Symmons Allura SLW-4712, Allura Series Installation And Service Instructions Manual

Allura

NSF International

®

Widespread Lavatory Faucet SLW-4712

Installation and Service Instructions

Model Numbers

SLW-4712

Note: Instructions replace document
ZV-782 as of June 2012.

Lavatory faucet with
pop-up drain

Alternate Finish Code

append to part numbers when applicable

-STN

--

Satin Nickel
Chrome (standard)

Quick Install Guide Allura Widespread Lavatory Faucet, SLW-4712

Attach control valves to sink

Tools & Materials

Pipe

Sealant

Compliance

- ASME A112.18.1/CSA B125.1

- NSF/ANSI 61.9, NSF/ANSI 372

- WaterSense 1.0 & 1.5 gpm

Step 1

Step 1

5/64"

Plumbers

Putty

 Need Help?

Contact Symmons customer service at
[phone], [phone]
Email: [e-mail]
Monday - Friday 7:30 am - 7:00 pm EST

 Please check Symmons website

for technical help, the latest product
information and warranty policy.

www.symmons.com/service

Certied by

Step 2

Attach center spout to sink

Step 9

Flush water supply lines

SConnect water supply lines

Step 5

Install stopper and

set eye position

Fasten drain body and

tail piece to sink

Attach drain body to drain trap

Step 3

Non­Removable Removable

Stopper Stopper

Step 4

Step 8

Step 7

Connect lift rod, clevis strap,
pivot rod and adjust linkage

Step 6

Attach pivot rod to drain body

Installation Instructions

PLUMBERS

PUTTY

Installation Instructions

Caution: If replacing an older faucet ensure water supply is

turned OFF before removing. en turn both faucet handles to
the ON position to relieve water pressure.

Step 1 Attach control valves to sink

■ read ange nut
down about 2 inches
from threaded end
of valve body.

fastener

gasket

■ Insert valve body
from underneath
sink up through
mounting hole.

Ensure valve with
red striped hose (hot)
is on the le and blue
(cold) is on the right.

valve body

mounting washer

ange nut

mounting screws

■ Place gasket over valve
body and thread
fastener onto valve
body until fastener

is secured tightly to
valve body.

■ Ensure spindle
is rotated to the

OFF position.

plug button

screw

handle

spindle OFF

hot = cw
cold = ccw

Fasten handle to top
of spindle located
in OFF position as
shown in illustration.

■ Press plug button into
top of handle.

■ Tighten ange nut
and mounting washer
under sink and secure with mounting screws if necessary.

Step 2 Attach center spout to sink

■ Unscrew tee and
remove washer and
nut from threaded
end of spout as
typically shipped.

■ Insert through
mounting hole
in sink and then
fasten from under
sink with washer
and nut.

■ Tighten nut while
ensuring spout
is centered over
mounting hole and
at edge of washer is
facing rear of sink.

washer

nut

tee

spout

Step 3 Connect water supply lines

■ read tee onto
end of spout.

Note: is may

require 4 inches
of clearance.

■ Apply pipe
sealant on both
ex hose adapters.
read into side
of tee.

valve

outlet

& inlet

ex hose

adapter

tee

■ Attach ex hoses
to ex hose

adapters.

Pipe

Sealant

■ Plumb hot
water supply to
le valve body

ex hose

inlet, cold water
to right inlet
(1/2 inch supply hoses not included).

■ Check for leaks if only replacing faucet and drain is already
installed by rst turning faucet handles to the OFF position
and then turn water supply valves ON.

Step 4 Fasten drain body to sink

■ Remove stopper, unscrew ange and remove at rubber
washer from end
of drain body as shipped.

■ Apply plumber’s putty
around bottom of ange.

■ Move friction washer,

beveled washer and
ange nut down away

from end of drain body.

■ Place ange into drain
opening and from under
sink screw drain body
into ange at least
turns until hand tight.
Apply putty or teon tape
to tail piece and attach to
drain body.

■ Position drain body so
pivot cavity is facing rear of
sink and then slide beveled
washer and friction washer
up against sink.

■ Tighten ange nut up
against friction washer to
evenly compress beveled washer while also ensuring ange is
centered in drain opening.

Take care not to over tighten ange nut.

Page 2

2-3

ange nut

drain body

tail piece

spout

valve

body

ange

beveled
washer

friction
washer

pivot
cavity

Step 5 Install stopper and set eye position

pivot rod
retaining nut
outer seat
pivot ball
inner seat
pivot cavity

Stopper can be removable
or non-removable
determined by position
of eye hole when
inserting pivot rod.

non
removable removable

■ Insert stopper
through ange

opening and rotate to
position eye hole.

Removable stopper

When installed in removable position, move pivot rod to
the up position (li rod is in the down position when later
installed). Eye hole will slide over end of pivot rod.

Step 6 Attach pivot rod to drain body

■ Remove retaining nut and outer seat from pivot cavity.

■ Insert pivot rod into

pivot cavity so pivot
ball is against inner
seat and rod passes

under end of stopper
according to selected
eye hole position.

■ Insert outer seat
over pivot rod with
curved end against
pivot ball.

■ Fasten pivot rod to drain body with retaining nut
and tighten using your ngers until ball is seated
snug and pivot rod can move around freely.

Step 7 Connect lift rod and adjust linkage

■ Insert li rod through hole on top of water spout.

■ Fasten end of pivot
rod with spring clip
through location hole
in clevis strap that is
best aligned to enable
li rod also fasten to
end of clevis strap when
in the up position and
stopper is in the closed
position.

■ Insert li rod into
end of clevis strap
and fasten with
thumb screw at location
where stopper can be
easily opened and
closed.

If necessary, select
another location hole
in clevis strap and re-adjust li rod where fastened to clevis

strap

clevis strap

stopper

ange

lift rod

thumb
screw

location
holes

spring
clip

pivot rod

Step 8 Flush water supply lines

oroughly ush the supply lines to prevent foreign matter, i.e.
copper chips, sand, etc.
from damaging the
sealing surface inside
control valves.

■ Remove aerator from
end of faucet water

remove

aerator

outlet by rotating
counter clockwise.

■ Turn hot and cold
faucet handles
to full ON position,
open water supply
valves
and run long enough to ush supply lines thoroughly.

■ Turn faucet OFF, replace aerator, and check for any water leaks.

Care of faucet finish

Clean nish area by using mild soap and water or non-abrasive
cleaner and then rinse immediately. A non-abrasive wax may
be used to preserve nish area.

Valve cartridge replacement

Remove faucet handle

■ Pry loose and remove plug button
using your nger.

■ Remove Phillips head screw
in center of handle.

■ Li o handle from
cartridge spindle.

Remove cartridge

Using a wrench, turn hex nut
on cartridge counter clockwise.

Note: Ensure valve assembly doesn’t

rotate under sink while turning nut.

Insert new cartridge

Insert replacement cartridge into
center of valve and tighten hex nut
using a wrench.

Attach handle

■ Ensure cartridge spindle is
rotated to the OFF position.

■ Attach handle located
in the OFF position as
shown in illustration.

■ Insert screw into
center of handle
and replace plug button.

Page 3

plug button

screw

handle

spindle OFF

hot = cw
cold = ccw

cartridge

valve

handles set in

the OFF position

LN-15
FLR-110-1.5
FLR-110-1.0

aerator ow rates

2.2 gpm (8.3L/min)

1.5 gpm (5.7L/min)

1.0 gpm (3.8L/min)

Parts Assembly Allura Widespread Lavatory Faucet, SLW-4712

*

faucets with an optional decorative nish, append
appropriate three letter nish sufx code to part
numbers marked with an asterisk (

*

4-1/2"

(114 mm)

6-5/16"

(160 mm)

5/8" dia (16 mm)

Hole size
1-1/8" (29 mm) min
1-1/2" (38 mm) max

5/8" (16 mm)

3-1/4"

(83 mm)

1-5/8" (42 mm)

2-1/2"

(64 mm)

3-1/8" (79 mm)

1" dia. (25 mm)

Hole size

1-1/16" (27 mm) min

1-7/16" (37 mm) max

4" (102 mm)

Flexible hose

Deck thickness

1-3/8" (35 mm) max.

Dimensions

Allura Widespread Lavatory Faucet, SLW-4712

2-1/4" dia
(58 mm)

2-5/16" dia
(59 mm)

1/2"-14 NPSM

8" (203 mm)

Note: Dimensions subject to change without notice.

lift rod

P-108CL12

standard aerator

faucet handle

reference table

valve cartridge

reference table

(red stripe on hot hose)

WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth
defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

pop-up drain

assembly

RL-154LR

includes lift rod

and stopper

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: [phone] ■ Fax: [phone]

Copyright © 2018 Symmons Industries, Inc. ■ symmons.com ■ [e-mail] ■ ZV-1084 REV F ■ 071318

*

2.2 gpm

stopper

P-100N

*

(blue stripe
on cold hose)

Replacement Parts

Part Number Item

RL-072*

KN-114 (hot)

OFF = CW

KN-113 (cold)

OFF = CCW

Handle kit

plug buttons

screw

handle

KN-113

identified
by groove

valve cartridge

*

*
*

Note: When ordering replacements parts for

).

Ordering replacement parts:

Call Symmons customer service at [phone],
[phone], M-F 7:30 am - 7:00 pm EST or
check our website at
list of Symmons distributors.

www.symmons.com

aerator

for a