Symphonic ST420FF User Manual

FEATURES

●

MTS/SAP Tuner

●

Flat Screen Picture Tube

●

181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.

●

PLL Frequency Synthesized Tuning- Provides free and easy channel selection and lets
you tune directly to any channel using the channel number buttons on the remote control.

●

Sleep Timer

●

Closed Caption Decoder

●

Auto Shut Off Function- If there is no signal input from the antenna terminal and no user
operation for 15 minutes, the TV will turn itself off automatically.

●

Resume Function- If the power fails or is disconnected while the TV is on, the TV will turn
on automatically when the power resumes.

●

V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.

●

Full-Function Remote Control

●

On-Screen Function Display

●

S-VIDEO Input- Allows you to get better picture detail and clarity.

●

Front AV Input

●

Rear Audio Input

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con­nected to the grounding system of the building as close to the point of cable entry as practical.

FCC WARNING- This equipment may
generate or use radio frequency energy.
Changes or modifications to this equip­ment may cause harmful interference
unless the modifications are expressly
approved in the instruction manual.
The user could lose the authority to
operate this equipment if an unautho­rized change or modification is made.

Owner’s Manual

1EMN20969 Printed in Malaysia

L3355UF * * * * *

ST420FF

20 INCH COLOR TELEVISION

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI­ANCE TO RAIN OR MOISTURE.

IMPORTANT SAFEGUARDS

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK) NO
USER SERVICEABLE PARTS INSIDE. REFER SER­VICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

THIS SYMBOL INDICATES THAT DAN­GEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRE­SENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT
THERE ARE IMPORTANT OPERATING
AND MAINTENANCE INSTRUCTIONS
IN THE LITERATURE ACCOMPANYING
THE APPLIANCE.

The important note is located on the rear of the cabinet.

1. READ INSTRUCTIONS - All the safety and operating
instructions should be read before the appliance is
operated.

2. RETAIN INSTRUCTIONS - The safety and operating
instructions should be retained for future reference.

3. HEED WARNINGS - All warnings on the appliance
and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS - All operating and use
instructions should be followed.

5. CLEANING - Unplug TV from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol clean­ers. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupt­ed service and, that for some specific reason, such as
the possibility of the loss of an authorization code for a
CATV converter, is not intended to be unplugged by
the user for cleaning or any other purpose, may
exclude the reference to unplugging the appliance in
the cleaning description otherwise required in item 5.

6. ATTACHMENTS - Do not use attachments not recom­mended by the TV manufacturer as they may cause
hazards.

7. WATER AND MOISTURE - Do not use this TV near
water, for example, near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool, and the like.

8. ACCESSORIES - Do not place this
TV on an unstable cart, stand, tripod,
bracket, or table. The TV may fall,
causing serious injury to someone, and
serious damage to the appliance. Use
only with a cart, stand, tripod, bracket,
or table recommended by the manufac­turer, or sold with the TV.
Any mounting of the appliance should follow the man­ufacturer’s instructions and should use a mounting
accessory recommended by the manufacturer. An appli­ance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the appliance and cart combination to overturn.

AMEUBLES - Cet appareil ne doit
être placé que sur un meuble (avec
ou sans roulettes) recommandé par
le fabricant. Si vous l’installez sur
un meuble à roulettes, déplacez les
deux ensembles avec précaution. Un
arrêt brusque, l’utilisation d’une
force excessive et des surfaces irrégulières risquent de
déstabiliser l’ensemble et de le renverser.

9. VENTILATION - Slots and openings in the cabinet and
the back or bottom are provided for ventilation and to
ensure reliable operation of the TV and to protect it
from overheating, these openings must not be blocked
or covered. The openings should never be blocked by
placing the TV on a bed, sofa, rug, or other similar sur­face. This TV should never be placed near or over a
radiator or heat register. This TV should not be placed
in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufactur­er’s instructions have been adhered to.

10. POWER SOURCES - This TV should be operated only
from the type of power source indicated on the mark­ing label. If you are not sure of the type of power sup­ply to your home, consult your appliance dealer or
local power company. For TVs intended to operate
from battery power, or other sources, refer to the oper­ating instructions.

11. GROUNDING OR POLARIZATION - This TV is
equipped with a polarized alternating-current line
plug(a plug having one blade wider than the other).
This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.

12. POWER-CORD PROTECTION - Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, con­venience receptacles, and the point where they exit
from the appliance.

13. OUTDOOR ANTENNA GROUNDING - If an outside
antenna or cable system is connected to the TV, be sure
the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up stat­ic charges. Article 810 of the National Electrical Code,
ANSI/NFPANo. 70, provides information with respect
to proper grounding of the mast and supporting struc­ture, grounding of the lead-in wire to an antenna dis­charge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding elec­trodes, and requirements for the grounding electrode.
(Fig. A)

14. LIGHTNING - For added protection for this TV
receiver during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug
it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the TV due
to lightning and power-line surges.

15. POWER LINES - An outside antenna system should
not be located in the vicinity of overhead power lines
or other electric light of power circuits, or where it can
fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be
taken to keep from touching such power lines or cir­cuits as contact with them might be fatal.

16. OVERLOADING - Do not overload wall outlets and
extension cords as this can result in a risk of fire or
electric shock.

17. OBJECT AND LIQUID ENTRY - Never push objects
of any kind into this TV through openings as they may
touch dangerous voltage points or short out parts that
could result in a fire or electric shock. Never spill liq­uid of any kind on the TV.

18. SERVICING - Do not attempt to service this TV your­self as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.

19. DAMAGE REQUIRING SERVICE - Unplug this TV
from the wall outlet and refer servicing to qualified
service personnel under the following conditions:

a. When the power supply cord or plug is damaged or

frayed.

b. If liquid has been spilled, or objects have fallen into

the TV.

c. If the TV has been exposed to rain or water.
d. If the TV does not operate normally by following the

operating instructions. Adjust only those controls that
are covered by the operating instructions, as improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified techni­cian to restore the TV to its normal operation.

e. If the TV has been dropped or damaged in any way.
f. When the TV exhibits a distinct change in performance,

this indicates a need for service.

20. REPLACEMENT PARTS - When replacement parts
are required, be sure the service technician uses
replacement parts specified by the manufacturer that
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, injury to persons or other hazards.

21. SAFETY CHECK - Upon completion of any service or
repairs to this TV, ask the service technician to perform
routine safety checks to determine that the TV is in
proper operating condition.

22. HEAT - This TV product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ELECTRIC
SERVICE
EQUIPMENT

GROUND
CLAMP

NEC - NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING

ELECTRODE SYSTEM
(NEC ART 250, PART H)

S2898A

GROUND CLAMPS

GROUNDING CONDUCTORS
(NEC SECTION 810-21)

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

ANTENNA
LEAD IN
WIRE

PRECAUTIONS

●

Place your TV in a room with adequate ventilation.

●

Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.

●

Do not place your TV on soft surfaces, such as rugs or blankets.

●

Leave enough room for air to circulate around the bottom, top and back of the set.

The serial number of this product may be found on the back of the TV. No others have the same
serial number as yours. You should record the number and other vital information here and retain
this book as a permanent record of your purchase to aid identification in case of theft.

IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING
AFTER READING OWNER’S MANUAL, PLEASE CALL

TOLL FREE

1-800-242-7158

OR VISIT OUR WEB SITE AT http://www.Symphonic.us.

FUNAI CORPORATION

LIMITED WARRANTY

FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:

DURATION:

PAR TS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from

the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded
from this warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date

of original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail pur­chase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or
if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does not
apply to any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does
not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not sup­plied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alter­ation, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or
damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN
THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE
CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SER­VICE CENTER.

THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT.
IF NO PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS
COSTS WILL BE CHARGED.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT
VA RY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE
TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.

To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries,
please contact us at :

FUNAI CORPORATION

Customer Service

Tel :[phone]

http://www.Symphonic.us

19900 Van Ness Avenue, Torrance, CA 90501

Date of Purchase
Dealer Purchase from
Dealer Address

Dealer Phone No.
Model No.
Serial No.

PORTABLE CART WARNING

S3126A

SYMBOLE D'AVERTISSEMENT POUR

LES COMPOSANTES

APPAREIL ET MEUBLE A ROULETTES

S3126A

This function allows you to shut off the power automatically in a certain amount of time.

1) Press

[POWER] to turn on the TV and press [SLEEP].

2) Within 10 seconds, press [SLEEP] repeatedly to change an amount of
time. Each time [SLEEP] is pressed, the time increases by 10 minutes
up to 90 minutes.

INSTALLING THE BATTERIES

Install two AA batteries (supplied)
matching the polarity indicated inside
battery compartment of the remote con­trol.

[BATTERY PRECAUTIONS]

• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.

• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.

• If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.

• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.

PREPARATION FOR USE

2

1

3

CONNECTIONS

VIDEO1 input (Rear)

ANT.IN

S-VIDEO

AUDIO IN

R

L

SELECTING AUDIO/VIDEO INPUT

When you use the AUDIO/VIDEO input jacks, select “VIDEO1” or “VIDEO2” mode by pressing
[INPUT SELECT] on the remote control. The input mode changes by pressing the button as fol­lowing:

•To use the jacks on the rear of the TV, select “VIDEO1”.

•To use the jacks on the front of the TV, select “VIDEO2”.

TV channel VIDEO1 (Rear) VIDEO2 (Front)

OPERATIONS

VIDEO2 input (Front)

VIDEO

AUDIO RL

SLEEP TIMER SETTING

Note:

●

If some digits appear in the corner of the screen when the unit is turned on at the first time,
press

[POWER] without unplugging the power cord.

Audio Cable

S-Video Cable

Video Cassette Recorder

Note:

●

The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for
connecting monaural audio equipment.

Video Cable

Audio Cable

Video GameVideo Camera

Front of this TV

Rear of this TV

Note:

●

The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for
connecting monaural audio equipment.

REMOTE CONTROL AND FRONT PANEL FUNCTION

123

456

789

0 +100

DISPLAY

VOL

CH

CH

VOL

SLEEP

CHANNEL

RETURN

INPUT

SELECT

MUTE

GAME

POWER

MENU

POWER button

To turn TV on/off

Channel number buttons

CH ▲ /▼ buttons

MENU button

To view on-screen menu

GAME button
SLEEP button

DISPLAY button

To display CH No./Audio Status

CHANNEL RETURN button

To return to previous channel

INPUT SELECT button

To select TV or external input

MUTE button

VOL ▲ /▼ buttons

To select channels

To adjust volume

VIDEO L - AUDIO - R

MENU

Y

VOLUME XL CHANNEL

K

HEADPHONE

POWER

VIDEO L - AUDIO - R

MENU

Y VOLUME XL CHANNEL K

HEADPHONE

POWER

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.

[EXTERNAL CONNECTION]

ex.

ex.

Infrared Sensor Window

POWER button

To turn TV on/off

CHANNEL ▲ /▼ buttons

To select channels

VOLUME XX/YYbuttons

To adjust volume

MENU button

To view on-screen menu

HEADPHONE jack

AUDIO L/R input jacks

VIDEO input jack

Note:

●

For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. IN
jack before moving the unit.

(IN)

(OUT)

(OUT)

(IN)

(OUT)

(IN)

(IN)

(OUT)

Notes:

●

When you disconnect the unit from the AC outlet or when you have a power failure, the sleep
time will be lost.

●

To cancel the sleep timer, press [SLEEP] repeatedly until “SLEEP 0” is displayed.

●

The Sleep Timer Setting display will disappear automatically after 10 seconds of the operation.

SLEEP 10

ANT. IN

IN

OUT

Plug the incoming cable into the ANT. IN jack on the rear of the TV.

*Note (DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled signals and
require a special converter to receive these channels.
Consult your local cable company.

OR

Incoming cable from home Antenna /
Cable Company (No Cable Box)

Incoming cable from Cable
Company or Satellite Antenna

Cable Box or
Satellite Box*

Cable

TV signal

Antenna

UHF/VHF Rod Antenna

(Not supplied)

Rear of this TV

OR

You may view specially labeled (cc) TV programs, movies, news and prerecorded tapes, etc. with
either a dialogue caption or text display added to the program.

1) Press

[MENU]. Use [CH ▲ /▼] to point to “CAPTION”.

2) Use

[VOL ▲/▼] to select the mode you wish.

The CAPTION mode will be changed by pressing the button as following:

3) When done, press [MENU] to exit the menu.

[AUTO PRESET CHANNELS]

As the initial setting, this TV has memorized all channels, including the ones not available in your
area. This feature automatically puts only available channels into the memory.

1) Press

[MENU]. Using [CH ▲ /▼] select “CHANNEL SET”, then press

[VOL ▲].

2) Using [CH ▲ /▼] select “AUTO PRESET CH”, then press [VOL ▲].

The tuner scans and memorizes all available channels in your area.

3) When the scanning is completed, the lowest memorized channel appears on the TV screen.

This affects the language of the TV's setup menus and on-screen display terms.

1) Press

[MENU]. Use [CH ▲ /▼] to select “[ENG]”.

2) Use

[VOL ▲/▼] to select “ENG(lish)”, “ESP(añol)” or “FRA(nçais)”.

3) Press [MENU] to exit the menu.

You can adjust the TV’s brightness, contrast, color, tint and sharpness as you prefer.

1) Press

[MENU]. Press [VOL ▲] to select “PICTURE”.

2) Press [CH ▲ /▼] to select an item and press [VOL ▲/▼] to adjust setting.

GAME MODE

Set to the most suitable position for video games.

[-] : OFF [+] : ON

BRIGHT

Adjust until the darkest parts of the picture are as bright as you prefer.

[-] : decrease brightness [+] : increase brightness

CONTRAST

Adjust to increase or decrease contrast.

[-] : decrease contrast [+] : increase contrast

COLOR

Adjust to be brilliant or pale color.

[-] : be pale color [+] : be brilliant color

TINT

Adjust to obtain natural skin tones.

[-] : add red [+] : add green

SHARPNESS

Adjusts the detail of the picture.

[-] : make soft [+] : make clear

You can set to receive TV programs in Stereo, Second Audio or Monaural sound as you prefer.

1) Press

[MENU]. Using [CH ▲ /▼] select “TV SOUND”.

2) Use [VOL ▲/▼] to select [MAIN], [MONO] or [SAP]

(Second Audio Program).
The sound mode will be changed by pressing the button as following:

3) Press [MENU] to exit the menu.

OPERATIONS (Continued)

OPTIONAL SETTINGS

PICTURE ADJUSTMENT

This feature is helpful for playing video games. By pressing [GAME], you can set Game mode
(suitable picture setting for games) and TV selects automatically front A/V input.

1) To use video games;
Press

[GAME].

2) To cancel Game mode only;
Press

[MENU] and [VOL ▲ ] to select “PICTURE”. Then Game mode will

automatically be canceled. (The setting menu will disappear after 10 sec­onds.)

3) To watch another input (game, DVD player, camcoder etc.);
Press

[INPUT SELECT] repeatedly.

CHANNEL SETTING

[ADDING/DELETING CHANNELS]

You can add or delete channels manually.

1) Press [MENU]. Using [CH ▲ /▼] select “CHANNEL SET”, then press [VOL ▲].

2) Press

[VOL ▲] to select “ADD/DELETE”.

3) Use

[CH ▲ /▼] to select the channel you wish to put into memory or to

erase from memory.

4) Use [VOL ▲/▼] to add or delete the channel. The added channel number will appear in light

blue and deleted channel number will appear in light red.

GAME MODE

LANGUAGE SELECTION

[OFF] [C1] [C2] [T1] [T2]

[CAPTION MODE (C1, C2)]

●

CAPTION1 (C1)
displays standard closed captions (what a character is saying).

●

CAPTION2 (C2)
displays foreign language closed captions (foreign language words showing what a character is
saying).

●

There are three ways of displaying according to programs:

Paint-on mode: Displays input characters on the screen immediately.
Pop-on mode : Once characters are stored in memory, they are displayed all at once.
Roll-up mode : Displays the characters continuously by scrolling

(max. 4 lines).

[TEXT MODE (T1, T2)]

●

TEXT1 (T1) and TEXT2 (T2) display half-screen text by scrolling (such as
a channel guide, schedule or announcement).

CLOSED CAPTION

*Second Audio Program (SAP) :

Your program can also be received in a sec­ond language or sometimes a radio station.

MULTI-CHANNEL TELEVISION SOUND (MTS

)

Typ e of

broadcast

Regular

-None-

Stereo

broadcast

STEREO

SAP

Menu

Selection

MAIN

MONO

SAP*

-None- -None-

MONO

STEREO

SAP

MAIN

MAIN

Note:

●

If you select [SAP] when second audio is
not available, the TV will receive normal
audio.

[MAIN] [MONO] [SAP]

PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]

[-]

BRIGHT

[+]

[-]

CONTRAST

[+]

[-]

COLOR

[+]

[-]

TINT

[+] [-]

SHARPNESS

[+]

[-]
OFF

GAME MODE

[+]

ON

Picture: GAME
Input: Front (VIDEO2)

Picture: Customized
Input: Front (VIDEO2)

Notes:

●

If you press [GAME] when the TV is off, the TV turns on and will be in Game mode and
external input mode automatically.

●

If you adjust another picture control while in Game mode, this mode will automatically be can­celed.

Notes:

●

The display will disappear automatically after 10 seconds unless you press any buttons.

●

Magnetism from nearby appliances and speakers might affect the color of the TV picture. If
this happens, press [POWER] to turn off the TV and turn it on again after about 30 minutes.

Notes:

●

If closed captioning is not broadcasted, you cannot receive it and nothing is displayed.

●

When your TV receives a special effects playback signal (i.e., Search, Slow and Still) from a
VCR’s video output channel (CH3 or CH4), the TV may not display the correct caption or text.

●

Captions and texts may not match the TV voice exactly.

●

Interference may cause the closed caption system not to function properly.

●

The caption or text characters will not be displayed while the menu display or functions display
is shown.

●

If a black box appears on the screen, this means that the TV is set to TEXT mode. To clear
screen, select CAPTION [C1], [C2] or [OFF].

Notes:

●

The TV distinguishes between standard TV channels and cable (CATV) channels.

●

The TV may recognize TV channels as CATV channels if reception condition is poor. If this
happens, check the antenna connections and try steps 2) to 3) again when reception conditions
are better.

●

If there is no TV signal input, “NO TV SIGNALS” will appear on the
display after the completion of channel scanning.

Note:

●

The menu will disappear automatically after about 10 seconds.

PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]

ADD/DELETE
AUTO PRESET CH

NO TV SIGNALS

ADD/DELETE
AUTO PRESET CH

GAME

VIDEO2

VIDEO1

PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]

PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]