Symbol ES3000 Quick Installation Manual

2

ES3000 Ethernet Switch - Quick Install Guide

To the Installer

This guide is intended for the technician responsible for installing the Symbol ES3000 Ethernet
Switch. It is also assumed that the technician is familiar with Ethernet LAN-based networking
concepts. The Symbol ES3000 Ethernet Switch is available in the following models:

•ES3000-PWR (supporting PoE) - Part Number ES-3000-PWR-10-WW

•ES3000 (non PoE) - Part Number ES-3000-10-WW

The purpose of this document is to provide specifications, features and guidelines for the installer to
use during installation. This document does not give site-specific installation instructions. Refer to

www.symbol.com for accessing the ES3000 User Guide (for general device configuration information)
and the ES3000 Advanced Concept Guide (for advanced configuration information unique to the ES3000).

Document Conventions

Before working on any equipment, be aware of the hazards associated with its installation and use.
Also, become familiar with standard practices for preventing accidents.

Indicates tips, hints and special requirements.

Care is required. Disregarding cautions can cause data loss or equipment damage.

Indicates a potentially dangerous condition or procedure that only Symbol-trained
personnel should attempt to correct or perform.

Power Cord Set

Only use a power cord approved for its intended country of operation:

U.S.A. and Canada The cord set must be UL-approved and CSA certified.

The minimum specification for the flexible cord is:

No. 18AWG

Type SV or SJ

3-conductor

The cord set must have a rated current capacity of at least 15A.

The attachment plug must be an earth-grounding type with a NEMA
5-15P (15A, 125V) or NEMA 6-15P (15A, 250V) configuration.

Denmark The supply plug must comply with section 107-2-D1, standard

DK2-1a or DK2-5a.

Switzerland The supply plug must comply with SEV/ASE 1011.

3

Others The power cord shall meet local regulation requirement, if any.

The appliance coupler (the connector to the unit and not the wall plug) must have a configuration for
mating with an EN60320/IEC320 appliance inlet.

4

ES3000 Ethernet Switch - Quick Install Guide

Warnings

• Only trained and qualified personnel are allowed to install this equipment.

• Remove any jewelry (rings, watches, necklaces, etc.) while installing this equipment.

• Install this equipment in racks with appropriate dimensions and weight allowances. Verify
racks are anchored and do not install in a way that can cause the equipment to tip and break.
Damage to the device or bodily injury can occur from equipment not appropriately mounted
and secured.

• Verify the unit and any device connected to it is properly wired and grounded.

• Attach only approved power cords to the device. Verify connecting power circuits have
appropriate overload protection.

• Verify the power connector is accessible at all times during the operation of the equipment.

• Do not work with equipment power circuits in dimly lit spaces.

• Do not install this equipment or work with its power circuits during thunderstorms or
weather conditions where power surges can exist.

• Verify adequate ventilation around the device, and that ambient temperatures meet
equipment operation specifications.

• For plugable equipment, the socket-outlet shall be installed near the equipment and shall be
easily accessible.

Introduction

The Symbol ES3000 Ethernet Switch provides centralized management of network components
across the wired network infrastructure. The Ethernet Switch connects directly to distributed LAN
resources (network switch or managed hubs). The rack-mountable design allows easy installation
with other network components.

The Ethernet Switch provides several features to assist in an efficient system installation:

• LED Indicators-indicate status for power and the condition of the Ethernet ports.

• Front-Mounted Ethernet Ports-allows easy access to Ethernet cabling.

• Serial Console Port - allows installers and administrators to connect directly to the device’s

command line interface (CLI).

Specifications

Width 482.6 mm with mounting brackets

440 mm without mounting brackets

Height 44 mm (1RU)

Depth 256 mm

5

Weight PoE version 8.95 lbs. (with rack brackets)

PoE version 8.80 lbs. (without rack brackets)
Non PoE version 7.90 lbs. (with rack brackets)
Non PoE version 7.75 lbs. (without rack brackets)

Max Power Consumption 100VAC - 240VAC, 50Hz/60Hz, 3.5A (PoE)

100VAC - 240VAC, 50Hz/60Hz, 1.5A (non PoE)

Operating Temperature 0º to 40ºC

Operating Humidity 10% to 85% (without condensation)

MTBFES-3000-PWR-10-WW 140,000 hours @ 25 C

ES-3000-10-WW 355,000 hours @ 25 C
FIBER-3000-1S-WW 1,250,000 hours @ 25 C

6

ES3000 Ethernet Switch - Quick Install Guide

Installation

Preparing for Site Installation

Site preparation for the ES3000 Ethernet Switch installation begins with a site survey and network
analysis. Review the site survey reports to determine specific equipment placement, site-specific port
capacity and power drops. Ensure the installation area is free of dust and dirt.

Review the following guidelines for site preparation:

• Assign installation responsibility to appropriate personnel.

• Identify where all installed components are located.

• Verify appropriate rack mounting requirements.

• Arrange for a sufficient number of power drops to support the equipment installation.

• Verify adequate ventilation to all installed equipment.

• Identify and prepare Ethernet and TCP/IP and serial port connections.

• Verify cable lengths are within maximum allowable distances for optimal signal
transmission.

Package Contents

Inspect the package contents and report any missing or damaged items to the Symbol sales
representative. The package (for both the PoE and non-PoE Ethernet Switch models) should contain
the following:

• ES3000 Ethernet Switch

• Quick Installation Guide

• Rack-mounting brackets

•Power cord (optional)

• Null-modem serial cable.

8

ES3000 Ethernet Switch - Quick Install Guide

Parity: None

Stop bits: 1

Flow control: None

3. Hit the return key <Enter> to display the ES3000 logon screen.

4. Enter a user name of admin and password of symbol. Press Enter.

5. Select System Admin from the main menu. Press Enter.

6. Select Access from the System Admin menu. Press Enter.

7. Select IP Config from the Access menu. Press Enter.

The System IP Configuration Menu displays.

To use the ES3000 Web Management interface to configure the device:

A network connection is required between the device and the host to use the Web
Management interface to configure the device.

1. Access the Web interface (using a Web browser) by entering the switch IP address into the
address bar. Press Enter.

Internet Explorer 5.0 or later or Netscape Navigator 6.0 or later is required.

2. Enter a user name of admin and password of symbol. Press OK.

The Web interface General Information page displays.

9

10

ES3000 Ethernet Switch - Quick Install Guide

Once the ES3000 user interface has been accessed using either the menu, CLI or Web
interfaces, refer to the ES3000 User Manual for advanced device configuration
information. Go to http://www.symbol.com/services/downloads

to access the guide.

Installing a SFP Fiber Transceiver

The ES3000 Ethernet Switch supports a SFP (small form factor pluggable) fiber channel transceiver
used in fiber channel cable installations.

To install the SFP Fiber Transceiver:

1. Remove the rubber plug protecting the optics on the transceiver.

2. Insert the transceiver into the fiber transceiver cage available on ports 25 or 26 on the
ES3000 Ethernet Switch.

3. Ensure one of the following two cable types is used when connecting fiber cable to the
ES3000 Ethernet Switch:

• LC 62.5um/125um multimode fiber optic cable

• LC 50um/125um multimode fiber optic cable

4. Consult the system administrator for cable length and installation specifications unique to
the installation environement.

If removing the SFP transceiver, disengage locking mechanism on SFP transceiver
carefully before removing the transceiver from the ES3000 Ethernet Switch.

Customer Support

Symbol Technologies provides its customers with prompt and accurate customer support. Use the
Symbol Support Center as the primary contact for any technical problem, question or support issue
involving Symbol products. If the Symbol Customer Support specialists cannot solve a problem,
access to all technical disciplines within Symbol becomes available for further assistance and
support. Symbol Customer Support responds to calls by email, telephone or fax within the time limits
set forth in individual contractual agreements.

When contacting Symbol Customer Support, please provide the following information:

• Serial number of unit

• Model number or product name

• Software type and version number

North American Contacts

Inside North America, contact Symbol at:

For sales and product information:

Symbol Technologies, Inc.
One Symbol Plaza
Holtsville, New York 11742-1300
Telephone: [phone]-SCAN 234
Fax: [phone]

11

For product support and service:

Symbol Global Support Center:
Telephone: [phone],
[phone] (Outside North America)
Fax: [phone]
Email: [e-mail]

12

ES3000 Ethernet Switch - Quick Install Guide

International Contacts

Outside North America, contact Symbol at:
Symbol Technologies, Inc.
Symbol Place
Winnersh Triangle, Berkshire, RG41 5TP
United Kingdom
Telephone: [phone] (Inside UK),
[phone] (Outside UK)

For other sales offices use the Symbol Services Web site for contact information

http://www.symbol.com/services/howto/howto_contact_us.html

Web Support Sites

Comprehensive On-line support is available at the MySymbolCare Web site. Registration is free and
a variety of services can be linked through this web-portal.

MySymbolCare

http://www.symbol.com/services/msc

Symbol Services Homepage

http://www.symbol.com/services

Symbol Software Updates

http://www.symbol.com/services/downloads

Symbol Developer Program Web site

http://devzone.symbol.com

Additional Information

Obtain additional information by contacting Symbol at:
Telephone: [phone] (Inside North America),
[phone] (Inside/Outside North America)
http://www.symbol.com/

Regulatory Information

All Symbol devices are designed to be compliant with rules and regulations in locations they are sold
and will be labeled as required.

Any changes or modifications to Symbol Technologies equipment, not expressly approved by Symbol
Technologies, could void the user’s authority to operate the equipment.

Laser Devices

The laser module complies with US 21CFR1040.10 & 1040.11 and
EN60825-1:1994+A11+A2. The laser classification is marked on the SFP Module.

Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The
following statement is required to comply with US and international regulations:

Caution: Use of controls, adjustments or performance of procedures other than those specified
herein may result in hazardous laser light exposure.

Radio Frequency Interference Requirements - FCC

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

13

Radio Frequency Interference Requirements - Canada

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe
A est conforme à la norme NMB-003 du Canada.

Marking and European Economic Area (EEA)

Class A ITE
WARNING

This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.

Statement of Compliance

Symbol Technologies, Inc., hereby declares that this device is in compliance with all the applicable
Directives, 89/336/EEC, 73/23/EEC. A Declaration of Conformity may be obtained from
http://www2.symbol.com/doc/

14

ES3000 Ethernet Switch - Quick Install Guide

Copyright

Copyright (c) 2004 by Symbol Technologies, Inc. All rights reserved.
No part of this publication can be modified or adapted in any way, for any purposes without permission in writing from Symbol. The material

in this manual is subject to change without notice.
Symbol reserves the right to make changes to any product to improve reliability, function, or design.
No license is granted, either expressly or by implication, estoppel, or otherwise under any Symbol Technologies, Inc., intellectual property

rights. An implied license only exists for equipment, circuits, and subsystems contained in Symbol products.
Symbol, the Symbol logo are registered trademarks of Symbol Technologies, Inc.
Other product names mentioned in this manual can be trademarks or registered trademarks of their respective companies and are hereby
acknowledged.
IBM is a registered trademark of International Business Machine Corporation.
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
Novell and LAN Workplace are registered trademarks of Novell Inc.
Toshiba is a trademark of Toshiba Corporation.

Patents

This product is covered by one or more of the following U.S. and foreign Patents:
4,593,186; 4,603,262; 4,607,156; 4,652,750; 4,673,805; 4,736,095; 4,758,717; 4,760,248; 4,806,742; 4,816,660; 4,845,350;

4,896,026; 4,897,532; 4,923,281; 4,933,538; 4,992,717; 5,015,833; 5,017,765; 5,021,641; 5,029,183; 5,047,617; 5,103,461;
5,113,445; 5,130,520; 5,140,144; 5,142,550; 5,149,950; 5,157,687; 5,168,148; 5,168,149; 5,180,904; 5,216,232; 5,229,591;
5,230,088; 5,235,167; 5,243,655; 5,247,162; 5,250,791; 5,250,792; 5,260,553; 5,262,627; 5,262,628; 5,266,787; 5,278,398;
5,280,162; 5,280,163; 5,280,164; 5,280,498; 5,304,786; 5,304,788; 5,306,900; 5,324,924; 5,337,361; 5,367,151; 5,373,148;
5,378,882; 5,396,053; 5,396,055; 5,399,846; 5,408,081; 5,410,139; 5,410,140; 5,412,198; 5,418,812; 5,420,411; 5,436,440;
5,444,231; 5,449,891; 5,449,893; 5,468,949; 5,471,042; 5,478,998; 5,479,000; 5,479,002; 5,479,441; 5,504,322; 5,519,577;
5,528,621; 5,532,469; 5,543,610; 5,545,889; 5,552,592; 5,557,093; 5,578,810; 5,581,070; 5,589,679; 5,589,680; 5,608,202;
5,612,531; 5,619,028; 5,627,359; 5,637,852; 5,664,229; 5,668,803; 5,675,139; 5,693,929; 5,698,835; 5,705,800; 5,714,746;
5,723,851; 5,734,152; 5,734,153; 5,742,043; 5,745,794; 5,754,587; 5,762,516; 5,763,863; 5,767,500; 5,789,728; 5,789,731;
5,808,287; 5,811,785; 5,811,787; 5,815,811; 5,821,519; 5,821,520; 5,823,812; 5,828,050; 5,848,064; 5,850,078; 5,861,615;
5,874,720; 5,875,415; 5,900,617; 5,902,989; 5,907,146; 5,912,450; 5,914,478; 5,917,173; 5,920,059; 5,923,025; 5,929,420;
5,945,658; 5,945,659; 5,946,194; 5,959,285; 6,002,918; 6,021,947; 6,029,894: 6,031,830; 6,036,098; 6,047,892; 6,050,491;
6,053,413; 6,056,200; 6,065,678; 6,067,297; 6,082,621; 6,084,528; 6,088,482; 6,092,725; 6,101,483; 6,102,293; 6,104,620;
6,114,712; 6,115,678; 6,119,944; 6,123,265; 6,131,814; 6,138,180; 6,142,379; 6,172,478; 6,176,428; 6,178,426; 6,186,400;
6,188,681; 6,209,788; 6,209,789; 6,216,951; 6,220,514; 6,243,447; 6,244,513; 6,247,647; 6,308,061; 6,250,551; 6,295,031;
6,308,061; 6,308,892; 6,321,990; 6,328,213; 6,330,244; 6,336,587; 6,340,114; 6,340,115; 6,340,119; 6,348,773; D305,885;
D341,584; D344,501; D359,483; D362,453; D363,700; D363,918; D370,478; D383,124; D391,250; D405,077; D406,581;
D414,171; D414,172; D418,500; D419,548; D423,468; D424,035; D430,158; D430,159; D431,562; D436,104.
5,912,662; 6,011873; 6,080,001; 6,234,389; 6,193,152B1;

Invention No. 55,358; 62,539; 69,060; 69,187 (Taiwan); No. 1,601,796; 1,907,875; 1,955,269 (Japan); European Patent 367,299; 414,281;
367,300; 367,298; UK 2,072,832; France 81/03938; Italy 1,138,713 3/02

15

72E-67923-01 Revision A