Symmons Identity Series, identity 6700, identity 6701, identity 6702 Operation & Maintenance Manual

Identity

CG

6700, 6701, 6702

Operation & Maintenance Manual

™

Model Numbers

6700



Identity Tub/Shower System

6701



Identity Shower System

6702



Identity Tub/Shower System

Modifications

-1.5 1.5 gpm (5.7 L/min) flow restrictor



-2.0 2.0 gpm (7.6 L/min) flow restrictor



-143 3 mode showerhead



-145 5 mode showerhead



-231 2 mode showerhead



-CHKS Integral check stops - for use in



installations where a positive shut-off
device is used downstream of mixing valve

-IPS



-L/HD



-LP Loop handle



-LR Lever handle



-OP 13" oval plate



-REB-TRM



-REV Reverse coring, hot on right, cold on



-SS Slip spout on any tub/shower unit



-STN Satin Nickel finish



-TRM Trim only, valve not included



-X Integral service stops - allows water



1/2" female IPS connections

Less showerhead

Rebuild trim kit

left, for back to back installations

shutoff at valve for service

Specification

6700

Tub/shower system powered by the Temptrol® pressure­balancing valve. Features adjustable stop screw to
limit handle turn. Components made from metal and
nonmetallic materials, plated in standard polished chrome
nish.

6701

Shower system powered by the Temptrol® pressure­balancing valve. Features adjustable stop screw to limit
handle turn, 1 mode showerhead with easy to clean rubber
nozzles and standard 2.5 gpm (9.5 L/min) ow restrictor.
Components made from metal and nonmetallic materials,
plated in standard polished chrome nish.

6702

Tub/shower system powered by the Temptrol® pressure­balancing valve. Features adjustable stop screw to limit
handle turn, diverter tub spout, 1 mode showerhead with
easy to clean rubber nozzles and standard 2.5 gpm
(9.5 L/min) ow restrictor. Components made from metal
and nonmetallic materials, plated in standard polished
chrome nish.

Compliance

-ASME A112.18.1/CSA B125.1

-WaterSense 1.5 gpm (5.7 L/min)

2.0 gpm (7.6 L/min)

For California Residents
WARNING: This product contains chemicals known to
the State of California to cause cancer, birth defects, or
other reproductive harm.

Certied by
CSA Group

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.

Note: Append appropriate -sufx to model number.

Dimensions

FLOORFLOOR

KK

EE

FF

DD

AA MM

NN

JJ

LL

II

BB

CC

GG

OO

PP

HH

Measurements

A 5-7/8", 149 mm
B 4-5/8", 117 mm
C 3-1/2", 89 mm
D 2-7/8", 73 mm
E Ref. 77", 1956 mm

Shower Valve Hole Size

F

G 3-1/2", 89 mm
H 12", 305 mm

I

J

K

L 5-1/4", 133 mm

M Ø 2-1/2", 64 mm

N Ø 3-1/8", 79 mm

O Ø 6-3/8", 162 mm

P Ø 2-1/2", 64 mm

Min. Ø 3", 76 mm

Max. Ø 4", 102 mm

Rough-in

2-3/8" ± 1/2", 60 mm ± 13 mm

Male 1/2" NPT tting must

protrude 4" (102 mm)

from nished wall

6700, 6702

Ref. 32", 813 mm

6701

Ref. 42", 1067 mm

Notes:

1) All dimensions measured from nominal rough-in (see I as reference).

2) Dimensions subject to change without notice.

2

Parts Breakdown

Replacement Parts

C

Item Description Part Number

B

A

I

G

F

H

H

HOT

Water Supply

D

J

COLD

Water Supply

A Showerhead 672SH*

B
C
D
E

F Dome Cover T-19*

G
H

*Note: Append -STN to part number for

Shower Arm

Flange

Handle

Set Screw

Shower

Escutcheon Kit

I

J Tub Spout 054*

Satin Nickel nish.

300S*

RTS-084*

6700-ESC*

Tools Required for Installation

Adjustable

Wrench

Allen Wrench

3/32"

E

Phillips Head

Screwdriver

Notes:

1) Apply a bead of silicone around the perimeter of all shower trim installed
ush to the nished wall (less mounting plates and brackets).

Leave opening on bottom of escutcheons for weep hole.

2) Apply plumber tape to all threaded connections.

Plumber Tape

Silicone

3

2

2

2

2

2

Installation

Note:

For valve body installation, please
see valve body manual.

1) Install shower mounting plate (I)
to shower valve. Secure with two
screws (H).

I

1

H

H

2) Attach shower escutcheon (G) to
shower mounting plate (I).

3) Install dome cover (F) to shower
valve by turning clockwise.

G

1

F

4) Install shower handle (D) to shower
valve. Secure shower handle with
set screw (E).

5) Install tub spout (J) to pipe tting
Turn clockwise to tighten.

J

6) Attach shower arm (B) and ange
(C) to vertical shower pipe. Turn
clockwise to tighten.

1

C

1

1

B

2

G I

Note: Tabs should snap into place.

1

D

E

Note: Handle should be facing the
6 o’clock position.

3

7) Install showerhead (A) to shower
arm (B). Turn clockwise to tighten.

B

1

1

A

4

Operation (Temperature Control)

1) Turn shower handle counter­clockwise approximately 1/4 turn
to put valve in cold position.

2) Turn shower handle counter­clockwise approximately 1/2 turn
to put valve in warm position.

Operation (Diverter Control for 6702 only)

1) Diverter lever in down position for
tub spout operation.

3) Turn shower handle counter­clockwise approximately 3/4 turn
to put valve in hot position.

2) Diverter lever in up position for
shower operation.

Troubleshooting Chart

Problem Cause Solution

Finish is spotting.

Elements in water supply may cause

water staining on nish.

Clean nished trim area with a soft

cloth using mild soap and water or a

non-abrasive cleaner and then quickly

rinse with water.

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: [phone] ■ Fax: [phone]

Copyright © 2017 Symmons Industries, Inc. ■ symmons.com ■ [e-mail] ■ ZV-3196 REV B ■ 021617