Symmetry Office APEX-SYMAC Series, APEX-SYMAC1, APEX-SYMAC3, APEX-SYMAC2, APEX-SYMAC2D Installation Instructions Manual
INSTALLATION INSTRUCTIONS
Apex Column Mounts
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
APEX-SYMAC1
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
APEX-SYMAC2
APEX-SYMAC2D
APEX-SYMAC Series
APEX-SYMAC3
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
APEX-SYMAC Series Installation Instructions
DISCLAIMER
Symmetry Office intends to make this manual accurate and
complete. However, Symmetry Office makes no claim that the
information contained herein covers all details, conditions or
variations, nor does it provide for every possible contingency in
connection with the installation or use of this product. The
information contained in this document is subject to change
without notice or obligation of any kind. Symmetry Office makes
no representation of warranty, expressed or implied, regarding
the information contained herein. Symmetry Office assumes no
responsibility for accuracy, completeness or sufficiency of the
information contained in this document.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the APEX-SYMAC Series
Monitor Arm and the desk up to (and including) the display
does not the weight limits listed in the table below. Use with
products heavier than the maximum weight indicated may
result in collapse of the mount and its accessories causing
possible injury.
Symmetry® is a registered trademark of Symmetry Office. All
rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
MODEL Max Weight
Allowed for
EACH
Display
APEX-SYMAC1
APEX-SYMAC2
APEX-SYMAC2D
APEX-SYMAC3
22 lbs
(9.98 kg)
22 lbs
(9.98 kg)
9 lbs
(4.08 kg)
7.5 lbs
(3.4 kg)
--SAVE THESE INSTRUCTIONS!--
Max Weight
Capacity of
Mounting
System
22 lbs
(9.98 kg)
44 lbs
(19.96 kg)
18 lbs
(8.16 kg)
15 lbs
(6.8 kg)
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
2
Installation Instructions APEX-SYMAC Series
THICK NESS
HEIGHT ADJUST RANGE
MANUAL (7") + DYNAMIC (13")
HEIGHT ADJ UST RANGE
MANUAL (7") + DYNAMIC (13")
10
DOWN
DIMENSIONS
APEX-SYMAC1
90
10 DOWN
MOUNTING PATTERN
COMPATI BILITY
26.30
6.30
667.9
159.9
100 X 100
75 X 75
APEX-SYMAC2
DESKTOP
RANGE
2.50
.50
63.5
12.7
INTERFACE
ROTATION
90
MOUNTING PATTE RN
COMPATIBIL ITY
100 X 100
75 X 75
DESKTOP THICKNESS
RANGE
2.50
.50
63.5
12.7
26.30
6.30
667.9
159.9
3
APEX-SYMAC Series Installation Instructions
DOWN
APEX-SYMAC2D
MOUNTI NG PATTER N
COMPATIBILITY
100 X 100
RANGE
90
75 X 75
10 DOWN
INTERFACE
ROTATION
APEX-SYMAC3
HEIGH T ADJUST RANGE
MANUAL (7") + DYNAMIC (13")
32.75
12.75
831.7
323.7
DESKT OP THIC KNESS
RANGE
2.50
.50
63.5
12.7
INTERFACE
90
MOUNTING PATTERN
COMPATIBILITY
100 X 100
75 X 75
10
HEIGHT ADJUST RANGE
MANUAL (7") + DYNAMIC (13")
29.58
9.58
751.3
243.3
DESKTOP THICKNESS
RANGE
2.50
.50
63.5
12.7
4
Installation Instructions APEX-SYMAC Series
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
5
Loading...