Page 1
Wall Mounted Slide/Grab Bar & Hand Shower
with non-positive shut-off, T-600B-V
Installation Instructions
Model Numbers
T-600B-24-V
24 inch slide/grab bar with hand shower
T-600B-24-V-NE
24 inch slide/grab bar with hand shower
and without water supply elbow
T-600B-36-V
36 inch slide/grab bar with hand shower
T-600B-36-V-NE
36 inch slide/grab bar with hand shower
and without water supply elbow
Tools and Materials
5/32" drill bit
1/4" carbide
tip drill bit for
wall tiles
1 2 3 4
Compliance
2010 ADA Standards for Accessible Design
Grab bar assembly and hand shower
with non-positive shut-o complies with
the applicable requirements.
Need Help?
Symmons customer service:
(
800) 796-6667, (781) 848-2250
customerservice@symmons.com
Mon - Fri 7:30 am - 7:00 pm EST
www.symmons.com/service
• Technical help
• Product information
• Warranty policy
Visual Guide Wall Mounted Slide/Grab Bar and Hand Shower T-600B-V
Step 1
Mount grab bar
Six (6) #10 x 2-1/2"
(63.5 mm) wood
screws included
and two (2) spacers
drill hole
5/32 inch
Step 2
Attach slider assembly
Step 3
Hand shower installation
requires that Symmons
pressure-balance mixing valve
include optional check stops
Install hand shower
(-CHKS)
escutcheon
Grab Bar must be
secured with at least
two (2) of three (3)
screws at each end.
bottom side
Adjust for
ease of
movement
at edge
■
SLIDE
■
LOCK
■
SLIDE
wall
elbow
step
washer
vacuum
breaker
washer
hose
Page 2
Installation Notes
Grab Bar Location
For proper mounting heights and location
consult with your state and local code ocial
having jurisdiction over the installation.
Solid Support
■ Grab Bar must be mounted with both
ends positioned over a wall stud. A stud
nder can be used to locate wall studs.
■ Secure through wall board or tile to the
wall stud so as to hold a minimum of
250 pounds of force.
■ At least two (2) of the three (3) screws
provided must be used on each end of
the Grab Bar to properly secure.
Note: Standard size wall stud limits
using more than two (2) screws.
Mounting Grab Bar
■ Drill all holes through wall board into
wood wall studs using a power drill
and a 5/32 inch drill bit.
■ Ceramic tiles -
If installing Grab Bar
over ceramic tiles, rst drill a pilot hole
through the tile using a 1/4 inch carbide
tip drill bit to prevent damage to the tiles.
Next, drill a pilot hole into the wood wall
stud using the 5/32 inch drill bit.
Hand Shower Installation
Check stops - Hand shower installation
requires that Symmons pressure-balance
mixing valve include optional check stops.
Compatibility - Hand Shower is not
compatible on systems that include S-model
mixing valves with IPS connections.
Care and Cleaning
Mild soap and water or a non-abrasive
cleaner is recommended for cleaning.
Dimensions Wall Mounted Slide/Grab Bar & Hand Shower, T-600B-V
Vertical Grab Bar
Model Length
T-600B-24-V 24" (610 mm)
T-600B-36-V 36" (914 mm)
Extend male 1/2" I.P.S.
threads from nished wall
3/8" (10 mm)
1-1/2"
(38 mm)
standard
wooden
wall stud
six (6) #10 x 2-1/2" (63.5 mm)
wood screws included
press-on screwless
escutcheon
3" (77 mm)
diameter
90˚ wall elbow
2-1/2" (64 mm)
diameter
two (2) spacers
3" (77 mm)
diameter
vacuum
supply
breaker
hose
connector
1/2"-14
NPSM
Replacement Parts
Part Number Item
FP-SM6
ADAHS
slider assembly
wand
LOCK
■
Reference
vertical
grab bar
table
supply
outlet
supply
inlet
Ajustable
slider
exible metal
or vinyl hose
1-1/2" (38 mm)
FP-40
INLINE-VB
SP-4
SP-4-6
ST-12RV
ST-12RV6
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ (800)796-6667, (781)848-2250 ■ Fax: (800)961-9621, (781)664-1300
©2012 Symmons Industries, Inc. ■ Printed in U.S.A. ■ www.symmons.com ■ customerservice@symmons.com ■ ZV-999 ■ 072412
wall elbow & ange
vacuum breaker
Hand Shower Hose
■ exible metal (5')
■ exible metal (6')
■ vinyl (5')
■ vinyl (6')
Ordering replacement parts:
Call Symmons customer service at
(800) 796-6667, (781) 848-2250
M-F 7:30 am - 7:00 pm EST or check
our website at www.symmons.com
for a list of Symmons distributors.
bar diameter
Note:
Dimensions subject to
change without notice.
Loading...