Symmons 1-901 Installation Manual

Download

Page 1

1-901Series

INSTALLATION INSTRUCTIONS

Product meets ANSI A112.18.1M Flow rate: 2.5 gpm (9.5 L/min)

Drilling pattern for valve and piping assembly

Hydapipe

Recommended head heights

Men ____________________________ 6’0”

Boys, Senior High _________________ 5’10”

Boys, Junior High _________________ 5’7”

Boys, Elementary _________________ 5’4”

Women _________________________ 5’8”

Girls, Senior High _________________ 5’8”

Girls, Junior High _________________ 5’5”

Girls, Elementary __________________ 4’2”

For ADA compliance (Americans with Disabilities Act) consult ADAAG or your state regulations for proper product choice and mounting heights. ADAAG does permit a ﬁxed shower head mounted 48” above the ﬂoorin unmonitored facilities where vandalism may be a problem.

INSTALLATION:

1. With special screwdriver provided remove screw located on shield above valve, remove head bracket with hex socket key, remove large locking nut, remove valve handle with hex socket key, remove dome and nameplate with locking ring. Remove unit cover.

2. Mount valve and piping assembly to wall with screws and anchors provided. Connect supply piping.

3. Replace unit cover and reassemble in reverse order.

4. Install shower head.

Page 2

T-17

HP-7

HPN-15

HPN-28

T-11

T-12A

TA-9

(INCLUDES T-11 )

T-16

TA-10

T-8

T-7

T-1

LM-26 SW

T-2

T-3

T-5

T-6

RC-14X

HPN-7

T-20PL

SC-15A

HPN-10

HP-7

T-34

HPN-14

HPN-11

HP-14B

HP-14A

HP-7

HPN-9

HPN-6

HP-7

SC-15A

HPN-13

HPN-5

4-282M

300A

TA-4

L-23

HP-14B

INDIVIDUAL PARTS INDIVIDUAL PARTS COMPOSITE PARTS

HP-7 Screw HP-14A Screw HP-14B Star plastic anchors HPN-5 Top cap HPN-6 Soap dish HPN-7 Nameplate HPN-9 Shower head bracket HPN-10 Dome cover HPN-11 Head mounting bracket HPN-13 Mounting bracket nut HPN-14 Head bracket stud HPN-15 Pipe and shield bracket HPN-28 Locking nut L-23 O-ring LM-26 SW Service stop complete RC-14X Handle SC-15A Set screw

T-1 Hot renewable seat T-2 Cold seat o-ring T-3 Cold renewable seat T-5 Hot washer screw T-6 Hot washer T-7 Cold washer retainer T-8 Cold washer TA-10 Flow control spindle T-11 Cap gasket T-12A Cap assembly T-16 Packing, o-ring and washer T-17 Packing nut T-20PL Dome lock nut T-34 Limit stop with o-ring 300A Set screw 4-282M Fre-Flo shower head

TA-4 Hot seat (T-1) Cold seat (T-3) Cold seat O-ring (T-2) TA-9 Hot washer screw (T-5) Hot washer (T-6), Cold water retainer (T-7) Cold washer (T-8), Cap gasket (T-11) TA-10 Spindle assembly

Tools required for installation:

Slotted screwdriver, Phillips screwdriver, soldering equipment, adjustable wrench, channel lock pliers, hex socket keys (1/8” and 3/32”), electric drill with 1/4” drill bit, HY-50 screwdriver (provided)

INDIVIDUAL PARTS

COMPOSITE PARTS

T-3 Cold renewable seat T-5 Hot washer screw T-6 Hot washer T-7 Cold washer retainer T-8 Cold washer TA-10 Flow control spindle T-11 Cap gasket T-12A Cap assembly T-16 Packing, o-ring and washer T-17 Packing nut T-20PL Dome lock nut T-34 Limit stop with o-ring 300A Set screw 4-282M Fre-Flo shower head

KIT-HP Mounting hardware kit KIT-HPEC Extension cover kit TA-4 Hot seat (T-1) Cold seat (T-3) Cold seat O-ring (T-2) TA-9 Hot washer screw (T-5) Hot washer (T-6), Cold water retainer (T-7) Cold washer (T-8), Cap gasket (T-11) TA-10 Spindle assembly

Tools required for installation:

Slotted screwdriver, phillips screwdriver, soldering equipment, adjustable wrench, channel lock pliers, hex socket keys (1/8” and 3/32”), electric drill with 1/4” drill bit, HY-50 screwdriver (provided)

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 (800) 796-6667, (781) 848-2250 ■ Fax (800) 9 6 1 - 9 6 21, (781) 8 4 3 - 3 8 49 Website: www.symmons. c o m ■ Email: c u st o m ers e r vic e @sy m m ons . c om