Symmons Dia ADA Series, Dia 353GB-12, Dia 353GB-24, Dia 353GB-18, Dia 353GB-36 Operation & Maintenance Manual
...
®
Dia
353GB-12 (18, 24, 36, 42)
ADA Grab Bar Series
Operation & Maintenance Manual
Model Numbers Specification
353GB-12 12" Grab Bar for ADA Applications
☐
353GB-18 18" Grab Bar for ADA Applications
☐
353GB-24 24" Grab Bar for ADA Applications
☐
353GB-36 36" Grab Bar for ADA Applications
☐
353GB-42 42" Grab Bar for ADA Applications
☐
Finish Options
-STN Satin Nickel finish
☐
Note: Append appropriate -sufx to model number.
Dimensions
AA
BB
CC
• Supports up to 250 lbs.
• 1-1/2" bar diameter
• 3" ange diameter
• Bar extends 1-1/2" from wall
• Concealed mounting for a clean look
• Meets WW-P-541/8B Federal Specication for
Manufacturing
• Meets ADA load requirements when properly installed
• Stainless steel construction
• Grab bar compatible with WingIts stainless steel grab
bar fasteners (p/n GBW40) for drywall applications
Warranty
Limited Lifetime - to the original end purchaser in
consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Measurements
A 1-1/2", 38 mm
15", 381 mm (353GB-12)
21", 533 mm (353GB-18)
B
27", 686 mm (353GB-24)
39", 991 mm (353GB-36)
45", 1143 mm (353GB-42)
FF
12", 305 mm (353GB-12)
18", 457 mm (353GB-18)
C
24", 610 mm (353GB-24)
36", 914 mm (353GB-36)
42", 1067 mm (353GB-42)
D Ø 1-1/2", 38 mm
E (2x) Ø 3-1/16", 78 mm
F 3-1/16", 78 mm
G 1/2", 13 mm
DD
EE
FINISHED WALLFINISHED WALL
Note: Dimensions subject to change without notice.
GG
Parts Breakdown
(6) WOOD SCREWS
#10 x 2-1/2"
Tools Required for Installation
Drill:
• 7/64" Drill Bit for Wall
• 1/4" Carbide Tip Drill
Bit for Ceramic Tile
WALL STUD
Pencil
WALL
Phillips Head
Screwdriver
Safety Glasses
Silicone
Grab Bar must be
secured with at least
two (2) of the three (3)
Stud Finder
screws at each end on
the inner side of anges.
IMPORTANT NOTES FOR PROPER INSTALLATION
DO NOT install this product without rst reading and understanding the instructions. If you are unable to understand
these warnings and instructions, contact professional or technical personnel for assistance - otherwise injury may occur.
Grab Bar Location
• For proper mounting heights and location consult with your state and local code ofcial having jurisdiction over the
installation.
Solid Support
• Grab Bar ends must be mounted with both end positions over a wall stud. A stud nder can be used to locate wall
studs. Contractor is responsible for installing Grab Bar to wall studs as instructed.
• Secure through wall board or tile to the wall stud so as to hold a minimum of 250 pounds of force.
• At least two (2) of the three (3) wood screws provided must be used on each end of the Grab Bar, top and bottom, to
properly secure. Standard size wall stud limits using more than two (2) wood screws.
• If using a drill to install wood screws, a drill bit extension must be used to avoid damaging the Grab Bar.
Installation (Wall & Wall Studs)
1) Place Grab Bar at desired position.
Remove covers from bar anges and
mark drill hole locations with pencil at
each end on inner side of anges.
2) Remove Grab Bar from wall. Use
drill with 7/64" drill bit to drill holes
into wall and wall studs at the
marked positions.
2
3) Align mounting holes on Grab Bar
with drill holes. Insert wood screws
into pilot holes for wall and wall
studs. Hand tighten wood screws.
Loading...