ENGINEERING SPECIFICATION
SYMCOM MODEL 201-100-SP-DPDT / 201-200-SP-DPDT
SINGLE-PHASE VOLTAGE MONITOR/PROTECTION RELAY
PART 1 GENERAL
1.1 REFERENCES
A. UL 508 Industrial Control Equipment – Underwriters Laboratories
IEC 60947 Low Voltage Switchg
B. ear and Controlgear – International Electrotechnical Commission
A S /I E C62.41 – American N
C. N I E ational Standards Institute/Institute of Electrical & Electronics Engineers
CSA C22.2 No 4E. 1 Industrial Control Equipment – Canadian Standards Asso
D. ciation
1.1 WARRA
PART 2 PRODUCTS
2.1 MA U A T
For Mod
The equipment s 100-SP-DPDT, manufactured by SymCom, Inc.
For Model 201-200
The equipment spe -200-SP-DPDT, manufactured by SymCom, Inc.
2.2 DESCRIPTION
2.3 PERFORM
F
For
NTY
A. Manufacturer aterial and workmanship defects for a
period of five years from the date of manufacture when installed and operated according to the manufacturer’s requirements.
N F C ERSUR
el 201-100-SP-DPDT
A. Regulator
The equipment shall be UL Listed as type NKCR—Industrial Control Equipment-Motor Controllers-Auxiliary Devices.
1.
2. The eq vices
Certified for C
3. The equipment s gear
and Cont
A. Protective
1. The equipment s
a. lo
B. Capabilitie
1. The equipment s
a. a
a. an C
b. a trip dela
c. a restart dela
d. voltage
2. The equipment s
3. The equipment s @ 240VAC.
4. T e t. The indicator light has the capability to indicate whether the phase monitor is in
run mode,
C. Electromagnetic
1. The equipment s r
discharge.
2. The equipment s be
3.5kV.
3. The equipment s evel 3
4kV line-to-lin and Level 4 4kV line-to-ground.
The equipment shall be immune to electrical surges per ANSI/IEEE C62.41 Surge and Ring Wave. Specified limits shall b
4. e
6k
5. The equipment s
D. Dielectric Isolation: Equipment withstands an alter nating current potential of 1000V plus twice the rated voltage of the equipment
for 1 minute without breakdown between uninsulated live parts and the enclosure with the contacts open and closed; between
terminals of opposite polarity with the contacts closed; and between uninsulated live parts of different circuits.
Warranty: The manufacturer shall guarantee the product to be free from m
pecified shall be the Model 201-
-SP-DPDT
cified shall be the Model 201
y Requirements:
uipment shall be ULC Listed as type NKCR7—Industrial Control Equipment-Motor Controllers-Auxiliary De
anada.
hall be CE marked for use in the European Union and evaluated against IEC 609 47 Low Voltage S witch
rolgear.
ANCE/DESIGN CRITERIA: SINGLE-PHASE VOLTAGE MONITOR/PROTECTION RELAY
Relay Functions
hall provide protection against the fol
voltage (90% of nominal setting)
w
s and Features
or Model 201 0-SP-DPDT
n adjustable voltage range of 95-120 VAC
Model 201-200-SP-DPDT
adjustable voltage range of 190-240 VA
a accur cy ±1%
h equipment shall have an indicator ligh
V line-to-line.
restart delay mode, or fault mode. Fault mode shall be low voltage.
lowing condition:
hall
include:
-10
y of 4 seconds for low voltage
y of 2 seconds
≤
hall include two isolated Form C output relay contacts pilot duty rated 480VA at 240VAC.
hall include two isolated Form C output relay contacts general purpose rated 10A
Compatibility
hall be immune to electrostatic discharge per IEC 61000-4-2, Level 3, 6 kV contact discharge and 8 kV ai
hall be immune to electrical fast transient bursts exceeding IEC 61000-4-4, Level 3. Specified limits shall
hall be immune to electrical surges per IEC 61000-4-5, Level 3 and Level 4. Specified limits shall be L
e,
hall be immune to radiated radio frequency emissions. Specified limits shall be 10V/m at 150 MHz.
ES-201-XXX-SP-DPDT_A1 7/16/2009
E. Environmental Requirements
1. The equipment shall operate continuously without derating in surrounding air temperatures of -20° to 70°C (-4° to 158°F).
2. The equipment shall operate continuously without derating in relative humidity of 10% up to 95% non-condensing per IEC 682-3.
3. T e r storage in ambient temperatures of -40° to 80°C (-40° to 176°F).
F. Dimension
G. Mounting:
h equipment shall operate properly afte
s: The equipment dimensions shall not exceed 1.750” H x 2.375” W x 4.125” (with socket).
1.
The equipment shall be mounted using the SymCom OT08 Octal Socket.
a T e o
. h s c et shall be 600V rated. k
b. The socket shall be 10A rated.
c. T
h se ocket shall provide a means for mounting on the surface or on a DIN rail.
End of Section
ES-201-XXX-SP-DPDT_A1 7/16/2009
Loading...