Symmons 4700-TRM Installation Manual

4700-TRM, 4701-TRM, 4702-TRM
Allura® Trim Series

Operation & Maintenance Manual

Model Numbers Specification

4700-TRM

Valve Trim

4701-TRM

Shower Trim

4702-TRM

Tub/Shower Trim

Options/Modifications

-1.5

1.5 gpm (5.7 L/min) flow restrictor

-2.0

2.0 gpm (7.6 L/min) flow restrictor

-LAM

Metal finish insert handle

-LR

Lever handle

-SS

Slip spout on any tub and shower unit

Tub/shower trim with lever handle includes diverter tub
spout and 3 mode showerhead with standard 2.5 gpm
(9.5 L/min) ow restrictor. Shower trim with lever
handle includes all of the above less diverter tub
spout. Valve trim with lever handle includes valve trim
only. Components made from metal and nonmetallic
materials plated in standard polished chrome nish.

Compliance

-ASME A112.18.1; CSA B125.1

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.
5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete
warranty information.

-STN

Satin Nickel finish

Note: Append appropriate -sufx to model number.

Dimensions

CC

A

D

D

B

B

Measurements

A Ø 2 1/2”, 64 mm
B 6 3/4”, 172 mm
C Ø 7”, 178 mm
D Ref. 77”, 1956 mm
E 2 1/2", 64 mm

Ref. 32”, 813 mm

F

G 12”, 305 mm
H 3 1/8”, 79 mm

I 3 1/2”, 89 mm

J 4”, 102 mm

K

2 3/8” ± 1/2”, 60 mm ± 13 mm

L 1/2” NPT

M 4”, 102 mm

I

I

N 5 1/4”, 133 mm

(4702-TRM)

Ref. 42”, 1067 mm

(4700-TRM, 4701-TRM)

Rough-in

H

G

G

H

J

J

FF

LL

E

E

M

M

N

N

Floor

Floor

FloorFloor

Notes:

1) All dimensions measured from nominal rough-in (see K as reference).

2) Dimensions subject to change without notice.

K

K

2

Parts Breakdown

Replacement Parts

Item Description Part Number

B

A Showerhead 4-143

C

A

J

B Flange 430SS

C

D
E
F
G
H Dome Cover T-19

I

J

K*

L Diverter Tub Spout 054

Notes:

1) Append -STN to part number for Satin Nickel
nish.

2) Append -1.5 or -2.0 to showerhead for low
ow.

Shower Arm

(ange included)

Plug Button

Handle Screw

Star Washer

Handle

Dial

Mounting Screws

Shower Escutcheon

300S

RTS-026

T-133C

G

F

D

H

I

K

Tools Required for Installation

Adjustable

wrench

E

Phillips head

screwdriver

L

*Note: Apply a bead of silicone around the perimeter of the escutcheon

after installing trim ush with wall. Leave opening on bottom of
escutcheon for weep hole.

Plumber tape

Silicone

3

Installation

2

3

2

2

2

Note:

For valve body installation, please
see valve body manual.

1) Install escutcheon (K) to shower
valve. Secure with two screws (J).
Snap dial (I) into escutcheon.

K

1

J

I

2

3

Note: Logo on dial should be in the
6 o'clock position.

2) Install dome cover (H) to valve by
turning clockwise.

3) Install handle (G) to valve.
Secure handle with star
washer (F) and screw (E). Attach
plug button (D) to handle.

G

1

F

E

D

Note: Handle should be facing the

6 o'clock position.

4) Install tub spout (L) to pipe tting.

Turn clockwise to secure.

5) Attach shower arm
ange

(B)

to vertical shower pipe

(C)

turning clockwise to tighten.

2

B

C

6) Install showerhead
er arm

(C)

turning clockwise to

(A)

tighten.

C

1

A

and

1

to show-

1

1

L

H

4

Operation & Maintenance

Temperature Control

1) Turn shower handle counterclockwise approximately
1/4 turn to put valve in cold position.

2) Turn shower handle counterclockwise approximately
1/2 turn to put valve in warm position.

Troubleshooting Chart

Finish is spotting.

Elements in water supply may cause

water staining on nish.

3) Turn shower handle counterclockwise approximately
3/4 turn to put valve in hot position.

Clean nished trim area with a soft

cloth using mild soap and water or a

non-abrasive cleaner and then quickly

rinse with water.

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: [phone] ■ Fax: [phone]

©2015 Symmons Industries, Inc. ■ www.symmons.com ■ [e-mail] ■ ZV-3060 REV B ■ 020315