Owner’s Manual
DO NOT
Return to store
For help with installation or warranty issues
call
+1 725 726 4267 / +1 725 726 4227 or
www.symphony-us.com
For parts Visit our secure website
www.symphony-us.com
MOVIL 80
Please keep this important manual in a safe place. It is the owner’s responsibility to
ensure that regular maintenance is carried out on this evaporative cooling product.
Failure to do so will void all guarantees beyond statutory and legal requirements.
Symphony Cooler
Introduction
GENERAL INFORMATION
Thank you for purchasing a quality Symphony Evaporative Cooler. We care about your safety and would
ask you to spend a few minutes reading these simple instructions before installing or operating this
product.
Safety!
Read carefully all of these instructions prior to installing
and operating the unit.
• Read and Save these Instructions.
Do not throw these Instructions away.
• Complete the unit assembly before attempting to install, refer to pages 7-8.
• Installation of this cooler in any manner not prescribed by these instructions could cause a safety
issue and WILL avoid any warranty.
• Use only with a 110 - 120 V~ 60 Hz single phase grounded outlet.
• Do not operate cooler with Rear and Side Filter Panels removed.
• Do not operate cooler with a damaged cord, plug or other component.
• Do not run the power cord under carpet or other floor covering.
• Do not use the power cord with an adaptor plug that converts the 3 pin plug into a 2 prong connector.
• Do not use the cooler with an improperly grounded outlet.
• Do not alter or modify this cooler.
• Do not allow children to install, operate or service this cooler.
• WARNING: To reduce the risk of fire or electric shock, do not use this product with any solid state
speed control device.
• Use only qualified electricians for replacement or servicing of switches, or electrical motors and
components in this cooler.
• Unplug the cooler and press the Motor switch to the OFF position when installing, servicing or cleaning.
• Stagnant water may cause bacterial growth and serious health problems. Do not allow
stagnant water to remain in the tank.
• Drain and clean the water tank before storage, after seasonal use and whenever the unit is not in daily
use.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock,
this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
Page
2
Symphony Cooler
Table of Contents
Introduction ............................................................................................................................................................... 2
Operation Instructions ........................................................................................................................................... 4
General .................................................................................................................................................................. 4
Introduction ................................................................................................................................ ...................... 4
How does your Evaporative Cooler work? ......................................................................... 4
Best Performance locations ................................................................................................ 4
Product Specifications ........................................................................................................ 6
Installation ................................................................................................................................................................. 7
Installation Requirements ................................................................................................................................ 7
Unit Casters Installation ................................................................................................................................... 7
Water Connection ............................................................................................................................................... 9
Before Startup ................................................................................................................................................... 10
Operating the unit .............................................................................................................................................. 6
Maintenance ........................................................................................................................................................... 12
General ................................................................................................................................................................ 12
Filter Pads ...................................................................................................................................................... 12
Water Tank .................................................................................................................................................... 12
Water Distributor .......................................................................................................................................... 12
Motor and Blower Wheel ............................................................................................................................ 12
Pump Operation ............................................................................................................................................ 12
Electrical ........................................................................................................................................................... 13
End of Season ................................................................................................................................................ 13
5 Year Maintenance Planner ..................................................................................................................... 14
Problem Solving .................................................................................................................................................... 15
Warranty .................................................................................................................................................................. 16
Page
3
Symphony Cooler
Operation Instructions
General
Introduction
Your evaporative air conditioner is engineered to meet the rigors of harsh environments. Used and
maintained in accordance with this manual, it will provide you with years of quiet, cool and
environmentally friendly operation. Please take the time to read this manual.
How does your Evaporative Cooler work ?
Warm air is drawn into the evaporative cooler and enter to High Efficiency filters. Water is pumped to
efficiency filters using a submersible pump, warm air is washed through the efficiency filter pads
(absorbing the heat) to provide cool fresh air, blower wheels send the cooled air into room, the warm
stale air within the room is forced out by the cool air throught open doors or windows.
Evaporative cooler produces fresh air eficienctly and inexpensively.
Please Note: This is not an Air conditioner.
Best Performance Location
Indoors
To maximize efficiency, place your Evaporative Cooler in front of an open window, leave another
open window or open door in the opposite to exhaust the warm air. The maximum cooling effect is
felt when a person is near the flow of air produced by the Evaporative Cooler.
Page
4
Symphony Cooler
Operation Instructions
It is essential for successful operation of the evaporative cooler that there be sufficient free air openings in
the room to be cooled – approximately 0.5m² (5.4² feet). Open doors and windows will usually provide this
as per the diagrams below.
Please Note: - It is important for good ventilation that doors or windows are not open on the windward side
of the house. Please note the room furthest away from the cooler needs to have more ventilation than
rooms closest to the cooler.
Outdoors (for outdoor models only)
Use only on GFCI protected outlets/sockets (for USA only). Press the TEST button (then RESET
button) every month to ensure proper operation.
Power cords must be secured to avoid tripping.
The wiring and connections must be protected from water. Electrical plug and Evaporative cooler
connections must be dry at all times. When used outdoors, insert the air cooler electrical plug
into an IP44compliant outdoor electrical outlet.
Set the unit on a solid surface, not recommended to be placed outdoors during heavy rain or
snow.
Page 5
Symphony Cooler
Operation Instructions
Product Specifications
Page
6
MODEL
MOVIL 80
Voltage
120 VAC, 60 Hz, 1 Phase
Amperage
1.8 A
Tank Capacity
21 Gallons (80 Lts)
Net Weight
19 Kg
Unit Dimensions
Assembled
(H X W X D)
45 in X 24 in X 19.68 in
Drain Plug
Symphony Cooler
Installation
Installation Requirements
Tools
• Cordless Screwdriver
• PH2 bits
• Phillips Head Screw Driver
Materials Required (Not supplied)
• Sillcock Valve - for water line connection to faucet (see pg. 9)
Unit Casters Installation
Please follow the instructions for a correct product assembly.
DO NOT connect the power to the cooler until the installation is complete.
• Remove the product from the packaging.
• Locate the Casters kit.
• Insert the Casters Block Raisers into the bottom of the equipment.
• For Assemble, use the 10 screws (8 X 19 mm) included in the casters kit.
Page
7
Symphony Cooler
Installation
Page
8
Introduce the screws into the holes of each
block raisers and fit.
Ensure that the Caster block raisers are fixed
rigidly to the water tank of cooler
Symphony Cooler
Installation
Water Connection
Install a sillcock (not supplied) to the faucet closest to the
cooler.
Using a Spout bucket or plastic hose, add clean water
into the water inlets, to tank. Check the water level
indicator on the Right Side of water tank to see when the
water tank is full.
Your cooler is now ready for startup checklist (see next page).
Page 9
Symphony Cooler
Installation
Before Startup
• Check that another door or window in the room is open to allow air to exhaust to other parts of the
house.
• Ensure that the filters are kept clean.
• Ensure that the water tank is filled with clean water (at least 5 gallons or 20 liters).
• Plug the cooler into a 110 V - 120 V~ 60 Hz single phase grounded appliance socket on the inside
of the house and switch the socket on.
• Press the COOL button to on the water pump.
• Press the Speeds buttons and check the operation of the three speeds motor.
• Leaving the unit in the COOL mode for 15 minutes, you may notice a wet paper smell as the water
circulates around the filter pads. This is normal during the commissioning phase and at the beginning of
each season when the unit is operated after the winter break. It will only last for a short time.
• Drain completely water tank removing drain plug and refill again the water tank to water level
desired.
• Do not add any chemical odor enhancers or liquid detergent of any kind to the tank.
• IMPORTANT. After the first 10 hours of operation in COOL mode, the water must be drained from
the unit water tank to remove any new product residuals. This process must be repeated after a
further 10 hours of COOL mode operation. (See page 12 for removing the Drain Plug). To clean
the tank you must only remove the Drain Plug.
Page
10
Symphony Cooler
Operation Instructions
Operating the unit
This Symphony cooler is only operated in Manual mode. This is selectable by pressing switches on the front
panel. COOL, SWING and MOTOR functions are available.
Manual Mode:
1
1 Motor OFF
2 Motor Speeds
3 COOL
4 Vertical Swing
1. Motor OFF : Stop Motor Operation
2. Motor Speeds: Press Motor Speed button, High , Med or Low, according to your comfort.
3. COOL: Press Cool button to start Water pump function, release the button to stop operation.
4. Vertical swing: Press Swing button to start Air Oscillation function, release the button to stop operation.
Page 11
Symphony Cooler
Maintenance
Before starting any maintenance work on your unit, ensure it is disconnected
from the power supply.
Note: It is essential that your evaporative air conditioner is maintained in accordance with this manual.
Fai-lure to do so will affect the life of the product and reduce the level of efficiency.
THIS MANUAL CONTAINS A 5 YEAR MAINTENANCE PLANNER TO USE IN CONJUNCTION WITH
THE-SE INSTRUCTIONS. See page 14.
Remove Rear and Side Filter Panels fixing screws (12 off).
General
Filter Pads
Visually check Filter pad for damage or blockage. Gently hose down pad from both sides to remove any
build up of salts, dust and pollen. In dusty areas more regular cleaning is recommended. Check the water
distributor, making sure it is clear and free from blockage. Failure to do so may lead to uneven water
distribution and therefore less efficient operation.
Water Tank
It is important to keep the water tank clean and free from sediment and algae growth. Using a small soft
bristle brush, brush all surfaces in the tank while it is full of water . Turn off the water inlet to the unit (an
isolation valve should be fitted to the water inlet before the float valve or at the water supply faucet). Drain
the tank by removing the drain plug and afterwards replace the drain plug and open the water valve. After
refilling, it may be necessary to repeat this procedure if the tank is very dirty.
Water Distributor
Check the water distribution system for blockage in top.
Motor and Blower Wheel
Check that the blower wheel spins freely. Check the motor for corrosion and spray with an anti-corrosive
agent if necessary.
Pump Operation
Check the pump spins freely and that the strainer is clean.
After a long idle period, the pump may stop rotating due to a mineral build up on the stainless shaft
adjacent to the motor. To free the pump shaft, remove mineral build up and rotate the shaft using fingers
or suitable sized pliers.
Spraying the area with suitable water displacement lubricate (such as WD-40®) may assist
Page
12
Symphony Cooler
Maintenance
Electrical
No general maintenance is required to the electrical system.
Electrical connections and maintenance should only be carried out by a qualified
electrician.
End of Season
If the Evaporative Cooler will not be used for a long time:
• Make sure all parts are dry by running nly the Motor during 2 hours before storing (time
depends on ambient humidity conditions)
• Switch OFF the Motor and unplug the evaporative cooler from the power supply
• Drain all the water from tank, remove the Side Pads and clean the water tank with a damp
cloth to wipe away any dust or mineral deposits finally replace the Side Pads.
• To protect model from dust, moisture or scratches, cover with a clean cloth, tarp or plastic
bag before storing.
• Roll the power cord and store it away from the floor to protect it.
• Store this model at room temperature in a dry location, away from direct sunlight and/or very
hot, cold or damp environments.
Page
13
Symphony Cooler
Maintenance
5 Year Maintenance Planner
1st
2nd
3rd
4th
5th
Year
Year
Year
Year
Year
1.1
Check quality of filters
PRESEASON
1.2
Check Motor & pump
1.3
Fill unit with water
CHECK
1.4
Start unit
FIRST
2.1
Check and clean filters
2.2
Drain, clean and refill water tray
MIDSEASON
2.3
Check strainers and filters
SERVICE
2.4
Check unit operates correctly
SECOND
3.1
Check and clean filters
3.2
Drain, clean and refill water tray
MIDSEASON
3.3
Check strainers and filters
SERVICE
3.4
Check unit operates correctly
END OF SEASON
4.1
Turn off water supply
4.2
Drain and clean unit
SERVICE AND
4.3
Leave Drain plug removed
SHUT DOWN
4.4
Check motor and pump and
spray with a water
displacement lubricant
To Order Parts
www.symphony-us.com
For Technical Advice/Warranties
+1-725-726-4267
+1-725-726-4227
Page
14
Symphony Cooler
Problem Solving
PROBLEM
PROBABLE CAUSE
REMEDY
Unit fails to start
a
Power Failure
a
Wait for power to be turned on
b
Tripped Circuit Breaker
b
Reset circuit breaker
c
Blown fuse
c
Replace
d
Electrical Fault
d
Call Symphony Care Line
e
Motor Failure
e
Change the motor
Filter Pads not
wetting
a
Not enought Water in Tank
a
Add clean water in tank
(at least 5 Gallons / 20 Liters)
b
Pump failure
b
See Maintenance page- Pump section
/ Replace water Pump
Filter Pads too
wet
c
Electrical Fault with pump
c
See Maintenance page- Pump section
/ Replace water Pump
Water leaking from
Overflow holes
a
Water level exceeded in water
tank
a
Close the water input valve
b
Drain some water in tank
Water Droplets in air
stream
a
Loose Pump pipe
a
Check and tighten
b
Break in hose
b
Replace as necessary
c
Pump appears to deliver excessive
water to pads
c
Check the condition of the filter pad.
Wash if pad shows heavy buildup of
minerals
Excessive humidity
a
Not enought air flow
a
Increase Fan speed
b
Inadequate Exhaust
b
Provide more open area to exhaus stale air
by opening windows and doors in adjacent
rooms.
Inadequate Cooling
a
Dirty Filters
a
Clean Filters
b
Dry Filters
b
Check control set on COOL Mode.
Check water delivery system.
Adjust if necessary.
Unpleasant Odor
a
Unit located near odor source
a
Remove source
b
Algae in water tank
b
Clean tank and refill with fresh water
ANY FURTHER PROBLEMS PLEASE CONTACT YOUR
SYMPHONY CUSTOMER CARE LINE
Page
15
Symphony Cooler
Warranty
Condition of Warranty (U.S.A.)
We extend this limited warranty to the original buyer (first retail purchaser) and warranty that the product
shall be free from manufacturer defects in workmanship and materials for 12 months from the date of
purchase.
A. Warranty will come in with effect when following conditions are met with:
a) Warranty registration card duly filled and received by the company within 10 days from the date of
purchase.
b) Product is operated following the recommendations explained inside the user manual.
B. The company´s liability under the warranty will be limited only to motor, pump, louver motor, remote, PCB
and also restricted to any such defect which occurs under conditions of normal operations and under proper
use. Any part/s replaced by the company at its discretion shall be a functionally operative unit.
C. This warranty shall not apply to product:
1) Which have not been purchased from authorized distributor through their network or company´s
authorized retail stores.
2) Which have been altered/opened by any other personnel not authorized by the company.
3) Incorrectly used in combination with any other substance or products.
4) Which are used for commercial rental purpose and/ or which develops problems due to faulty care or
maintenance and alterations to product or its parts.
5) Which us subjected to electrical supply for which the product is not designed.
6) Warranty will void if the product is operated with a sub-standard inverter or non-sine wave inverter.
7) If documentation of buying is not available to validate an original purchase.
D. While the company will make every effort to carry out the repairs at the earliest, it however is made
expressly clear that the company is under no obligation to do so in a specified period of time.
E. This warranty shall automatically terminated on expiry of the warranty period of 12 months from the date
of purchase even if the product may not be used for any time during the warranty period for any reason
whatsoever.
F. Cooling pads and outer plastic parts are not covered under warranty.
G. The company shall not be liable in any case for any loss or damage caused to any property , death or
disability caused to any human life arising out of fire, electrical fault, short circuit, accidental handling or any
kind of natural calamity. As, such the company´s liability is limited to the cost of the spare parts of the said
products only.
H. Change of address of the costumers must be intimated to the company without which the warranty shall
not be operational.
I. Due to ongoing research and development , the company holds the rights to modify the product without
any prior notice or obligation to buyers.
J. Purchaser should retain the purchase bill as evidence of the date of purchase. Copy of the purchase
invoice should be given to the visiting service technician while attending the complaint. In case of any
alteration in the date of purchase invoice is found without sign and seal of the dealer, the warranty shall be
void.
K. During the warranty, costumer is not entitled for exchange of product or refund money.
L. The company does not have any Annual Maintenance Contract (AMC) policy.
M. Warranty will be applicable if registered within 21 days of purchase.
Warranty Period
Product Model
Parts
MOVIL 80
12 Months
Page
16
Loading...