Symphonic CSL1505 User Manual
FEATURES
●
MTS/SAP Tuner
●
181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.
●
PLL Frequency Synthesized Tuning- Provides free and easy channel selection and lets
you tune directly to any channel using the channel number buttons on the remote control.
●
Sleep Timer
●
Closed Caption Decoder
●
Auto Shut Off Function- If there is no signal input from the antenna terminal and no user
operation for 15 minutes, the TV will turn itself off automatically.
●
V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.
●
Full-Function Remote Control
●
On-Screen Function Display
●
S-VIDEO Input- Allows you to get better picture detail and clarity.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
FCC WARNING - This equipment may
generate or use radio frequency energy.
Changes or modifications to this equipment may cause harmful interference
unless the modifications are expressly
approved in the instruction manual.
The user could lose the authority to
operate this equipment if an unauthorized change or modification is made.
1EMN20672 Printed in China
L3121CM * * * * *
CSL1505
15 INCH LCD TELEVISION
(Photo Stand Type)
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFEGUARDS
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK) NO
USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT
THERE ARE IMPORTANT OPERATING
AND MAINTENANCE INSTRUCTIONS
IN THE LITERATURE ACCOMPANYING
THE APPLIANCE.
The important note is located on the rear of the cabinet.
1. READ INSTRUCTIONS - All the safety and operating
instructions should be read before the appliance is
operated.
2. RETAIN INSTRUCTIONS - The safety and operating
instructions should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance
and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use
instructions should be followed.
5. CLEANING - Unplug TV from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as
the possibility of the loss of an authorization code for a
CATV converter, is not intended to be unplugged by
the user for cleaning or any other purpose, may
exclude the reference to unplugging the appliance in
the cleaning description otherwise required in item 5.
6. ATTACHMENTS - Do not use attachments not recommended by the TV manufacturer as they may cause
hazards.
7. WATER AND MOISTURE - Do not use this TV near
water, for example, near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool, and the like.
8. ACCESSORIES - Do not place this
TV on an unstable cart, stand, tripod,
bracket, or table. The TV may fall,
causing serious injury to someone, and
serious damage to the appliance. Use
only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer, or sold with the TV.
Any mounting of the appliance should follow the manufacturer’s instructions and should use a mounting
accessory recommended by the manufacturer. An appliance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the appliance and cart combination to overturn.
9. VENTILATION - Slots and openings in the cabinet and
the back or bottom are provided for ventilation and to
ensure reliable operation of the TV and to protect it
from overheating, these openings must not be blocked
or covered. The openings should never be blocked by
placing the TV on a bed, sofa, rug, or other similar surface. This TV should never be placed near or over a
radiator or heat register. This TV should not be placed
in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
10. POWER SOURCES - This TV should be operated only
from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or
local power company. For TVs intended to operate
from battery power, or other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION - This TV is
equipped with a polarized alternating-current line
plug(a plug having one blade wider than the other).
This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
12. POWER-CORD PROTECTION - Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit
from the appliance.
13. OUTDOOR ANTENNA GROUNDING - If an outside
antenna or cable system is connected to the TV, be sure
the antenna or cable system is grounded so as to provide some protection against voltage surges and builtup static charges. Article 810 of the National Electrical
Code, ANSI/NFPA No. 70, provides information with
respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode. (Fig. A)
14. LIGHTNING - For added protection for this TV
receiver during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug
it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the TV due
to lightning and power-line surges.
15. POWER LINES - An outside antenna system should
not be located in the vicinity of overhead power lines
or other electric light of power circuits, or where it can
fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be
taken to keep from touching such power lines or circuits as contact with them might be fatal.
16. OVERLOADING - Do not overload wall outlets and
extension cords as this can result in a risk of fire or
electric shock.
17. OBJECT AND LIQUID ENTRY - Never push objects
of any kind into this TV through openings as they may
touch dangerous voltage points or short out parts that
could result in a fire or electric shock. Never spill liquid of any kind on the TV.
18. SERVICING - Do not attempt to service this TV yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
19. DAMAGE REQUIRING SERVICE - Unplug this TV
from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a. When the power supply cord or plug is damaged or
frayed.
b. If liquid has been spilled, or objects have fallen into
the TV.
c. If the TV has been exposed to rain or water.
d. If the TV does not operate normally by following the
operating instructions. Adjust only those controls that
are covered by the operating instructions, as improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the TV to its normal operation.
e. If the TV has been dropped or damaged in any way.
f. When the TV exhibits a distinct change in perfor-
mance, this indicates a need for service.
20. REPLACEMENT PARTS - When replacement parts
are required, be sure the service technician uses
replacement parts specified by the manufacturer that
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, injury to persons or other hazards.
21. SAFETY CHECK - Upon completion of any service or
repairs to this TV, ask the service technician to perform
routine safety checks to determine that the TV is in
proper operating condition.
22. HEAT - This TV product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ELECTRIC
SERVICE
EQUIPMENT
GROUND
CLAMP
NEC - NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
GROUND CLAMPS
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ANTENNA
LEAD IN
WIRE
PRECAUTIONS
●
Place your TV in a room with adequate ventilation.
●
Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.
●
Do not place your TV on soft surfaces, such as rugs or blankets.
●
Leave enough room for air to circulate around the bottom, top and back of the set.
The serial number of this product may be found on the back of the TV. No others have the same
serial number as yours. You should record the number and other vital information here and retain
this book as a permanent record of your purchase to aid identification in case of theft.
Owner’s Manual
IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING
AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE
1-800-242-7158 OR VISIT OUR WEB SITE AT http://www.Symphonic.us
FUNAI CORPORATION
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in CANADA in the event of defect in materials or workmanship as follows:
DURATION :
PAR TS : FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of origi-
nal retail purchase. Certain parts and LCD image burn-in are not covered under this warranty.
LABOR : FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original
retail purchase.
LIMITS AND EXCLUSIONS :
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT
OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE
PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or
if service was attempted by AUTHORIZED SERVICE FACILITY. This FUNAI CORPORATION Limited warranty
does not apply to any product not purchased and used in CANADA.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does
not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or
damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN
CANADA.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE
FACILITY.
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE
FACILITY.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT.
IF NO PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS
COSTS WILL BE CHARGED.
ATTENTION :
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR
NOTICE.
To locate your nearest AUTHORIZED SERVICE CENTER or general service inquiries, please contact us at :
FUNAI CORPORATION
Customer Service
Tel: 1-800-242-7158
http://www.Symphonic.us
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
PORTABLE CART WARNING
S3126A
R
L
VIDEO1
S
-V
I
D
E
O
V
I
D
E
O
A
N
T
H
E
A
D
P
H
O
N
E
A
U
D
I
O
ANT
IN
OUT
INSTALLING THE BATTERIES
Install two AAA batteries (supplied)
matching the polarity indicated inside
battery compartment of the remote control.
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
PREPARATION FOR USE
2
1
3
CONNECTIONS
R
L
S
-
V
ID
E
O
V
I
D
E
O
A
N
T
H
E
A
D
P
H
O
N
E
A
U
D
I
O
VIDE
O
1
R
L
S-VIDEO
VID
EO
ANT
HEAD PHO
NE
VIDEO1
AUDIO
OPERATIONS
Note:
●
If some digits appear in the corner of the screen when the unit is turned on for the first time,
press [POWER] without unplugging the power cord.
Audio Cable
Video Cassette
Recorder
Notes:
●
The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for
connecting monaural audio equipment.
●
The S-VIDEO jack is given priority over the VIDEO jack.
Rear of this TV
REMOTE CONTROL AND FRONT PANEL FUNCTION
123
456
789
0
+100
MENU
o
n
p
m
MUTE SLEEP
DISPLAY
CH RET
INPUT
SELECT
POWER
CH
VOL
POWER button
To turn TV on/off
Channel number buttons
CH(ANNEL) KK/LLbuttons
MENU button
To view on-screen menu
SLEEP button
DISPLAY button
To display CH No./Audio Status
CH(ANNEL) RET(URN) button
To return to previous channel
INPUT SELECT button
To select TV or external input
MUTE button
To mute sound
VOL(UME) XX/YYbuttons
To adjust volume
To select channels
MENUY VOLUME XL CHANNEL KSELECT
POWER
MENUY VOLUME
XL
CHANNEL KSELECT
POWER
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
[EXTERNAL CONNECTION]
ex.
Plug the incoming cable into the ANT jack on the rear of the TV.
*
NOTE (DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled signals
and require a special converter to receive these
channels. Consult your local cable company.
(OUT)
(OUT)
(IN)
(IN)
Note:
•
For your safety and to avoid damages to the unit, unplug the antenna cable from the
ANT jack before moving the unit.
(OUT)
S-Video Cable
(IN)
SELECTING AUDIO/VIDEO INPUT
When you use the AUDIO/VIDEO input jacks, select “VIDEO1” mode by pressing [INPUT
SELECT] on the remote control. The input mode changes by pressing the button as following:
TV channel VIDEO1
VIDEO1 input
You can bracket this product as wall mounting TV using the arm adapted for 100mm (commercially available).
POWER button
To turn TV on/off
SELECT button
CHANNEL KK/LLbuttons
To select channels
VOLUME XX/YYbuttons
To adjust volume
MENU button
To view on-screen menu
Infrared Sensor Window
Photo Stand
Adjust the length of the stand in 5 levels
to change the angle of the TV.
PHOTO STAND
Video Cable
OR
Rear of this TV
OR
Incoming cable from home antenna /
cable company (No cable box)
Incoming cable from cable
company or satellite antenna
Cable box or
Satellite box*
Cable
TV signal
Antenna
OR
INPUT
SELECT
Loading...