Symmons 1-805S Installation Manual
2
3
/4"
70mm
6
1
/4"
159mm
3
1
/8
"
79mm
1
7
/8
"
48mm
2
1
/8
"
54mm
stops
1
1
/
16
"
27mm
7
"
178mm
4
1
/4"
108mm
6
1
/2
"
165mm
3
1
/2
"
76mm
36
" (914mm)
bewteen units
36
" (914mm)
bewteen units
3
1
/
8
"
79mm
9
1
/2
"
241mm
31
3
/8
"
797mm
17
1
/2
"
445mm
4
3
/8
"
111mm
4
1
/4
"
108mm
6
"
152mm
stops accessible
thru bottom
Shower Head
Height
floor line
1-805 Series (standard)
standard unit
short unit
1-806 Series (short)
INSTALLATION INSTRUCTIONS
Product meets ANSI A112.18.1M
Flow rate: 2.5 gpm (9.5 L/min)
Drilling pattern for valve
and piping assembly
®
Hydapipe
INSTALLATION:
1. With the special wrench provided remove the four
vandal-proof screws holding the stainless steel unit
cover to valve and piping assembly (two screws at
head bracket and two screws at valve). Remove
unit cover. Note: head bracket is fastened to unit
cover and is removed with it.
2. Mount valve and piping assembly to wall at specified height with screws and anchors provided.
Connect supply piping.
3. When looking at the drawing supplied, starting
with the cover labeled (A), place horizontal cover
on the wall so that the opening straddles the vertical unit. You then insert anchor and screw in the
horizontal cover to secure it to the wall.
4. The rest of the horizontal covers will follow in
alphabetical order. You will need to leave a ¾” gap
between each horizontal cover.
5. An HP-26 horizontal strap will cover the gap that is
left. It also provides support for the sections.
6. Each corner cover is provided with tabs on them
so that, the horizontal pieces will fit snuggly into
the corner pieces.
7. All copper tubing supplied for crossover fittings on
these units are cut to length and should not be
altered
8. Replace unit covering and fasten with vandal
proof screws.
9. Install showerhead
Recommended head heights
Men _______________________________ 6’4”
Boys, Senior High ___________________ 6’0”
Boys, Junior High ___________________ 5’7”
Boys, Elementary ____________________ 5’4”
Women ____________________________ 6’0”
Girls, Senior High____________________ 5’8”
Girls, Junior High ____________________ 5’5”
Girls, Elementary ____________________ 4’2”
HP-21
ENDCAP
800 HORIZONTAL COVER
(PER JOB SPEC)
3/4" GAP LEFT
BETWEEN ALL
COVERS
HP-26
HP–5 SOAP DISH
HP–4 COVER PLATE
(WHEN SOAP DISH IS NOT USED)
C-13 Dome cover
HP-2 Shield (standard unit)
HP-3 Shield (short unit)
HP-5 Soap dish
HP-6 Nameplate
HP-7 Screw
HP-8 Shower head bracket
HP-10 Body cover
HP-10A O-ring
HP-14 Screw
HP-14A Washer
HP-14B Star plastic anchors
HP-21 Endcap
HP-23 TEE (2 required)
HP-26 Cover Strap
HP-30 Crossover Fitting
HY-1A Piping assembly (standard unit)
HY-1B Piping assembly (short unit)
J-32B O-ring
RC-14 Handle
SC-13C Dial
SC-15A Set screw
SC-18 Lock nut
S2H-8D Set screw
SC-3 Renewable seat
SC-7 Packing nut
SC-9 Cold washer retainer
SC-10 Hot washer
SC-10A Screws
SC-11 Cold washer
SC-17 Packing
SC-19 Cap gasket
SC-26 Limit stop with o-ring
4-131M Super shower head
C-5 Spindle assembly
C-50 Renewable seat socket wrench
KIT-B Washer and gasket kit
SC-2 Cap assembly
SC-3 Renewable seat unit complete
HP-17ASB Stop assembly
Tools required for installation:
Slotted screwdriver, Phillips screwdriver,
soldering equipment, adjustable wrench,
channel lock pliers, hex socket keys (1/8”
and 3/32”), electric drill with 1/4” drill bit,
HY-50 screwdriver (provided)
INDIVIDUAL PARTS INDIVIDUAL PARTS COMPOSITE PARTS
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184
(800) 796-6667, (781) 848-2250 ■ Fax ( 8 00) 961- 9 621, (781 ) 84 3 -384 9
Website: www.sy m mons .com ■ Email: c u s t o merser v i c e @ s y m m o n s .com
©2007, 2008 Symmons Industries, Inc. Printed in U.S.A. ■ ZV-480 ■ 050208
Loading...