Symmons Carrington SLW-4412 Installation And Service Instructions Manual

Carrington™

Widespread Lavatory Faucet SLW-4412
Installation and Service Instructions

Caution: Be sure to turn o hot and cold water supplies
before installing or servicing faucet.

care not to over tighten the locknut, causing damage

Installation Procedure

1. Push valve bodies through holes in sink from

underneath. Make sure ange nuts and mounting
washers are on underside of sink. Valve with red striped

hose (hot) is on the le and blue (cold) is on the right.
Put gasket (LN-129) over valve body. read escutcheon
(LN-128) onto valve body. e top of the valve spindle
should measure 1-7/8” from mounting surface (See
rough in drawing).

2. read collar (LN-112) on to valve body until it reaches

the escutcheon (LN-128).

3. CRP handle installation: Ensure valve spindle is rotated

to the OFF position. Place handle on valve spindle and
thread screw (LN-121A) into valve.

4. Tighten ange nuts and mounting washers from

underneath sink and secure with mounting screws if
nec essar y.

5. Install spout (LN-254A) and centerbody (LN-188)

through center in sink hole from above sink. Secure
spout to sink with washer (LN-138) and nut (SPF-26).
Washer (LN-138) at side should face back of the sink.
read tee (LN-189) to bottom of centerbody (LN-188).

6. read ex hose adapters into tee (LN-189) using pipe

sealant on the threads. Attach ex hoses to ex hose
adapters.

7. Connect hot supply to le tube and cold supply to right

tube using appropriate connectors.

8. Pop-up drain installation:

a ) Remove pop-up plug, tail piece and ange from

the drain body. Make sure that locknut is threaded
all the way down onto the body with at friction
washer in middle and beveled washer on top.

b ) Apply plumbers putty or sealant to bottom of

ange.

c ) Install drain body through drain opening in

lavatory and screw ange onto the drain body
making sure that the threads are completely
engaged for proper sealing and strength of the
connection. Apply joint compound to all threaded
parts to insure proper seal. Apply putty or teon
tape to tail piece before attaching to drain body.

d ) Tighten locknut to compress the beveled ange

evenly across the bottom of the drain opening taking

8. It is very important to thoroughly ush the supply lines

Replacing cartridge (KN-113 or KN-114):

1. Remove plug button (LN-243H or LN-243C), loosen

2. Remove collar (LN-112) by turning counter clockwise.

3. Place wrench on cartridge hex nut (KN-113, KN-114).

4. Install new cartridge. Turn cartridge with wrench until

to the lavatory. Apply teon tape (clockwise) on tail
piece and thread into outlet of body.

e ) Insert pop-up plug and pivot rod into body and

tighten retaining nut until the ball is seated on the
ball washer.

Note: e pop-up plug can be installed either in the
removable or non-removable position, depending
on the location of the hole located in the guide at
the bottom of the plug.

f ) Slide the pivot rod through one side of the spring

clip, then the appropriate adjustment hole and then
other side of the spring clip.

g ) Insert li rod through faucet housing and the top of

the li strap and secure it in place by tightening the
screw.

Note: To insure proper operation of li rod and
pop-up, some adjustment of the linkage may be
required.

ere are two possible adjustment points:

1) li strap to li rod

2) li strap to pivot rod

to prevent foreign matter, i.e. copper chips, sand, stones,
etc. from damaging the sealing surfaces of cartridge.

Remove aerator and open hot and cold to full open then
open both supplies. Let water run through hot and cold
long enough to ush supply lines thoroughly. Shut o
faucet and replace aerator. Check for leaks.

Phillips head screw (LN-121A) and remove handle (LN-

177).

Caution: Do not use wrench as this may damage the
surface nish.

Turn wrench counterclockwise until cartridge is
removed.

cartridge does not turn easily then turn 1/4 to 1/2 turn
further. Reassemble handle in reverse fashion.

Dimensions Carrington Two Handle Widespread Lavatory Faucet, SLW-4412

8"(203 mm) min

16"(406 mm) max

2-5/16" dia
(59 mm)

4" (102 mm) min

7-1/8"

(181 mm)

2" (51 mm)

2-7/16"

(62 mm)

Deck thickness

1-3/8" (35 mm) max

Hole size

1-1/4" (32 mm)

5/8" dia
(16 mm)

1-1/2" (38 mm) min
1-5/8" (41 mm) max

1/2"-14 NPSM

Flexible hose

Note: Dimensions subject to change without notice

Parts Assembly Carrington Two Handle Widespread Lavatory Faucet, SLW-4412

KN-114 Valve cartridge (1)
L-26 O-ring (2) (plug button)
LN-112* Collar (2)
LN-121A Handle screw, M4x10, SS, panhead (2)
LN-128* Escutcheon, widespread (2)
LN-129 Gasket, Escutcheon (2)
LN-138 Washer
LN-150 O-ring (2)
LN-177* Cross handle (2)
LN-185 Gasket, spout
LN-188 Centerbody
LN-189 Centerbody tee
LN-243C Plug button, porcelain (cold)
LN-243H Plug button, porcelain (hot)
LN-254A* Spout
P-108CL12* Lift rod (for pop-up drain assembly)
SPF-26 Nut, Hex (centerbody)

WSF-CRP-KIT Handle kit (qty 2 handles)
*For Decorative Finish Faucets add sufx to parts

marked with an asterisk as follows:
Sufx -STN Radiance® satin nish

Aerator

(ow regulator)

Part Number
Standard Aerator

(red stripe on hot hose)

LN-243H (1)

Handle kit
(2 handles)

KN-114

LN-254A

Aerator insert

2.2 gpm

LN-188

Mounting screws

LN-189

Flex hose adapter

Flex hose

5-13/16"
(148 mm)

4-5/32"

(106 mm)

Hole size

3/4" (19 mm)

1-9/16" (40 mm)

7-1/4"

(184 mm)

1-7/8"

(48 mm)

1" dia

(25 mm)

LN-243C (1)
L-26 (2)
LN-121A (2)
LN-177 (2)
LN-112 (2)
LN-128 (2)
LN-129 (2)

P-108CL12

KN-114

LN-185
LN-138
SPF-26
LN-150

Mounting washer
Flange nut

(blue stripe
on cold hose)

2.2 gpm (8.3L/min) ----

1.5 gpm (5.7L/min) LN-741

1.0 gpm (3.8L/min ----

For California Residents
WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184
Phone: [phone]
Website: symmons.com

Copyright © 2017 Symmons Industries, Inc.

■ Fax: [phone]

■ Email: [e-mail]

*

■ ZV-577 REV D ■ 020317

P-26*
Grid drain
(optional)

RL-154LR*
Pop-up drain assembly
(without lift rod)