Page 1
standard unit
short unit
standard unit
short unit
standard unit
short unit
* Recommended
Shower Head Height
See Below
standard unit
short unit
1-801 Series (standard)
1-802 Series (short)
INSTALLATION INSTRUCTIONS
Product meets ANSI A112.18.1M
Flow rate: 2.5 gpm (9.5 L/min)
Drilling pattern for valve
and piping assembly
®
Hydapipe
Recommended head heights
Men ____________________________ 6’0”
Boys, Senior High _________________ 5’10”
Boys, Junior High _________________ 5’7”
Boys, Elementary _________________ 5’4”
Women _________________________ 5’8”
Girls, Senior High _________________ 5’8”
Girls, Junior High _________________ 5’5”
Girls, Elementary __________________ 4’2”
For ADA compliance (Americans with Disabilities Act) consult ADAAG or your state regulations for proper product choice and mounting heights. ADAAG does permit a fixed
shower head mounted 48” above the floorin unmonitored facilities where vandalism
may be a problem.
INSTALLATION:
1. With special wrench provided remove
four vandal-proof screws holding
stainless steel unit cover to valve
and piping assembly (two screws
at head bracket and two screws at
valve). Remove unit cover. Note: head
bracket is fastened to unit cover and is
removed with it.
2. Mount valve and piping assembly to
wall with screws and anchors provided. Connect supply piping.
3. Replace unit covering and fasten with
vandal proof screws.
4. Install shower head.
Page 2
HP-14(2)
HP-14
HP-14A(2)
HP-14A
HP-14
HP-14A
HP-14B
SC-10A
HP-14B
HP-14B
HP-14B
HY-1A
(STD. UNIT)
HY-1B
(SHORT UNIT)
HP-2
(STD. UNIT)
HP-3
(SHORT UNIT)
HP-4
HP-7
HP-7
HP-7
HP-7
HP-7
HP-7
HP-5
4-231M
SC-15A
SC-18
HP-10
HP-10A
HP-6
C-13
SC-13C
HP-7
HP-7
RC-14
HP-7
HP-7
HP-8
J-32B
S2H-8D
HP-7
HP-7
SC-7
SC-2
C-5
SC-17
SC-26
SC-19
SC-11
SC-10A
SC-10A
SC-10
SC-9
SC-3
HP-17ASB(2)
INDIVIDUAL PARTS INDIVIDUAL PARTS COMPOSITE PARTS
C-13 Dome cover
HP-2 Shield (standard unit)
HP-3 Shield (short unit)
HP-4 Top cap
HP-5 Soap dish
HP-6 Nameplate
HP-7 Screw
HP-8 Shower head bracket
HP-10 Body cover
HP-10A O-ring
HP-14 Screw
HP-14A Washer
HP-14B Star plastic anchors
HY-1A Piping assembly (standard unit)
HY-1B Piping assembly (short unit)
J-32B O-ring
RC-14 Handle
SC-13C Dial
SC-15A Set screw
SC-18 Lock nut
S2H-8D Set screw
SC-3 Renewable seat
SC-7 Packing nut
SC-9 Cold washer retainer
SC-10 Hot washer
SC-10A Screws
SC-11 Cold washer
SC-17 Packing
SC-19 Cap gasket
SC-26 Limit stop with o-ring
4-231M Super shower head
C-5 Spindle assembly
C-50 Renewable seat socket wrench
KIT-B Washer and gasket kit
SC-2 Cap assembly
SC-3 Renewable seat unit complete
HP-17ASB Stop assembly
Tools required for installation:
Slotted screwdriver, Phillips screwdriver,
soldering equipment, adjustable wrench,
channel lock pliers, hex socket keys (1/8”
and 3/32”), electric drill with 1/4” drill bit,
HY-50 screwdriver (provided)
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184
(800) 796-6667, (781) 848-2250
Website: www.symmons. c o m
© 2008 Symmons Industries, Inc. Printed in U.S.A.
■ Fax ( 8 0 0 ) 961-9621, ( 7 8 1 ) 843-3849
■ Email: cu s t om e r se r v ic e @ sy m m on s . co m
■ ZV-334 (fold) ■ ZV-333 (3h) ■ 050708
Loading...