Symcom 201-100-DPDT-60mS, 201-200-DPDT-60mS Engineering Specification
ENGINEERING SPECIFICATION
SYMCOM MODEL 201-100-DPDT-60mS / 201-200-DPDT-60mS
3-PHASE VOLTAGE MONITOR/PROTECTION RELAY
PART 1 GENERAL
1.1 REFERENCES
A. UL 508 Industrial Control Equipment – Underwriters Laboratories
IEC 60947 Low Voltage Switchg
B. ear and Controlgear – International Electrotechnical Commission
A S /I E C62.41 – American N
C. N I E ational Standards Institute/Institute of Electrical & Electronics Engineers
CSA C22.2 No 4E. 1 Industrial Control Equipment – Canadian Standards Asso
D. ciation
1.1 WARRA
PART 2 PRODUCTS
2.1 M
For Mod
The equipment specified shall be 100-DPDT-60mS, manufactured by SymCom, Inc.
For Model 201-200
The equipment spe 00-DPDT-60mS, manufactured by SymCom, Inc.
2.2 DESCRIPTIO
2.3 PERFORM
For Model 201-10
NTY
A. Manufacturer Warranty: The manufacturer shall guarantee the product to be free from material and workmanship defects for a
period of five of manufacture when installed and operated according to the manufacturer’s requirements.
ANUFACTURERS
el 201-100-DPDT-60mS
A. Regulator
1.
2. The eq vices
3. The equipment s gear
A. Protective
1. The equipment s
B. Capabilitie
1. The equipment s
2. The equipment s
3. orm C output relay contacts general purpose rated 10A @ 240VAC.
4. T e in
C. Electromagnetic
1. The equipment s
2. The equipment s be
3. The equipment s 3
4. The equipment shall be immune to electrical surges per ANSI/IEEE C62.41 Surge and Ring Wave. Specified limits shall be
5. The equipment shall be immune to radiated radio frequency emissions. Specified limits shall be 10V/m at 150 MHz.
years from the date
the Model 201-
-DPDT-60mS
cified shall be the Model 201-2
N
y Requirements:
The equipment shall be UL Listed as type NKCR—Industrial Control Equipment-Motor Controllers-Auxiliary Devices.
uipment shall be ULC Listed as type NKCR7—Industrial Control Equipment-Motor Controllers-Auxiliary De
Certified for C
and Cont
ANCE/DESIGN CRITERIA: 3-PHASE VOLTAGE MONITOR/PROTECTION RELAY
a. phase
b. phase
c. low )
d. voltage
a. an adjustable
For Mo
a. an
b. a p
c. a trip dela
d. a restart dela
e. voltage
The equipment shall include two isolated F
h e uipment shall have an indicator lighq t. The indicator light has the capability to indicate whether the phase monitor is
run mode, al.
2.5kV.
4kV line-to-line, and Level 4 4kV line-to-ground.
6kV line-to-line.
anada.
hall be CE marked for use in the European Union and evaluated against IEC 609 47 Low Voltage S witch
rolgear.
Relay Functions
hall provide protection against the following conditions:
loss
reversal
voltage (90% of nominal setting
unbalance
s and Featuhres
all include:
0-DPDT-60mS
voltage range of 95-120VAC
del 201-200-DPDT-60mS
adjustable voltage range of 190-240VAC
hase unbalance trip point of 6%
y of 0.5 seconds for low voltage, unbalanced voltage and single-phasing faults.
y of 60 milliseconds
accuracy ≤ ±1%
hall include two isolated Form C output relay contacts pilot duty rated 480VA at 240VAC.
Compatibility
hall be immune to electrostatic discharge per IEC 61000-4-2, 3 kV contact discharge and 6 kV air discharge.
hall be immune to electrical fast transient bursts exceeding IEC 61000-4-4, Level 3. Specified limits shall
hall be immune to electrical surges per IEC 61000-4-5, Level 3 and Level 4. Specified limits shall be Level
srestart delay mode, or fault mode. Fault modes shall be low voltage, unbalance/single-phase and phase rever
ES-201-XXX-DPDT-6_A1 7/16/2009
D. Dielectric Isolation: Equipment withstands an alter nating current potential of 1000V plus twice the rated voltage of the equipment
for 1 minute without breakdown between uninsulated live parts and the enclosure with the contacts open and closed; between
terminals of opposite polarity with the contacts closed; and between uninsulated live parts of different circuits.
E. Env
ironmental Requirements
1. Th
e equipment shall operate continuously without derating in surrounding air temperatures of -20° to 70°C (-4° to 158°F).
2. The equipment s IEC 682-3.
3. T e r storage in ambient temperatures of -40° to 80°C (-40° to 176°F).
F. Dimension
G. Mounting:
h equipment shall operate properly afte
s: The equipment dimensions shall not exceed 2.330” H x 2.375” W x 4.125” (with socket).
1.
The equipment shall be mounted using the SymCom OT11 11-pin Socket.
a. The socket shall be 300V rated.
b. The socket shall be 10A rated.
c. The
socket shall provide a means for mounting on the surface or on a DIN rail.
hall operate continuously without derating in relative humidity of 10% up to 95% non-condensing per
End of Section
ES-201-XXX-DPDT-6_A1 7/16/2009
Loading...