Page 1
INSTALLATION INSTRUCTIONS
Part List
Please lay out and take an inventory of all parts prior to assembly. Please give us a call if you are missing any parts. Read the
instructions in their entirety prior to beginning assembly and installation. Note: this shade must be installed into wood studs. If
woods studs are not available, anchoring hardware must be used (not included).
Parts in hardware box (parts not shown to scale)
Plug Bracket
(PBNV19) x 1
Crank Bracket
(CBNV19) x 1
Bungee Tie Down
(BUN19) x 2
Parts in pole package (parts not shown to scale)
Pole Screw (x2)
Lock Washer (large =1pcs)
Step 1: Install the Crank Ring
Using the Ring Screw, and Large Lock Washer provided in the pole package, attach the
Ring to the Crank Mechanism (Fig. A).
Screws
(S09 x 6)
Ring (x1) Ring Screw (x1)
(small =2pcs)
Step 2: Determine Your Installation Type
Your shade can be installed against a wall (Fig B) or against
a ceiling/overhang (Fig C). Your shade brackets are prepared
for a wall installation.
If you would like to prepare your shade for a ceiling installation, please see the last page of this manual for help preparing
the brackets.
Wall Installation
Fig. B
Fig. A
Ceiling Installation
Fig. C
Pg. 1
Page 2
Step 3: Mark holes for installation
An installation template has been provided to help position your pilot
holes. To use the template, temporarily attach your template to your
mounting surface (Fig. D ) and drill your pilot holes in the four shaded
areas as shown in Fig. E. Remove the template before moving to the next
step.
Step 4: Install Brackets
Using the provided screws, install the Crank Bracket and Plug Bracket
(Fig F and G). Note: The Crank Bracket should be placed on the right
side of the shade and the Plug Bracket should be placed on the left side
of the shade.
Step 5: Install Shade
To install your shade, start by inserting the Crank Plug into
the Crank Bracket (Fig H).
Next rotate/open the Plug Bracket and insert the shade, making sure to hear a “click” as the pin locks into place (Fig I).
If your shade moves side-to side after installation, we recommend that you adjust the brackets to reduce any lateral
movement between the shade and the brackets.
Fig. D
Fig. F
Fig. H Fig. I
Fig. E
Fig. G
Open Bracket
To reduce lateral movement, roll your shade down and loosen
the screws on both of your brackets slightly. Push the brackets in, (towards each other), to reduce the distance between
the brackets (Fig J).
STEP 6: Assemble Pole
To assemble your pole, slide the Pole-Mid Piece onto the
Pole-Long Piece, making sure the holes are pointing towards
the handle (Fig L). en, slide the Pole-Handle Piece into the
Pole-Mid Piece .
Insert the Pole Screws into the Pole-Mid Piece and completely
tighten (these screws are located in your pole package). Note:
Not all of the Pole-Long Piece is shown in (Fig L).
To use the pole simply insert the hook into the Ring and turn
the Pole-Handle Piece.
Pg. 2
Push brackets in to
reduce slack
Fig. J
Fig L
Page 3
Install Bungee System (optional step)
The shade includes two (2) Bungee Tie Downs to secure the bottom of both sides
of your shade. To install the Bungee System, start by feeding the Bungee through
the Bottom Tube Plugs located at each end of your Bottom Tube (Fig. K). Then
insert the Bungee into the Hook and drill the Hook into a wall/post using one (1)
Bracket Screw from your hardware box. To prevent fabric stretching/damage,
hooks should be installed directly underneath the Bottom Tube Plugs so there is
equal tension on each bungee.
Important: Your shade should be rolled up during windy conditions. The Bungee
System is only eective in light wind. When using your shade, we recommend
leaving at least one (1) roll of fabric wrapped around the top tube.
Additional Optional Steps
Figure K
CHANGING INST
ALLATION TYPE (optional step)
By default, your shade is prepared for a wall installation (Fig M) and comes with
the Crank Bracket on the right side of the shade. If you require a ceiling installation
you will need to make a few small changes to your brackets.
To change your brackets, begin by removing your bracket covers (Fig N).
Remove the 2 screws from the Crank Bracket (Fig O) and the 3 screws from the
Plug Bracket (Fig P).
After removing the screws from both brackets rotate the hardware to match desired
installation conguration (Fig Q).
Fig. N
Fig. O
Fig. P
Wall Installation
Fig. M
Fig. Q
Ceiling Installation
Pg. 3
Page 4
CHANGE THE ROLL DIRECTION OF YOUR SHADE
The default fabric roll direction of your shade is “reverse”. That is, the fabric rolls from the back side of the top tube. If you want
the fabric to roll from the front side of the top tube, simply roll your shade down until it rolls itself back up on the other side of the
shade. If you reverse the roll of your fabric, you will need to move the Ring so it does not interfere with the fabric (see below).
MOVING THE RING FROM THE FRONT TO THE BACK OF THE SHADE
The default placement for your Ring is in the front of your shade. That is, the Ring is
placed near the front of the fabric roll. If you reversed the roll of your fabric, we recommend that you change the location of your Ring.
Before you begin, make sure the shade has been removed from the brackets. To begin,
remove your bracket cover from the Crank Mechanism. Then remove the two screws
from the outside of the Crank Mechanism (Fig R). Then, reverse the Ring and re-install
the Screws (Fig S). Now you can re-install the shade.
Fig. R Fig. S
Loading...