fireplace malfunctions or is dropped or damaged in any manner.
ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet.
2
Page 3
WARNING
Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
ALWAYS disconnect this unit from the power supply before performing any assembly or
cleaning, or before relocating the electric fireplace.
NEVER use this heater in bathrooms, laundry rooms, or any other location where the
heater could fall into a bathtub or pool, become damp or come in contact with water.
NEVER hang this unit on a wall directly below an electrical outlet.
NEVER operate this heater if the power cord or plug has become damaged, or if the
grounding pin is damaged or missing.
Place the heater near a wall outlet so an extension cord is not needed. ALWAYS plug
heaters directly into a wall outlet/receptacle. NEVER use with an extension cord or
relocatable power tap (outlet/power strip).
Avoid hazards due to resetting of the thermal cut-off switch. NEVER control this unit with a
timer, or allow it to be on a circuit regularly switched off by the utility.
ONLY usethisheaterona110-120 Volt 15 Amp grounded circuit. NEVER overload the
circuit. If this heater trips the circuit breaker, unplug all other appliances on the same circuit
before the next use. Avoid plugging other appliances into the same circuit as this heater.
NEVER plug this heater into an outlet that is old, cracked,orhasanyloose wires or
connections. Plugging this heater into a faulty outlet could result in electric arcing within
the outlet that could cause the outlet to overheat or catch fire.
ALWAYS check your heater cord and plug connections with each use!
i) MAKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or loose plugs
can cause the outlet to overheat.
ii) Heaters draw more current than small appliances. Overheating may occur even if it
has not occurred with the use of other appliances.
iii) During use check frequently to see if the plug outlet or face plate is HOT!
iv) If the outlet or face plate is HOT, discontinue use immediately and have a qualified
electrician inspect and/or replace the faulty outlets.
SAVE THESE INSTRUCTIONS
3
Page 4
Preparation
This product includes a GLASS! Always use extreme caution when handling glass.
Failure to do so could result in personal injury or property damage.
Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Check
the parts list to make sure nothing is missing. Dispose of packaging materials properly. Please
recycle whenever possible.
You will need the following tools (not included): Phillips screwdriver; stud finder; level; tape
measure; electric drill; 1/4” wood drill bit, 1/16” wood drill bit, and a hammer.
Parts and Hardware
B – Wood Screws ( 3) C – Drywall anchors ( 3)
A –Fireplace(1)
RC – Remote Control
Decorative Crystal
4
Page 5
Installation and Assembly
Note: The installation must be done by two persons at least.
1.Take the fireplace out of the package, and place it on a flat, non-abrasive surface.
2. Remove off the screws on both sides with a Phillips screwdriver, then take off the wall bracket.
The bracket must be held tightly while screws are being removed, to avoid them from falling on the
fireplace and causing damage or injury.
5
Page 6
Wall mounted installation
(
)
Rear View of Fireplace
19.7”
(50 cm)
Minimum 39.4”
(100 cm)
19.7”
(50 cm)
Step 1. Find a safe location.
Minimum clearance on each side:
19.7” (50 cm).
Minimum clearance below:
19.7” (50 cm).
Minimum clearance above:
39.4” (100 cm).
Minimum clearance from the front :
3 feet (90 cm).
Choose a location near an outlet so
never use an extension cord.
DO NOT position the unit directly
below a power outlet.
See Safety Information on pages
2and3for warnings about safe
placement, safe installation, and
proper use of this product.
NOTICE
ALWAYS unplug this fireplace heater before assembly or cleaning, or before
relocating. Failure to do so could result in electric shock, fire,orpersonal injury.
Minimum
19.7”
50 cm
The wall mount fasteners included with this fireplace are for use ONLY with a
wood-framed wall covered in drywall (sheet rock). For concrete walls, cinder
blocks, or other wall types, consult a professional for the best attachment methods.
6
Page 7
Drywall
Studs
STEP 2. A. Locate the wall studs using an electronic stud-finder. B. The two outer screws should
be screwed into a wall stud, and the center screw into a drywall anchor. C. If only one stud is
available, the center screw MUST be screwed directly into it, and the two outer screws may be
screwed into the drywall anchors. D. Mark the hole locations with a pencil. The holes should be 4”
(10.15 cm) apart, and level. The minimum height from the surface below must be 19.7” (50 cm).
AVOID INJURY and DAMAGE! The center screw must be screwed directly into a wall
stud. The two additional screws may be screwed into the drywall anchors.
C
C
C
STEP 3. Drill a pilot hole into each mark using a 1/4” wood drill bit for the drywall anchors, and a
1/16” wood drill bit for the wall studs. With a hammer, tap the drywall anchor(s) (C) carefully into
the hole(s) until they are flush with the drywall surface. Use care to avoid damaging the drywall with
the hammer.
7
Page 8
E E
B
B
B
STEP 4. Align the holes in the wall bracket with the pilot holes and drywall anchors. Thread three
wood screws (B) through the holes in the wall bracket and directly into the wall studs and drywall
anchor(s). Make sure the bracket is level. Tighten all screws securely with a screwdriver.
ALWAYS unplug this fireplace heater before assembly or cleaning, or before
relocating. Failure to do so could result in electric shock, fire,orpersonal injury.
B
B
B
8
Page 9
NOTE: We recommend that two capable adults perform this procedure.
STEP 5A. With the help of a capable adult, lift the fireplace and align the two hooks on the back of
the fireplace with the slots on the wall bracket. Carefully set the hooks into the slots.
STEP 5B. Secure the fireplace to the wall bracket with two metal screws , one on each side.
Thread the screws through the fireplace and into the wall bracket side tabs. Tighten both screws
with a Phillips screwdriver.
9
Page 10
NOTE: We recommend that two capable adult perform this procedure.
STEP 6A. With you or someone holding the glass panel, remove the two screws at the top edge of
the fireplace with a Phillips (+) screwdriver.
STEP 6B. Together, carefully remove the front glass panel and set it aside on a clean soft surface.
STEP 6C. Align the tabs of the glass panel with the holes on the top edge of the fireplace. Thread
the screws back into the holes and tighten them both with a Phillips screwdriver.
10
Page 11
Operation
Read and understand this entire owner’s manual, including all safety information,
before plugging in or using this product. Failure to do so could result in electric shock,
fire, serious injury, or death.
Methods of Operation
This electric fireplace can be operated by the touch PANEL, located on the right side panel of the
fireplace (see figure below), or by the battery-powered REMOTE CONTROL.
Before operating, please review the IMPORTANT SAFETY INFORMATION on Pages 2 and 3, and
heed all warnings.
OPERATING TOUCH DISPLAY PANEL AND REMOTE CONTROL
BUTTON
POWER
TIMER
COLOR
FUNCTION
ACTION & INDICATION
Turns the appliance ON/OFF.
TIMER button: Controls timer settings to turn off fireplace at selected time.
Settings range from 0.5 hours to 8 hours.
COLOR button: Makes the color flame effect changing.
NOTE: color effect stays on until power button is turned off. Color flame effect must
be on for heater to turn on.
11
Page 12
FLAME
HEATER
FLAME button: Makes the flame effect dimmer and brighter
NOTE: Flame effect stays on until power button is turned off. Flame effect must be on
for heater to turn
HEATER button: Turns heater on and off.
NOTE: The heater only works when the flame effect is on. If the flame effect is off,
the heater will not turn on.
NOTE: To prevent overheating, the heater blows cool air for 10 seconds
1. Press once: Touch panel indicator becomes active.
2. Press again until desired setting is reached. Digital display shows setting circles as
belows.
Temperature
Backlits
NOTICE
NOTICE
NOTE: Press the button for 5 seconds to switch between °C and °F
BACKLITS button: Changes the colour of back lights
NOTE: Back lights stay on until power button is turned off.
NOTE: Press for 5 seconds to turn off the the backlits.
When the heater is first turned on, a slight odor may be present. This is normal and
should not occur again unless the heater is not used for a long period of time.
To improve operation, aim the remote control at the front of the fireplace. DO NOT
press the buttons too quickly. Give the unit time to respond to each command.
12
Page 13
Temperature Limiting Control
This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe
temperature , the heater will automatically turn OFF. To reset:
1. Unplug the power cord from the outlet.
2. Turn the ON/OFF switch on the CONTROL PANEL to OFF.
3. Wait 5 minutes.
4. Inspect the fireplace to make sure no vents are blocked, or clogged with dust or lint. If they are,
use a vacuum to clean the vent areas.
5. With the POWER switch in the OFF position, plug the power cord back into the outlet.
6. If the problem continues, have your outlet and wiring inspected by a professional.
Remote Control Battery Information
This remote control uses CR2025 batteries (included)
Instructions for battery installation are on the Remote Control battery compartment.
NEVER dispose of batteries in fire. Failure to observe this precaution may result in an
explosion. Dispose of batteries at your local hazardous material processing center.
Care and Maintenance
Cleaning
ALWAYS turn the heater OFF and unplug the power cord from the outlet before
cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in
electric shock, fire, or personal injury.
NEVER immerse in water or spray with water. Doing so could result in electric shock,
fire, or personal injury.
Metal:
Buff using a soft cloth, slightly dampened with a citrus oil-based product.
DO NOT use brass polish or household cleaners as these products will damage the metal trim.
Glass:
Use a good quality glass cleaner sprayed onto the cloth or towel. Dry thoroughly with a paper
towel or lint-free cloth.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
Vents:
Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
Plastic:
Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
13
Page 14
Maintenance
Risk of electric shock! DO NOT OPEN any panels other than the bulb replacement
plate! No user-serviceable parts inside!
ALWAYS turn the heater OFF and unplug the power cord from the outlet before
cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in
electric shock, fire, or personal injury.
Electrical and Moving Parts:
The fan motors are lubricated at the factory and will not require lubrication.
Electrical components are integrated in the fireplace and are not serviceable by the consumer.
Storage:
Store heater in a clean dry place when not in use.
14
Loading...