Symetrix 302 User Manual

302 Dual Microphone

Preamplifier

Users Guide

302

Table of Contents

Chapter 1 Introduction 1

Chapter 2 Operator Safety Summary 2

Chapter 3 Fast Setup 3

Chapter 4 Front Panel Controls 4

Chapter 5 Rear Panel Connections 5

Chapter 6 Using the 302 7

Chapter 7 Applications 9

Chapter 8 Troubleshooting 11

Chapter 9 Specifications 12

Chapter 10 Warranty and Service 13

Chapter 11 Declaration of Conformity 15

Rev A.01, 11 September, 1998

Symetrix part number 53302-0A01

Subject to change without notice.

©1998, Symetrix, Inc. All right reserved.

Symetrix is a registered trademark of Symetrix, Inc.

Mention of third-party products is for informational
purposes only and constitutes neither an endorsement
nor a recommendation. Symetrix assumes no
responsibility with regard to the performance or use
of these products.

Under copyright laws, no part of this manual may be
reproduced or transmitted in any form or by any
means, electronic or mechanical, including photo­copying, scanning, recording or by any information
storage and retrieval system, without permission, in

302

writing, from Symetrix, Inc.

i

Mountlake Terrace, WA 98043 USA

6408 216th St. SW

Tel [phone]

Fax [phone]

Email: [e-mail]

IntroductionChapter 1

Congratulations on your purchase of the
Symetrix 302 Dual Microphone Preamplifier.
The 302 is an ultra-clean two channel dual
mono preamp for use in critical digital and
analog recording situations. The 302 delivers
exceptional sonic performance even at
extremely high input levels, making it the
ideal mate to the newest transformerless
condenser microphone designs.

When compared with older mic preamps, the
302 offers substantial sonic advances, such
as:

1) Its solid stereo imaging (less than 10
degree phase shift at 20kHz);

2) Excellent transient handling (its positive
and negative slew rates are symmetrical);

3) Very low noise (approaching the theoreti­cal limit); and

4) Almost undetectable distortion (.007%).

Variable gain inputs with 15dB pads allow
the 302 to handle any input level up to
+14dBV. Phantom power is available at both
inputs. In addition, both channels include a
polarity switch to correct for improperly
wired cables or unresolvable mic placement
problems.

Balanced low-Z line drivers are on 3-conduc­tor 1/4" TRS connectors and Euroblock
connectors. These drivers are capable of
+24dBm maximum output. The output stage
can also drive unbalanced lines of up to a
maximum of +18dBm.

We recommend that you read this manual
cover-to-cover. You will find the answers to
most of your questions inside. However, if
you are in a hurry, go directly to Chapter 3
(Fast Setup). It will get you started quickly.
Please feel free to contact us if you have
questions, comments or suggestions.

Phone:[phone]

Fax:[phone]

Email: [e-mail]

Website: www.symetrixaudio.com

MICROPHONE 1

GAIN (dB)

CLIP

40

20

60

OUTPUT 2

302

DUAL MICROPHONE
PREAMPLIFIER

Front panel

MANUFACTURED BY SYMETRIX INC. LYNNWOOD, WA USA

POWER

INPUT

THIS PRODUCT CONTAINS NO USER SERVICABLE PARTS.

FABRIQUÉ AUX E.-U. PAR SYMETRIX INC., LYNNWOOD, WASHINGTON.

RÉFÉREZ TOUTE RÉPARATION À UN TECHNICIEN QUALIFIÉ.

Rear panel

CONNECT TO
SYMETRIX PS-3
OR PS-3E POWER
SUPPLY ONLY.

15dB PAD

IN
OUT

OUTPUT 2 OUTPUT 1+2

POLARITY

BALANCED LINE OUTPUTS

180°
0°

CLIP

MICROPHONE 2 PHANTOM POWER

GAIN (dB)

40

20

OUTPUT 1

60

15dB PAD

IN
OUT

OUTPUT 1

POLARITY

180°
0°

ON
OFF

PWR

MICROPHONE INPUTS

INPUT 1INPUT 2

302

1

Operator Safety Summary Chapter 2

.

The information in this summary is intended
for persons who operate the equipment as well
as repair personnel. Specific warnings and
cautions are found throughout this manual
wherever they may apply.

The notational conventions used in this
manual and on the equipment itself are
described in the following paragraphs.

Equipment Markings

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

TO REDUCE THE RISK OF FIRE OR

WARNING:

AVIS:

SEE OWNERS MANUAL. VOIR CAHIER D’INSTRUCTIONS.

No user serviceable parts inside. Refer servicing to qualified service personnel

Il ne se trouve a l’interieur aucune piece pourvant entre reparée l’usager.

The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user of the presence of uninsulated

dangerous voltage within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to per­sons.

The exclamation point within an equilateral
triangle is intended to alert the user of the
presence of important operating and mainte­nance (servicing) instructions in the literature
accompanying the 302 (i.e. this manual).

Caution To prevent electric shock, do not

Terms

Several notational conventions are used in this
manual. Some paragraphs may use Note,
Caution, or Warning as a heading. Certain
typefaces and capitalization are used to
identify certain words. These are:

ELECTRIC SHOCK DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE

RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR

S’adresser a un reparateur compétent.

use the polarized plug supplied
with the 302 with any extension
cord, receptacle, or other outlet
unless the blades can be fully
inserted.

Caution Identifies information that, if not

heeded, may cause damage to the
302 or other equipment in your
system.

Warning Identifies information that, if

ignored, may be hazardous to
your health or that of others.

CAPITALS Controls, switches or other

markings on the 302's chassis.

Boldface Strong emphasis.

Power source - This product is intended to

operate from a power source that does not
apply more than 255Vrms between the power
supply conductors or between either power
supply conductor and ground. A protective
ground connection, by way of the grounding
conductor in the power cord, is essential for
safe operation.

Danger from loss of ground - If the protective
ground connection is lost, all accessible
conductive parts, including knobs and
controls that may appear to be insulated, can
render an electric shock.

In-line power supply - This product receives its
operating power from the Symetrix PS-3 or PS-3E
power supply. These are the only
power supplies approved for use with the
product. Do not connect the product to any
other in-line, or plug-in, transformer. The use
of other power sources may cause damage to
the equipment or present a shock hazard to the
operator.

Operating location - Do not operate this
equipment under any of the following condi­tions: explosive atmospheres, in wet locations,
in inclement weather, improper or unknown AC
mains voltage, or if improperly fused.

Stay out of the box - To avoid personal injury
or injury to others, do not remove the product
covers or panels. Do not operate the product
without the covers and panels properly
installed.

Note Identifies information that needs

302

2

extra emphasis. A Note generally
supplies extra information to help
you to better use the 302.

Chapter 3

Fast First-Time Setup

Follow these instructions to get your 302 up-and-running as quickly as possible. The intent of this
section is fast setup only. Please refer to later chapters for explanation of the 302's controls and
functions.

1. Set the Microphone 1 and Microphone 2 GAIN controls completely counter-clockwise.

2. Set the Microphone 1 and Microphone 2 PAD switches to the OUT position.

3. Set the Microphone 1 and Microphone 2 POLARITY switches to the OUT position.

4. Set the PHANTOM POWER switch to the OUT position, unless you will be using a

condenser microphone which requires phantom power.

5. Connect your first microphone to the Microphone 1 XLR Input. If you are using two mics,
connect your second microphone to the Microphone 2 XLR Input.

Caution:Use only balanced microphones and cables!

6. Connect Output 1 and Output 2 of the Symetrix 302 to the inputs of the destination device.

7. Plug the 302 into an AC outlet using the external power supply (the Symetrix PS-3 or PS-3E).

Caution:Failure to connect the 302 to the proper AC mains voltage may

cause fire and/or internal damage.

Fast Setup

8. Turn the Microphone 1 and Microphone 2 GAIN controls slowly clockwise until you
achieve the desired output level from the 302.

9. Fast setup is now complete. Please refer to later chapters of this users guide or the
Symetrix Customer Service Department if you have additional questions.

302

3

Front Panel Controls Chapter 4

MICROPHONE 2 PHANTOM POWER

GAIN (dB)

40

20

60

15dB PAD

IN
OUT

POLARITY

180°
0°

ON
OFF

PWR

302

DUAL MICROPHONE
PREAMPLIFIER

CLIP

GAIN (dB)

40

20

MICROPHONE 1

15dB PAD

IN
OUT

60

POLARITY

180°
0°

CLIP

Front Panel

CLIP LED - The CLIP LED lights when the signal reaches 3dB below clipping. This LED should
never be on solidly. It is usually all right if the CLIP LED flashes occasionally, on peaks in the
program material. If you see the CLIP LED light, monitor your final signal destination to be sure
that you are not creating distortion by running audio levels that are too hot.

GAIN control - Sets the gain of the preamplifier from a minimum of 20dB to a maximum of 60dB.

15dB PAD - Reduces the input signal by 15dB when the switch is set to the IN position.

POLARITY push-button - Inverts the phase of the signal being amplified when the switch is set to
the IN position.

PHANTOM POWER - Applies a positive DC voltage to pins 2 and 3 of the XLR input jacks when
the switch is set to the IN position. This provides the ability to power condenser microphones
which require phantom power.

Caution: When Phantom Power is engaged, always turn your monitoring speakers and

headphones completely off before connecting or disconnecting any microphones to
the 302. This is to avoid a loud pop which occurs due to the sudden change in
voltage on XLR pins 2 & 3 when they are connected to, or disconnected from,
Phantom Power. Such a loud pop can result in speaker and/or hearing damage.

Caution:

See page 8 for more Do's and Don'ts of Phantom Powering.

Never connect an unbalanced microphone or mic cable to the input of the 302 when
the Phantom Power is engaged. This will short out the Phantom Power.

302

4

Rear Panel ConnectionsChapter 5

MICROPHONE INPUTS

INPUT 1INPUT 2

MANUFACTURED BY SYMETRIX INC. LYNNWOOD, WA USA

POWER

INPUT

THIS PRODUCT CONTAINS NO USER SERVICABLE PARTS.

FABRIQUÉ AUX E.-U. PAR SYMETRIX INC., LYNNWOOD, WASHINGTON.

RÉFÉREZ TOUTE RÉPARATION À UN TECHNICIEN QUALIFIÉ.

CONNECT TO
SYMETRIX PS-3
OR PS-3E POWER
SUPPLY ONLY.

OUTPUT 2

BALANCED LINE OUTPUTS

OUTPUT 2 OUTPUT 1+2

OUTPUT 1

OUTPUT 1

Rear Panel

POWER INPUT -7-pin DIN receptacle. Connect this to the 7-pin DIN plug of a Symetrix PS-3 or

PS-3E only. Connect the AC power connector of the PS-3 or PS-3E to
an AC power source that is of the correct voltage and frequency, as marked
on the PS-3 or PS-3E.

Note The PS-3 is a 117V AC power supply, used to power a single unit. The PS-3E is a

230V AC power supply, used to power a single unit. The PS-3 and PS-3E are Symetrix

accessories, available from your Symetrix dealer.

BALANCED LINE OUTPUTS

TRS jacks -1/4-inch tip-ring-sleeve (TRS) phone jack, wired:

Tip= high(+), Ring =low(-) and Sleeve=ground

Use these jacks when you need 1/4-inch balanced or unbalanced outputs (Output 1 or
Output 2). The nominal signal level here is +4 dBu. If you need an unbalanced output
use a tip-ring-sleeve phone plug for best results and connect only to the tip and sleeve.

Note Connecting an unbalanced cable here will result in an output level that is 6dB

lower than the output level achieved using a balanced cable.

Euroblock connectors - Low-profile balanced (+, - and ground) connectors, typically used in
contractor sound installations. Use these jacks when you need Euroblock balanced outputs
(Output 1, Output 2 or Output 1+2).

Note The signal at Output 1+2 is a combination of Output 1 and Output 2 signal, with

the level balance between Output 1 and Output 2 determined by the front-panel
GAIN and PAD settings.

MICROPHONE INPUTS

XLR inputs - Balanced XLR input jacks for Microphone 1 and Microphone 2.

(Pin 1 = ground, Pin 2 = +, Pin 3 = -)

These are mic-level inputs, designed to accept the balanced output from one
microphone.

Caution: When Phantom Power is engaged, do not use unbalanced microphones or

mic cables.

Caution: When Phantom Power is engaged, do not use switched mics which short

Pin 2 and /or Pin 3 to ground.

Caution: When Phantom Power is engaged, always turn down monitors/headphones

before connecting or disconnecting microphones.

302

5

302

6

Using the 302Chapter 6

The Preamplifiers

The 302's ultra-low noise, low distortion mic preamps provide direct-coupled balanced low-Z
inputs for optimum transient response and phase coherency. The positive and negative slew
rates are symmetrical, ensuring sonic integrity.

Gain Controls, Clip LEDs, Pads

The 302's gain controls set the gain of the preamp circuitry. They operate like the trim controls
found on most mixers. On a mixer the trim controls set the initial amount of amplification for each
mic input. The faders govern how much of the amplified signal is allowed to pass into the rest of
the system. Using a separate mic preamp such as the 302 assumes that somewhere downstream
there will be a volume control that functions like the fader on a mixing console.

The 302 offers 40dB overall gain range, from 20 dB to 60dB, when used without the pad.
Including the 15dB pad, the total range is 75dB, with a minimum overall gain of 5dB.

Any mic output level is easy to match with the 302's stepless gain control, regardless if it is
the -60dBV to -80dBV levels common with ribbon mics or the near line level often delivered by
transformerless condenser mics. Input signals as high as +14dBV can by handled by the 302.
(The front panel clip LEDs fire at 3dB below clipping.)

Both source level and preamp gain are directly related to the noise floor, as well as to head­room at the output. The key to using the 302 at its optimum performance level is to:

1. Use the maximum allowable source level.

2. Use only as much gain as necessary.

The combination of the highest possible input levels with the lowest possible gain always
results in minimum noise and maximum headroom.

The PAD push-buttons on the 302 reduce the input level at each channel by 15dB. Use these pads
when a very high output mic is used or when the incoming signal is so hot that the clip indicator is
lighted with the gain control at minimum. As previously mentioned, the 302 uses gain controls, not
volume controls or faders. It is not necessary to use the pads to reduce input levels in order to get
the gain controls to operate in some theoretical best position. The only best operating position
for a gain control is the minimum gain that delivers the required output level.

In addition to their more common use in reducing input signal strength, the pads can also give
the user a wider gain control-adjustment range for more accurate channel-to-channel level
matching. For very close level matching, the resolution of the gain controls at the very lowest
end of their range may be too coarse if the pads are not engaged. There is a trade-off here,
however: When using the pads the apparent noise floor is higher.

Polarity Push-buttons

Both channels include a polarity push-button. In the normal out position, signal source
polarity is maintained to the outputs. In the in position, the wiring from the XLR connector
pins 2 and 3 is reversed. This allows for correction of miswired cables, and for polarity match­ing of various manufacturers microphones.

Powering for Condenser Microphones

All condenser microphones require some kind of electrical power. This power may be supplied
by internal batteries, an external power supply that is connected to the microphone by a
special multiwire cable, or through a standard microphone cable by phantom or T system
powering. Phantom powering and T system powering are incompatible systems.

Phantom power derives its name from its invisibility to audio signals, even though the micro­phone cable carries both phantom power (as direct current) and audio signals (as alternating
current). Specifically, the term phantom power means a positive DC voltage sent to the microphone
on both audio leads, through current-limiting resistors which also serve to isolate the audio leads

302

7

from one another. The front panel phantom power button applies phantom power via pins 2 and 3
of the mic input XLR connectors.

The phantom power technique uses the two signal conductors in a standard balanced mic cable to
deliver the power required by the microphone, eliminating the need for internal batteries or an
external power supply. Because the voltage is applied equally to both sides of a floating balanced
circuit, no current flows through the microphone s transformer, or through the microphone element
itself.

It is often said that the sound of some dynamic microphones is affected by phantom power and
that ribbon mics cannot be plugged into an input that is phantom powered. For the most part, these
are myths that grew out of difficulties created by other problems in the mic circuit:

1. When XLR connectors are mated there is no guarantee that both pins 2 and 3 will make
contact at exactly the same time. It is possible that a damaging current could flow through
the mic for a brief moment under these conditions. However, this is a connector problem,
not a problem with the mic itself or phantom power in general.

2. In the past, it was a common practice to ground the center tap of the mic s output
transformer. However, this practice should be avoided in phantom powered systems. The
solution: Locate the center tap and cut the connection between it and pin 1 of the XLR
connector.

3. If the mic s output transformer has developed leakage, the microphone may become noisy
when phantom power is turned on. Crackling, sputtering or even humming noises may
occur. The leakage, not the power, is the problem. The solutions are:

A. Turn off the phantom power.
B. Put a 1:1 low-impedance transformer between the mic and the input.
C. Get the mic repaired.

The dominant remote powering system in use today is the phantom power system, which is
compatible with both condenser and non-condenser microphones (dynamics, ribbons, etc.). If your
microphone's specifications sheet claims that it requires phantom power, the Symetrix 302 can
power it.

The technical requirements for operation and/or compatibility are:

1. The microphone must have a balanced, low-impedance output.

2. The balanced output must be floating with respect to ground. If there is a center tap, it
must not be grounded.

In a nutshell, here are the do's and don'ts of phantom powering:

DO: Verify that your microphone can be phantom powered (if it is a condenser mic).

Ensure that your microphone s output is low impedance, balanced and floating. This is
especially important for ribbon mics.

Turn the phantom power off when connecting vintage ribbon microphones.

Mute your monitor speakers or headphones when turning the phantom power on or off.
If you don t, there will be a loud, nasty pop.

Mute your monitor speakers or headphones whenever you plug in or unplug a phantom
powered microphone. If you don t, there will be a loud, nasty pop.

DON'T:Plug in an A-B powered microphone without a suitable adapter.

Worry about your dynamic or ribbon microphones, as long as they are wired so that the
output is balanced and floating.

Use the microphone input for line-level sources, especially those that are transformerless.

Use the microphone input with unbalanced sources. Use a direct box to feed an

302

8

unbalanced source into the microphone input.

Worry about your tube condenser mics. They are compatible (although they cannot be
phantom powered).

Chapter 7

O

Applications

Dynamic or Ribbon Microphone

When using a dynamic or ribbon microphone with the Symetrix 302, use the following control
and switch settings:

GAIN: Completely counter-clockwise

PAD: Out

POLARITY: Out

PHANTOM POWER: Out

Slowly turn the GAIN control clockwise until the desired output level from the 302 is achieved.
If needed, engage the PAD and POLARITY switches.

DYNAMIC OR
RIBBON MICROPHONE.

THE 15dB PAD AND PHANTOM POWER
SWITCHES SHOULD BE IN THE OUT POSITION.

MICROPHONE 2 PHANTOM POWER

GAIN (dB)

15dB PAD

40

IN

CLIP

20

OUT

60

POLARITY

180°
0°

ON
OFF

PWR

302

DUAL MICROPHONE
PREAMPLIFIER

MICROPHONE 1

GAIN (dB)

40

CLIP

20

60

15dB PAD

IN
OUT

POLARITY

180°
0°

Condenser Microphone

When using a condenser microphone that requires Phantom Power with the Symetrix 302, use
the following control and switch settings:

GAIN:Completely counter-clockwise

PAD: Out

POLARITY: Out

PHANTOM POWER: In

Slowly turn the GAIN control clockwise until the desired output level from the 302 is achieved.
Condenser mics typically have a higher output than dynamic or ribbon mics, so the final GAIN
setting will typically be lower for a condenser mic than for a dynamic or ribbon mic. If needed,
engage the PAD and POLARITY switches.

Caution: If your condenser microphone uses T system powering, do not engage the

Phantom Power.

CONDENSER
MICROPHONE

302

DUAL MICROPHONE
PREAMPLIFIER

MICROPHONE 1

GAIN (dB)

40

CLIP

20

60

15dB PAD

IN
OUT

POLARITY

180°
0°

MICROPHONE 2 PHANTOM POWER

GAIN (dB)

15dB PAD

40

IN

CLIP

20

OUT

60

POLARITY

180°
0°

ON
OFF

PWR

ENGAGE IF NEEDED

ENGAGE TO PROVIDE
PHANT

M POWER

302

9

Guitar or Bass Pickups

The typical output level of guitar or bass pickups falls about halfway between mic level and
line level. Because the Symetrix 302 is designed to accept the output of the hottest condenser
microphone, the pickup output (not the amplifier output!) of a guitar or bass can generally be
connected to the input of the 302 through a 1:1 low-impedance transformer, without over-
loading the input of the 302. Never connect the guitar or bass directly to the mic input of the

302. The transformer connected between the guitar/bass and the 302 protects the circuitry of
the guitar/bass from Phantom Power, and it protects the 302's Phantom Power from short­circuiting. The transformer also balances the unbalanced output of the guitar/bass before it
reaches the input of the 302.

When using a guitar or bass as the input to the Symetrix 302, use the following control and
switch settings:

GAIN: Completely counter-clockwise

PAD: Out

POLARITY: Out

PHANTOM POWER: Out

Slowly turn the GAIN control clockwise until the desired output level from the 302 is achieved.
Engage the PAD and POLARITY switches if necessary.

LOW IMPEDANCE
TRANSFORMER

302

DUAL MICROPHONE
PREAMPLIFIER

BASS OR
GUITAR

THE PHANTOM POWER SWITCH
SHOULD BE IN THE OUT POSITION.

MICROPHONE 1

GAIN (dB)

40

CLIP

20

60

POLARITY

15dB PAD

180°

IN
OUT

0°

ENGAGE IF NEEDED

MICROPHONE 2 PHANTOM POWER

GAIN (dB)

15dB PAD

40

IN

CLIP

20

OUT

60

POLARITY

180°
0°

ON
OFF

PWR

302

10

TroubleshootingChapter 8

Troubleshooting Chart

SYMPTOM PROBABLE CAUSE

No output signalCheck cables and connections. Is a microphone connected to the 302's

input, and is the 302's output driving a line-level input? Check for AC
power presence. Make sure that your microphone and mic cable are
balanced. If you are using a mic or mic cable with a switch, is the switch
in the on position? If you are using a condenser microphone which
requires Phantom Power, did you turn the Phantom Power on?

Hum or buzz in output Check your cables. Ground loop: check related system equipment

grounding. Are all systemcomponents on the same AC ground? Make
sure that your microphone and mic cable are balanced.

DistortionCheck the level of the input signal on the 302's LED display. Is the

CLIP light on all the time? If so, reduce the incoming signal level by
turning the INPUT level counterclockwise. Is the incoming signal
already distorted? Make sure that your microphone is not broken, and
that the mic is not distorting.

Noise (hiss) Check input signal level. The input signal may be too low. If so, boost

the incoming signal (if possible) or move your mic closer to the signal
source. Is the input signal already noisy? Verify that all system compo­nents are on the same AC ground.

Noise (crackle) Check for broken mics and/or bad cables.

POWER LED not on Is the unit plugged in? Is the AC outlet OK?

CLIP LED on constantly Make sure that you are feeding the 302 a mic-level signal, not line-level.

Turn the GAIN control counter-clockwise and/or engage the mic pad. If
the CLIP LED is still on, reduce the level of signal that you are sending
to the input of the 302. Make sure that you are using the correct power
supply for your location. The PS-3 is for locales such as the United
States, which use 117V AC mains power, and the PS-3E is for locales,
such as Europe, that use 230V AC mains power.

302

11

Specifications Chapter 9

Architects and Engineers Specifications

The microphone preamp shall be a high­performance, dual channel, unit that is of a
single rack space wide and one rack space
high.

The unit shall provide two independent
channels of pre-amplification designed to
boost nominally mic level signals to line level.
Each channel shall have a gain control that is
continuously variable from 20dB to 60dB of
gain, a 15dB input pad, a polarity reversal
switch, and an LED indicator that lights in the
presence of signal peaks. There shall also be a
front panel pushbutton switch to engage
phantom power, and an LED that indicates the
presence of AC power.

The following connections shall be available
on the rear panel. Each channel shall have an
XLR3 mic input (wired pin 1 = ground, pin 2 =
+, pin 3 = -), a TRS line level output, and a
euroblock style removable terminal strip line
level output. There shall also be a mix output
that provides a sum of channels 1 and 2 via a
euroblock style removable terminal strip.

The microphone preamp shall be the Symetrix
Inc. model 302 Dual Microphone Preamplifier.

Specifications

Input/Output

Input Type Low Z Balanced, Transformerless
Maximum Input Level +14 dBV (with pad “In”)
Maximum Output Level +24 dBu Balanced, 10k Ohm load

Input Impedance >3k Ohms
Output Impedance 300 Ohms Balanced

Performance Data

Clip Indicators red LEDs, fire 3dB below clipping
Frequency Response 20Hz to 20kHz, +0, -1dB
THD+Noise .007% (1kHz, 0dBu, 600 Ohms out)

Signal to Noise Ratio 95 dB (-50 dBV, 150 Ohms in)
EIN <-128 dBu (150 Ohms source, 60 dB gain

Minimum Gain 20dB
Maximum Gain 60dB

302

12

+22 dBu Balanced, 600 Ohm load

150 Ohms Unbalanced

.01% (1kHz, +22dBu, 600 Ohms out)

22 kHz bandwidth)

Connections

Input XLR
Output TRS jacks, Euroblock
Power In 7 pin DIN

Physical

Size (hwd) 1.75 x 8.5 x 6.5 in., 4.445 x 21.59 x 15.875 cm.
Shipping Weight 4.5 lbs

Electrical

Power Requirements 117V AC nominal, 95-130V AC, 50 to 60 Hz

In the interest of continuous product improvement, Symetrix, Inc.
reserves the right to alter, change, or modify these specifications
without prior notice.

©1998, Symetrix, Inc. All rights reserved.

230V AC nominal, 165-255V AC, 50Hz

302 Limited Warranty

Warranty and ServiceChapter 10

Symetrix, Inc. expressly warrants that the product
will be free from defects in material and
workmanship for (18) months. Symetrix's
obligations under this warranty will be
limited to repairing or replacing, at
Symetrix's option, the part or parts of the
product which prove defective in material or
workmanship within (18) months from date
of shipment, provided that the Buyer gives
Symetrix prompt notice of any defect or
failure and satisfactory proof thereof.
Products may be returned by Buyer only
after a Return Authorization number (RA)
has been obtained from Symetrix. Buyer will
prepay all freight charges to return the
product to the Symetrix factory. Symetrix
reserves the right to inspect any products
which may be the subject of any warranty
claim before repair or replacement is carried
out. Symetrix may, at its option, require
proof of the original date of purchase (dated
copy of original retail dealer s invoice). Final
determination of warranty coverage lies
solely with Symetrix. Products repaired
under warranty will be returned freight
prepaid by Symetrix via United Parcel
Service (surface), to any location within the
Continental United States. At Buyer's
request the shipment may be returned via
airfreight at Buyer's expense. Outside the
Continental United States, products will be
returned freight collect.

The foregoing warranties are in lieu of all
other warranties, whether oral, written,
express, implied or statutory. Symetrix, Inc.

expressly disclaims any IMPLIED warran­ties, including fitness for a particular
purpose or merchantability. Symetrix's
warranty obligation and buyer s remedies
hereunder are SOLELY and exclusively as
stated herein.

This Symetrix product is designed and
manufactured for use in professional and
studio audio systems and is not intended for
other usage. With respect to products
purchased by consumers for personal, family,
or household use, Symetrix expressly

disclaims all implied warranties, including
but not limited to warranties of merchant­ability and fitness for a particular purpose.

This limited warranty, with all terms, condi­tions and disclaimers set forth herein, shall
extend to the original purchaser and anyone
who purchases the product within the
specified warranty period.

Symetrix does not authorize any third party,
including any dealer or sales representative,
to assume any liability or make any addi­tional warranties or representation regarding
this product information on behalf of
Symetrix.

This limited warranty gives the buyer certain
rights. You may have additional rights
provided by applicable law.

Limitation of Liability

The total liability of Symetrix on any claim,
whether in contract, tort (including negli­gence) or otherwise arising out of, con­nected with, or resulting from the manufac­ture, sale, delivery, resale, repair, replace­ment or use of any product will not exceed
the price allocable to the product or any part
thereof which gives rise to the claim. In no
event will Symetrix be liable for any inciden-

tal or consequential damages including but
not limited to damage for loss of revenue,
cost of capital, claims of customers for
service interruptions or failure to supply, and
costs and expenses incurred in connection
with labor, overhead, transportation, installa­tion or removal of products or substitute
facilities or supply houses.

302

13

Servicing the 302

If you have determined that your 302 requires repair services and you live outside of the
United States, please contact your local Symetrix dealer or distributor for instructions on
how to obtain service. If you reside in the U.S. then proceed as follows:

Before sending anything to Symetrix, contact our Customer Service Department for a
return authorization (RA) number. The telephone number is [phone] or email:
[e-mail]

In-warranty Repairs

To get your 302 repaired under the terms of the warranty:

1. Call us for an RA number.

2. Pack the unit in its original packaging materials.

3. Include your name, address, daytime telephone number, and a brief

statement of the problem.

4. Write the RA number on the outside of the box.

5. Ship the unit to Symetrix, freight prepaid.

We do not accept freight collect shipments.

Repairs made in-warranty will cost you only one-way freight charges. We'll prepay the
return (surface) freight.

If you send us your product in substandard packaging, we will charge you for factory
shipping materials. If you don t have the factory packaging materials, please use an
oversized carton, wrap the unit in a plastic bag, and surround it with bubble-wrap. Pack the
box full of Styrofoam peanuts. Be sure there is enough clearance in the carton to protect
the rack ears (you wouldn't believe how many units are returned with bent ears). We will
return the unit in Symetrix packaging. Of course, if the repair is due to operator error, parts
and labor will be charged. In any event, if there are charges for the repair costs, you will
pay for the return freight. All charges will be COD unless you have made other arrange­ments (prepaid, Visa or Mastercard).

Out-of-warranty Repairs

If the warranty period has passed, you'll be billed for all necessary parts, labor, packaging
materials, and freight charges. Please remember, you must call for an RA number before
sending the unit to Symetrix.

302

14

Declaration of ConformityChapter 11

Declaration of Conformity

We, Symetrix Incorporated,

6408 216th St. SW, Mountlake Terrace, Washington, USA,

declare under our sole responsibility that the product:

302 Dual Microphone Preamplifier

to which this declaration relates,

is in conformity with the following standards:

EN 60065

Safety requirements for mains operated electronic and related

apparatus for household and similar general use.

EN 50081-1

Electromagnetic compatibility - Generic emission standard

Part 1: Residential, commercial, and light industry.

EN 50082-1

Electromagnetic compatibility - Generic immunity standard

Part 1: Residential, commercial, and light industry.

The technical construction file is maintained at:

Symetrix, Inc.

6408 216th St. SW

Mountlake Terrace, WA, 98043

USA

The authorized representative located within the European Community is:

World Marketing Associates

P.O. Box 100

St. Austell, Cornwall, PL26 6YU, U.K.

Date of issue: September 1, 1998

Place of issue:Mountlake Terrace, Washington, USA

Authorized signature:

Dane Butcher, President, Symetrix Incorporated.

302

15

302

302

302

20

Symetrix, Inc.

6408 216th St. SW

Mountlake Terrace, WA, 98043

USA

Tel: [phone]

Fax: [phone]

Website: http://www.symetrixaudio.com

Email: [e-mail]