Page 1
8 3/
4
"
222mm
6
1
/4"
159mm
14
3
/4"
375mm
4
1
/8"
105mm
11/2"
38mm
2"
52mm
5
1
/2"
140mm
1
1
/2"
38mm
5
3
/4"
146mm
23 1/2"
597mm
1
1
/2"
38mm
4"
102mm
2
5
/8"
66mm
3
5
/8"
91mm
3 1/4"
82mm
26
1
/2"
673mm
16"
407mm
max.
4 1/2"
114mm
min.
3
3
/4"
96mm
2 1/4"
56mm
Shower
Head
Height
stops accessible
after removing
handle & dome
Thru wall supplies may enter at any position between
minimum and maximum distances shown.
Recess in wall to be 28" high,
5 3/4" wide and 2 1/4"
minimum deep, by others.
floor line
HC
17"
432mm
5 3/4"
146mm
(8 Holes)
9/32
1-911 & 1-912 Series
INSTALLATION INSTRUCTIONS
Product meets ANSI A112.18.1M
Flow rate: 2.5 gpm (9.5 L/min)
Drilling pattern for valve
and piping assembly
®
Hydapipe
Recommended head heights
Men ____________________________ 6’4”
Boys, Senior High _________________ 6’0”
Boys, Junior High _________________ 5’7”
Boys, Elementary _________________ 5’4”
Women _________________________ 6’0”
Girls, Senior High _________________ 5’8”
Girls, Junior High _________________ 5’5”
Girls, Elementary __________________ 4’2”
INSTALLATION:
1. With special screwdriver provided
remove screw located on shield above
valve, remove head bracket with hex
socket key, remove large locking nut,
remove valve handle with hex socket
key, remove dome and nameplate
with locking ring. Remove unit cover.
2. You will have to frame in the opening
per the drawing dimensions
3. Mount valve and piping assembly to
frame with screws and anchors provided. Connect supply piping.
4. Replace unit cover and reassemble in
reverse order.
5. Install shower head.
Page 2
HPN-123
T-12A
T-17
T-16
T-11
TA-10
T- 8
T- 7
T- 5
T- 3
T- 2
T- 1
LM-26-SW
TA-9
(includes T-11)
TA-4
HPN-107
HPN-28
HPN-107
HPN-14
L-23
HPN-15
T-34
HPN-13
HPN-9
300A
4-282M
HP-7
HPN-10
HPN-7
T-20PL
RC-14X
SC-15A
SC-15A
HP-7 Screw
HPN-7 Nameplate
HPN-9 Shower head bracket
HPN-10 Dome cover
HPN-11 Head mounting bracket
HPN-13 Mounting bracket nut
HPN-14 Head bracket stud
HPN-15 Pipe and shield bracket
HPN-28 Locking nut
HPN-107 Recessed wall bracket
HPN-123 Unit cover
L-23 O-ring
LM-26 SW Service stop complete
RC-14X Handle
SC-15A Set screw
T-1 Hot renewable seat
T-2 Cold seat o-ring
T-3 Cold renewable seat
T-5 Hot washer screw
T-6 Hot washer
T-7 Cold washer retainer
T-8 Cold washer
TA-10 Flow control spindle
T-11 Cap gasket
T-12A Cap assembly
T-16 Packing, o-ring and washer
T-17 Packing nut
T-20PL Dome lock nut
T-34 Limit stop with o-ring
300A Set screw
4-282M Fre-Flo shower head
TA-4 Hot seat (T-1)
Cold seat (T-3)
Cold seat O-ring (T-2)
TA-9 Hot washer screw (T-5)
Hot washer (T-6),
Cold water retainer (T-7)
Cold washer (T-8),
Cap gasket (T-11)
TA-10 Spindle assembly
Tools required for installation:
Slotted screwdriver, Phillips screwdriver,
soldering equipment, adjustable wrench,
channel lock pliers, hex socket keys (1/8”
and 3/32”), electric drill with 1/4” drill bit,
HY-50 screwdriver (provided)
INDIVIDUAL PARTS INDIVIDUAL PARTS COMPOSITE PARTS
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184
(800) 796-6667, (781) 848-2250 ■ Fax (80 0) 96 1-9 621 , (78 1) 843-3 849
Website: www.s ymm ons .c om ■ Email: c u s tome r s ervi c e @symm o n s.co m
©2007, 2008 Symmons Industries, Inc. Printed in U.S.A. ■ ZV-484 ■ 050208
Loading...