Symmons Canterbury SRT-4570, Canterbury SRT-4570-STN Installation And Service Instructions Manual

Canterbury

Roman Tub Faucet SRT-4570

Installation and Service Instructions

®

Model Numbers

SRT-4570 ..............Chrome finish

SRT-4570-STN

.....Satin Nickel finish

Tools & Materials

1/8"

1 2 3 4

Quick Install Guide Canterbury Roman Tub Faucet, SRT-4570

Step 7

Attach water spout

 Need Help?

Symmons customer service:
Phone: [phone]
Email: [e-mail]
Monday - Friday 7:30 am - 6:00 pm EST

www.symmons.com/service

Compliance

ASME A112.18.1/CSA B125.1

Step 8

Flush water supply lines

Step 5

Attach handles



Step 3

Mount valve assembly

Step 4

Attach valve assembly

Step 2

Solder valve assembly together

Step 1

Cut copper tubing to length

WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects,

or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Step 6

Connect water supply lines
and check for leaks

nished deck

Installation Instructions

Caution: If replacing an older faucet ensure water supply is

turned OFF before removing and then turn faucet handles ON
to relieve water pressure.

Step 1 Cut copper tubing to length

Length = (d) minus 2-1/4 inches (57 mm) divided by 2.

center to center distance (d)*

1/2" (12.7 mm) copper tubing

Step 3 Mount valve assembly to deck

nished deck
front view

red

(hot)

blue (cold)

Step 4 Attach valve assembly to deck

Example:

If center to center distance (d) is 14 inches.

-

14 inches minus 2-1/4 inches = 11-3/4 inches.

-

11-3/4 inches divided by 2 = 5-7/8 inches.

-

Cut 2 copper tubes into 5-7/8 inch lengths.

-

* Maximum distance (d) with supplied
copper tubing is 18-1/4 inches (463 mm)

Step 2 Solder valve assembly together

nished deck

front view

D1

Thread down until

stop is reached

D1 = D2

D2

Ensure valves are

parallel aligned

when soldering.

Page 2

Step 5 Attach faucet handles

1/8"

OFF = CW

Step 8 Flush water supply lines

OFF = CCW

Care of faucet finish

Clean nish area by using mild soap and water or non-abrasive
cleaner and then rinse immediately. A non-abrasive wax may
be used to preserve nish area.

Step 6 Solder supply lines to valve inlets

hot

cold

Step 7 Attach faucet spout to deck

Valve cartridge replacement

Step 1 Remove faucet handle and collar

Step 2 Remove and replace cartridge

Step 3 Attach collar and faucet handle

OFF = CW

OFF = CCW

Page 3

Dimensions Canterbury Roman Tub Faucet, SRT-4570

2-1/16" (52 mm) dia.

3-1/8"

(80 mm)

4"

102 mm

Finished deck thickness

1-3/8" (35 mm) max.

1" dia. (25 mm)

Hole size

1-1/16" (27 mm) min.

1-1/2" (38 mm) max.

8" (203 mm) min.

18-1/4" (464 mm) max. with

Symmons supplied copper tubing

3-13/16"

96 mm

Connect using
1/2" copper tubing

1-15/16"

Parts Assembly Canterbury Roman Tub Faucet, SRT-4570

plug button

hot/cold identier

screw

handle

collar

fastener

gasket

spout

plug button
screw

Part Number Item (Qty)

LOCT-RB-KIT

2 handles
included

10-11/16" (272 mm)

3"

48 mm

76 mm

3-15/16"
(101mm)

8-9/16" (218 mm)

Replacement Parts

plug button (2)

*

fastener (2)

3-1/4"

83 mm

screw (2)

handle (2)

collar (2)

gasket (2)

aerator

RT-106*

valve cartridge

ange nut

hot/cold identier

valvebody

copper tube

tee

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184
Phone: [phone]
Website: symmons.com

Copyright © 2019 Symmons Industries, Inc.

■ Fax: [phone]

■ Email: [e-mail]

■ ZV-579 REV C ■ 091919

plug

centerbody

retainer

ange nut

KN-114E (hot)

OFF = CW

KN-113E (cold)

OFF = CCW

Note: For decorative nish faucets add sufx

*

letters to parts marked with an asterisk.

Ordering replacement parts:

Call Symmons customer service at [phone],
[phone] M-F 7:30 am - 6:00 pm EST or
check our website at www.symmons.com for a
list of Symmons distributors.

KN-113E

identified
by groove

valve cartridge